Shoring and Deep Excavation
Notes written by Skill-Lync from the recording · Updated 17 Nov 2026
What this workshop covers
This shoring and deep excavation workshop compares embedded retaining walls, from soldier piles to diaphragm walls, and the checks behind braced excavation. Recorded by Skill-Lync in March 2021, part 1 defines deep excavation, braced excavation and shoring, uses a building collapse in Shanghai to show what an unplanned excavation can do, lists the factors that drive ground movement, and then compares soldier pile, sheet pile, combi, secant pile, contiguous pile and diaphragm walls, with their construction steps, strengths and limits.
Part 2 covers wall selection by soil, watertightness, depth, programme and budget, the design guidance used (CIRIA C580, CIRIA C760, Eurocode 7), Rankine versus Coulomb earth pressure, dewatering and seepage, stability checks for kick-out, basal heave, sand boiling and upheaval, and numerical methods from limit equilibrium to PLAXIS, with sample results and a photo gallery of braced excavations.
It suits civil and geotechnical students and junior engineers who already know active and passive earth pressure. It is a survey, not a worked design: there are no hand calculations or software walkthroughs, and anchored walls and strut design are only touched on.
Chapters
Part 1
- 0:00 Agenda and what counts as a deep excavation
- 2:12 Case history: building collapse in Shanghai
- 3:30 Ground movement factors and open cut excavation
- 5:29 Soldier pile walls: lagging, reuse, water limits
- 8:31 Sheet pile walls and when they can be driven
- 10:38 Combi walls: tubular piles with sheet piles
- 11:50 Secant pile walls: primary, secondary, hard-soft
- 15:02 Contiguous pile walls
- 16:21 Diaphragm walls for deep urban excavations
Part 2
- 0:00 Wall selection table by soil, depth and budget
- 2:29 Design guidance: CIRIA C580, C760, Eurocode 7
- 3:38 Rankine vs Coulomb earth pressure theory
- 5:04 Dewatering and seepage analysis
- 7:27 Stability checks: shear failure and kick-out
- 8:31 Basal heave, sand boiling and upheaval
- 10:00 Advanced numerical modelling requirements
- 11:01 Limit equilibrium vs WALLAP vs PLAXIS and FLAC
- 14:56 Reading PLAXIS displacement and moment results
Key points from the session
- The instructor treats any excavation deeper than 4.5 m as a deep excavation. In cities the main risk is excavation-induced ground movement damaging nearby buildings and utilities, which is limited with an embedded wall supported by struts, props or anchors.
- Soldier pile walls (steel I or H sections with timber or concrete lagging placed as digging proceeds) are quick, can skip around utilities and can be pulled out for reuse, but leak at the joints, so they are unsuitable below the water table in cohesionless soil, and extraction disturbs adjacent ground.
- Steel sheet piles interlock, retain water and are reusable, but the instructor gives a practical length limit of about 30 m, a risk of declutching in coarse soils and no use in hard ground or rock because they must be driven. Combi walls add large tubular piles that carry load, with sheet piles in between.
- Secant pile walls overlap unreinforced primary (female) piles with reinforced secondary (male) piles, cut into the primaries. A guide wall holds verticality to about 1 in 75, the overlap is usually limited to 100-200 mm, and hard-hard, hard-soft and mixed patterns trade stiffness against drilling effort. Contiguous piles leave gaps, so they are cheaper and faster but cannot hold back water.
- Diaphragm walls are built panel by panel under support fluid after a guide wall. They suit almost any soil, can go deeper than 60 m by the instructor's account, have few joints, can sit right against existing buildings and work with top-down construction, which is why metros use them; the drawbacks are disposing of support fluid and a large site footprint.
- Rankine theory ignores wall friction and assumes infinite failure planes; Coulomb uses force equilibrium on a single wedge and includes wall friction. The instructor warns that the wrong earth pressure theory gives an uneconomical or unsafe wall.
- Stability checks named: embedment against kick-out, basal heave by bearing capacity, negative bearing capacity or slip circle methods, sand boiling with a factor of safety of 1.5, and upheaval of an impermeable layer over a permeable one with a factor of safety of 1.2, relieved by wells or dewatering.
What is the difference between a secant pile wall and a contiguous pile wall?
In a secant pile wall the piles overlap: unreinforced primary piles are cast first, then reinforced secondary piles are drilled into them, giving a continuous wall that can hold back groundwater. Contiguous piles stand side by side with small gaps, so they are faster and cheaper to build but cannot retain water and need a facing.
When should I use a diaphragm wall for an excavation?
The instructor recommends diaphragm walls for deep excavations in crowded urban sites, such as metro stations, where the wall must be stiff, watertight and close to existing buildings. They work in most soils, can be very deep and can become the permanent wall, but need large equipment and support fluid handling.
Which software is used to design deep excavations and retaining walls?
The session compares three levels. Limit equilibrium methods need only soil strength but give no deformations. Pseudo-finite element tools like WALLAP give wall movement but not ground movement. Finite element PLAXIS or finite difference FLAC model full soil-structure interaction and construction sequence in 2D or 3D, but need far more input data.
Where to go next
- Geotechnical investigation course at Skill-Lync
- Workshop: soil anchors analysis and applications
- GATE CE foundation engineering: solved earth pressure and pile questions
- GATE CE soil mechanics: solved seepage and consolidation questions
- Geotechnical engineering in site investigation and foundation design
Who should watch
For Civil Engineers
A 24 Mar 2021 workshop recording from Skill-Lync on CIVIL. For a structured course with projects on this topic, see Skill-Lync's civil engineering courses.