Recorded workshop · CIVIL

Geotechnical Earthquake Engineering

Held 24 Mar 20212 videos

Notes written by Skill-Lync from the recording · Updated 17 Nov 2026

What this workshop covers

An introduction to geotechnical earthquake engineering: how soil changes earthquake shaking through site amplification, liquefaction and seismic landslides.

In part 1 the instructor builds up from engineering seismology. Risk is split into hazard, vulnerability and value, and engineers work on vulnerability. He then covers the causes of earthquakes, plate tectonics and the three boundary types as they apply to the Himalaya and Gujarat, focus versus epicentre, magnitude versus intensity, and P, S and surface waves. The geotechnical part starts with local site effects, earthquake-triggered landslides and liquefaction explained through effective stress.

Part 2 is about site amplification: why soft and deep soils shake more than rock, what an amplification or transfer function is, case histories from Mexico City in 1985 and Loma Prieta in 1989, and the two methods a designer meets in practice, Vs30 and 1D ground response analysis. This Skill-Lync session was recorded in March 2021 and is a conceptual lecture for civil engineering students and graduates. It has no calculations, no software walkthrough and no liquefaction or slope stability design method, so treat it as a primer before a soil dynamics course.

Chapters

Part 1

  1. 0:35 Earthquake risk: hazard, vulnerability and value
  2. 2:49 Causes of earthquakes, including reservoir-induced
  3. 5:29 Earth's structure and moving tectonic plates
  4. 8:03 Divergent, convergent and transform boundaries
  5. 12:43 Focus, epicentre, magnitude and intensity
  6. 15:59 P, S and surface waves in a seismogram
  7. 18:34 Local site effects and earthquake geohazards
  8. 19:46 Earthquake-triggered landslides: the Kobe example
  9. 21:37 Liquefaction as loss of effective stress

Part 2

  1. 0:09 Site amplification and the 1819 Kutch account
  2. 1:52 What controls amplification: soil, topography, resonance
  3. 6:04 Why waves amplify when they enter soft soil
  4. 7:16 Amplification and transfer functions
  5. 9:36 Animation: identical buildings on rock and soft soil
  6. 12:57 Mexico City 1985: damage in the lake zone
  7. 14:59 Loma Prieta 1989: amplification in San Francisco Bay
  8. 16:46 Vs30 and 1D ground response analysis
  9. 19:55 Why it matters for north India and research

Key points from the session

  • Seismic risk combines hazard, vulnerability and value. Engineers cannot change the hazard, only understand it through engineering seismology, so earthquake engineering is about reducing vulnerability with well-designed structures and foundations.
  • Do not confuse magnitude and intensity. Magnitude is the energy released at the focus, and each whole step is roughly 30 times more energy. Intensity is the shaking felt at a place, so it depends on distance and on the ground under the site.
  • The gap between P-wave and S-wave arrival gives the distance to the epicentre, and distances from several stations locate it. For the Himalayan region the instructor cites about 5 km/s for P waves and about 2.5 km/s for S waves.
  • Liquefaction follows from the effective stress equation: sudden shaking of saturated sand raises pore water pressure, effective stress falls to zero and so does shear strength because sand has no cohesion. Buildings can then tilt or topple intact, as in the 1964 Niigata photos.
  • Site amplification is the soil-site motion divided by the rock motion in the frequency domain. Soft, deep soil slows the waves and raises their amplitude, can lengthen the shaking, and resonates when the soil frequency matches the input motion. Hilltops amplify shaking too.
  • Soft soil lowers the frequency of shaking, which matches taller buildings. In Mexico City in 1985, 350 km from the epicentre, most collapses were 5 to 20 storey buildings on the soft lake deposits, while buildings in the foothill zone were not damaged.
  • Vs30, the average shear wave velocity of the top 30 m, is the standard site class measure in foreign codes. The instructor notes that the Indian code (as of 2021) classifies soil only as rock, hard or soft using SPT N values, partly because India has little Vs30 data.

What is geotechnical earthquake engineering?

It is the branch of earthquake engineering that studies how soil behaves during shaking and how it changes the motion reaching a structure. The session covers its main problems: site amplification by soft or deep soil, liquefaction of saturated sand, and earthquake-triggered landslides. Knowing the soil strata under a building is treated as essential for seismic design.

Why does soil liquefy during an earthquake?

In saturated sand the sudden earthquake load is carried by the pore water, which cannot drain in a few seconds. Pore water pressure rises until effective stress drops to zero. Since sand has no cohesion, its shear strength becomes zero too, and the ground can no longer carry foundations, so buildings sink or topple.

Why can a place far from the epicentre shake more than one near it?

Because local soil can amplify the waves. The instructor's example is the 1989 Loma Prieta earthquake: intensity was about VII near the epicentre but IX in the San Francisco Bay area roughly 100 km away, and recorded accelerations on Treasure Island's soil were about three times those on the rock of Yerba Buena Island.

Where to go next

Who should watch

For Civil Engineers

A 24 Mar 2021 workshop recording from Skill-Lync on CIVIL. For a structured course with projects on this topic, see Skill-Lync's civil engineering courses.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.