Gear speed calculator: rpm per gear and the best gear for mileage

Enter a tyre size and gear ratios to get the engine rpm at any road speed in every gear, the speed each gear reaches at the rev limit and where the rpm lands after each upshift. Add the car's mass, drag and torque curve to see which gears can hold a speed or a slope, and which one burns the least fuel. A third tab checks what a tyre size change does to the speedometer. Free, runs in your browser.

Manufacturer gear ratios · road-load model · Willans-line fuel estimate · checked against an independent Python model · Updated 22 Nov 2026

The tyre size fills the radius with the unloaded size; a loaded tyre rolls on a radius a few percent smaller. Primary reduction is the crank-to-gearbox ratio on motorcycles; leave 1 for cars.

rpm in top gear1,611at 60 km/h
rpm in 1st7,963at 60 km/h
Top gear at rev limit224 km/h6,000 rpm
  • Calculating…
Engine rpm against road speed in every gear, with the rev limit020004000600005010015020012345road speed (km/h)engine rpm

How do you calculate engine rpm from speed and gear?

The engine turns the wheels through the gearbox and the final drive, so engine speed is wheel speed times the overall ratio. Wheel speed is road speed divided by the tyre's circumference:

Here v is road speed in m/s, r the tyre's rolling radius in metres, ig the gear ratio, if the final drive ratio and ip the primary reduction (motorcycles have one between the crank and the gearbox; for a car it is 1). The tyre size on the sidewall gives the diameter:

Take the third-generation Suzuki Swift 1.2 five-speed manual. Suzuki's technical data lists gear ratios of 3.545, 1.904, 1.240, 0.914 and 0.717, a final drive of 4.294 and 175/65 R15 tyres. The tyre is 608.5 mm across unloaded, so r = 0.3043 m. At 60 km/h:

GearRatiorpm at 60 km/hrpm at 100 km/hSpeed at 6,000 rpm
13.5457,96313,271 (over the limit)45 km/h
21.9044,2777,128 (over the limit)84 km/h
31.242,7854,642129 km/h
40.9142,0533,422175 km/h
50.7171,6112,684224 km/h

A loaded tyre rolls on a slightly smaller radius than its unloaded size, so a real engine turns a few percent faster than these figures. Enter a measured rolling radius if you have one: drive a known distance, count wheel turns, divide by 2π.

Engine rpm against road speed in every gear, with the rev limit020004000600005010015020012345road speed (km/h)engine rpm

Each gear is a straight line through zero. The stepped line is a run through the gears changing up at 2,500 rpm. After each upshift the engine drops by the ratio of the two gears:

In the Swift, a 2,500 rpm change from 1st lands at 1,343 rpm in 2nd, from 2nd at 1,628 in 3rd, and from 4th at 1,961 in 5th. Close ratios at the top keep the drops small; the big step is 1st to 2nd.

Which gear gives the best mileage?

At a steady speed the road asks for the same power in any gear. What the gear changes is how the engine delivers it. A higher gear turns the engine slower, so it must make more torque per revolution, and it runs at a higher load with the throttle further open. A petrol engine at light load loses a big share of its fuel to friction and to pumping air past a nearly closed throttle. At higher load those losses are a smaller share of the work.

The calculator first works out the force and power the road needs:

For the Swift at 60 km/h, with 915 kg (840 kg kerb plus a 75 kg driver), Crr = 0.01 and CdA = 0.32 × 2 m² (assumed, Suzuki does not publish a drag coefficient), the road needs 196.4 N and 3.27 kW at the wheels, so the engine supplies 3.56 kW through a 92% efficient driveline. Then it checks every gear:

GearrpmTorque neededFull-load torqueLoadBSFC (est.)Fuel (est.)
17,9634.27 N·m–––over the rev limit
24,2777.95 N·m119 N·m6.7%619 g/kWh4.89 L/100 km
32,78512.2 N·m111 N·m11%475 g/kWh3.76 L/100 km
42,05316.6 N·m104 N·m16%405 g/kWh3.2 L/100 km
51,61121.1 N·m96.6 N·m22%362 g/kWh2.86 L/100 km

5th uses about 24% less fuel than 3rd and 41% less than 2nd at the same 60 km/h. Even in 5th the engine is at only 22% of its full-load torque, so its estimated BSFC of 362 g/kWh is far from its best. That is why small cars are most economical at moderate speeds in top gear and not at crawling speeds.

Full-load torque curve with the torque each gear needs at this speed05010002000400060002345engine rpmtorque (N·m)

The dashed line is the constant power the road needs at 60 km/h. Each gear meets it at a different rpm. Higher gears sit further left and higher up the torque axis, nearer the full-load curve where the engine is most efficient. The vertical line marks the lowest rpm the engine pulls smoothly (1,200 rpm here, an assumed figure). Below it the engine labours, so the calculator won't recommend a gear that puts the engine there.

Gear ratios of four Indian vehicles

The Vehicle menu loads gearing published by the makers. Here is what the calculator gives for each at a steady speed:

VehicleRatios (1st to top) × finalTyreTop gear rpm at 80 km/hBest gearTop speed (est.)
Suzuki Swift 1.2 petrol 5MT (3rd gen)3.545 / 1.904 / 1.24 / 0.914 / 0.717 × 4.294175/65 R152,1475 of 5182 km/h
Maruti Suzuki Dzire 1.2 petrol 5MT (2024)3.545 / 1.905 / 1.24 / 0.906 / 0.697 × 4.389185/65 R152,0895 of 5177 km/h
Mahindra XUV500 2.2 diesel 6MT (overall ratios)16.823 / 8.679 / 5.035 / 3.842 / 3.2 / 2.716235/65 R171,5636 of 6171 km/h
Royal Enfield Goan Classic 350, 5-speed2.313 × 2.615 / 1.706 / 1.3 / 1.04 / 0.875 × 2.8130/90-163,7565 of 5119 km/h

Two of them need care. Mahindra's XUV500 gearbox has two final drives (4.05 for 1st to 4th, 3.115 for 5th and 6th), so the menu enters its overall ratios with the final drive set to 1. The Royal Enfield Goan Classic 350 has a primary reduction of 2.313 between the crank and the gearbox, so its overall top ratio is 2.313 × 0.875 × 2.8 = 5.667. Its top speed comes before the rev limit in 5th, as on many small bikes: 5th is a cruising gear.

Makers do not publish drag coefficients for these vehicles or full torque curves, so those inputs are typical values. Each preset's assumed inputs: Suzuki Swift 1.2 petrol 5MT: Cd 0.32 x 2.0 m2, Crr 0.010, 75 kg driver, torque below 4,400 rpm, 1,200 rpm lowest smooth speed, 92% driveline. Maruti Suzuki Dzire 1.2 petrol 5MT: Cd x A 0.6 m2 and Crr 0.012 (Guzzella and Sciarretta's compact class), 75 kg driver, torque away from 4,300 and 5,700 rpm, 6,000 rpm limit. Mahindra XUV500 2.2 diesel 6MT: Cd x A 1.2 m2 and Crr 0.017 (Guzzella and Sciarretta's SUV class), 75 kg driver, torque below 1,600 and above 3,750 rpm, 4,200 rpm limit. Royal Enfield Goan Classic 350: Cd x A 0.56 m2 with rider, Crr 0.012, 75 kg rider, torque away from 4,000 and 6,100 rpm, 1,800 rpm lowest smooth speed, 90% chain drive.

What is the most economical speed?

Rolling resistance is almost constant with speed, but air drag grows with its square. Fuel per kilometre follows the force. For the Swift example, the road force rises 34% from 100 to 120 km/h, but the estimated fuel use in 5th rises only 24%. The engine works at a higher, more efficient load at 120 km/h, which recovers part of the extra drag. Natural Resources Canada puts the real-world figure at about 20% more fuel at 120 km/h than at 100 km/h.

Estimated fuel use against steady speed in every gear the engine can pull02.557.51005010015020012345steady speed (km/h)L/100 km

Each line is one gear, drawn only where the engine can hold that speed without dropping below 1,200 rpm, exceeding the rev limit or running out of torque. The dashed line is the best gear at each speed with a 20% torque reserve. Its lowest point is at about 45 km/h, which is where 5th gear reaches the lowest smooth engine speed. Go slower and you must drop to 4th, which turns the engine faster for every kilometre and adds friction loss. Go faster and air drag climbs. Each downward step in the dashed line is an upshift.

India's Petroleum Conservation Research Association advises 45-55 km/h in top gear, which matches this result. On shift points, the UK Energy Saving Trust says to change up early, usually by about 2,000 rpm. Spain's energy agency IDAE gives 2,000-2,500 rpm for petrol engines and 1,500-2,000 rpm for diesels, since a diesel makes its torque lower down. No single number fits every car: a taller top gear or a diesel engine moves the sweet spot.

Why you need a lower gear on a hill

A grade adds m g sin θ to the road force. For the Swift at 40 km/h on an 8% grade that is 716 N on top of the rolling and air resistance, and the engine must supply 10.3 kW. The torque each gear needs:

  • Gear 1: 5,309 rpm, 18.5 N·m (17% of full load)
  • Gear 2: 2,851 rpm, 34.5 N·m (31% of full load)
  • Gear 3: 1,857 rpm, 53 N·m (52% of full load)
  • Gear 4: 1,369 rpm, 71.8 N·m (78% of full load)
  • Gear 5: 1,074 rpm, 91.6 N·m (106% of full load), below the lowest smooth rpm

With a 20% torque reserve the calculator picks gear 4. A gear at more than about 80% of full-load torque has nothing left to accelerate or to cope with a steeper patch, so the reserve setting is how you tell the calculator not to lug the engine.

How the fuel model works: the Willans line

Engine maps (BSFC contours over rpm and torque) are measured on a dynamometer and rarely published. The calculator uses the Willans line, a straight-line fit that engine researchers use when they don't have a map. At a given speed, the brake mean effective pressure (bmep, torque per unit displacement) rises in a straight line with the fuel mean effective pressure (pmf, fuel energy per cycle per unit displacement):

The slope e is the indicated efficiency, the share of fuel energy that becomes work on the pistons. The offset pme0 is the work lost to friction and pumping, expressed as a pressure. It grows with rpm. Hl is the fuel's lower heating value. The defaults are e = 0.4 and pme0 = 1.6 bar, the naturally aspirated petrol example in Guzzella and Sciarretta's Vehicle Propulsion Systems for petrol and e = 0.45 and pme0 = 1.0 bar (assumed: Guzzella and Onder put a diesel's efficiency factor at a maximum around 0.46, and its pumping loss at 0.1-0.2 bar against about 0.9 bar for a throttled petrol engine) for diesel. Fuel properties: petrol 43.5 MJ/kg at 750 kg/m³, diesel 42.6 MJ/kg at 846 kg/m³.

Guzzella and Sciarretta note that for first estimates e and pme0 are often taken as constants, which is what the defaults do. You can add speed terms (k1, k2) if you have friction data for your engine. The model gets the direction and the relative size of the gear and speed effects right. Its absolute fuel figures come out lower than what cars return on the road: the Swift example gives 34.9 km/L at a steady 60 km/h. The model leaves out accessories (AC, alternator), warm-up, mixture enrichment and the extra pumping loss of a nearly closed throttle at very light load. With these numbers the Swift's engine idling at 800 rpm would burn 0.37 L/h, below the 0.95-1.9 L/h fueleconomy.gov gives for idling, depending on engine size and AC use. So use the fuel column to compare gears and speeds, not to predict your mileage.

Tyre size change and speedometer error

The speedometer counts revolutions, so it assumes the original tyre's circumference. A tyre with a bigger diameter covers more road per turn: the car moves faster than the dial shows, and the engine turns slower at any real speed. Examples worked out by the calculator:

FromToDiameterChangeDial 100 km/h is really
175/65 R15185/65 R15608.5 → 621.5 mm+2.1%102.1 km/h
175/65 R15185/60 R15608.5 → 603 mm-0.9%99.1 km/h
195/55 R16205/55 R16620.9 → 631.9 mm+1.8%101.8 km/h
215/60 R16235/65 R17664.4 → 737.3 mm+11%111 km/h
100/90-18110/90-18637.2 → 655.2 mm+2.8%102.8 km/h

Keep the change within about ±3% of the original diameter, a common fitment rule of thumb, so the speedometer, ABS and gearing stay close to what the car was designed for. UN ECE Regulation 39 allows a speedometer to over-read but never under-read, so makers set them to read a little high. A bigger tyre eats into that margin.

What this calculator does not model

  • Acceleration. Results are for a steady speed. Accelerating adds m a to the road force and changes which gear is best.
  • The real engine map. The fuel figures come from a generic Willans line, not a measured BSFC map, and the torque curves between published points are interpolated.
  • Tyre slip and rolling radius changes. The rolling radius is taken as constant. A loaded, worn or under-inflated tyre rolls on a smaller radius.
  • Wind, AC, alternator and other accessory loads. These add to the engine load and raise fuel use at low speed most of all.
  • Automatics and CVTs. The physics is the same, but the controller chooses the ratio and torque converters add slip losses.
Learn powertrain modelling

Skill-Lync's vehicle dynamics and hybrid vehicle courses build these models in MATLAB and Simulink: road load, gear ratios, engine maps and drive cycles, then a full longitudinal vehicle model.

Frequently asked questions

How do I calculate engine rpm from speed and gear ratio?

Divide the road speed in m/s by the tyre's circumference (2πr) to get wheel revolutions per second, multiply by 60 for per minute, then by the gear ratio and the final drive ratio (and the primary reduction on a motorcycle). A Suzuki Swift 1.2 at 60 km/h in 5th (0.717 × 4.294, 175/65 R15 tyre) turns at about 1,611 rpm; in 3rd it turns at 2,785 rpm.

Which gear gives the best mileage?

The highest gear the engine can pull smoothly at your speed. At the same road speed the road needs the same power whatever the gear, but a higher gear runs the engine slower and at a higher load, so less of the fuel is lost to friction and pumping. For the Swift example at 60 km/h this calculator estimates 2.86 L/100 km in 5th against 3.76 in 3rd.

At what rpm should I change gear for fuel economy?

Change up early, usually around 2,000 rpm when accelerating gently (the UK Energy Saving Trust's advice), as long as the engine pulls cleanly in the next gear. In the Swift, an upshift at 2,500 rpm from 2nd drops the engine to 1,628 rpm in 3rd. Use the speed-and-rpm tab to see where every shift lands for your car.

What is the top speed in each gear?

The speed at the rev limit, v = 2πr n / (60 i), unless the engine runs out of power first. With a 6,000 rpm limit the Swift reaches 45 km/h in 1st and 84 km/h in 2nd. In 5th the road load wins first: with the assumed drag the power runs out at about 182 km/h, before the rev limit.

How does a bigger tyre change speedometer reading?

The speedometer counts wheel or gearbox revolutions, so a larger-diameter tyre covers more road per revolution and the car moves faster than the dial says. Going from 175/65 R15 to 185/65 R15 grows the diameter by 2.1%, so an indicated 100 km/h becomes 102.1 km/h.

What is the Willans line?

A straight-line engine fuel model: at a given speed, brake mean effective pressure rises linearly with fuel mean effective pressure, bmep = e·pmf − pme0. The slope e is the engine's indicated efficiency and the offset pme0 is the friction and pumping loss. It explains why part-load efficiency is poor: at low load the fixed loss pme0 is a large share of the fuel burned.

Related on Skill-Lync

Sources

  • Suzuki, Swift technical data, 1.2 DUALJET 5MT (Suzuki Belgium, 2017, read 17 Nov 2026): gear ratios 3.545 / 1.904 / 1.240 / 0.914 / 0.717, final drive 4.294, 66 kW at 6,000 rpm, 120 N·m at 4,400 rpm, 175/65 R15, kerb 840-890 kg. Suzuki New Zealand Swift 3rd gen specifications: 1,242 cm³ (73.0 × 74.2 mm).
  • Suzuki Auto South Africa, Dzire brochure (January 2026, read 22 Nov 2026): Z12E 1,197 cm³, 60 kW at 5,700 rpm, 112 N·m at 4,300 rpm; 5MT ratios 3.545 / 1.905 / 1.240 / 0.906 / 0.697, final 4.389; 185/65 R15; kerb 935-940 kg. South African-market ratios; Maruti Suzuki's India launch release (Nov 2024) gives the same engine output.
  • Mahindra, XUV500 W6/W8 owner's manual §2.8 (read 22 Nov 2026): 2,179 cm³, 103 kW at 3,750 rpm, 330 N·m at 1,600-2,800 rpm; overall ratios 16.823 / 8.679 / 5.035 / 3.842 / 3.2 / 2.716 (two final drives, 4.05 and 3.115); P235/65 R17; kerb 1,785 kg (FWD).
  • Royal Enfield, Goan Classic 350 technical specification (read 22 Nov 2026): primary 2.313, gears 2.615 / 1.706 / 1.3 / 1.04 / 0.875, final 2.8, 20.2 bhp at 6,100 rpm, 27 N·m at 4,000 rpm, max 7,000 rpm, rear 130/90-16, kerb 197 kg.
  • L. Guzzella and A. Sciarretta, Vehicle Propulsion Systems, 2nd ed., Springer (2007): the Willans approximation pme = e·pmf − pme0 (eq. 3.6), the petrol example e = 0.4, pme0 = 1.6 bar (eq. 3.26), petrol 43.5 MJ/kg and 0.75 kg/L, and road-load classes (Table 2.1: compact Cd·A 0.6 m², Crr 0.012; SUV 1.2 m², 0.017).
  • L. Guzzella and C. Onder, Introduction to Modeling and Control of Internal Combustion Engine Systems, 2nd ed., Springer (2010), §2.5: pumping loss about 0.9 bar for a petrol engine and 0.1-0.2 bar for a diesel at zero load; diesel efficiency factor at most about 0.46.
  • Engineering ToolBox, Fuels: higher and lower calorific values (read 22 Nov 2026): diesel 42.6 MJ/kg, 0.846 kg/L. Wiratkasem and Pattana, Energy Reports 7 (2021) 248: motorcycle tyre rolling resistance 8.9-13.7 N/kN.
  • Energy Saving Trust (UK), efficient driving: change up early, usually by around 2,000 rpm. IDAE (Spain), Manual de Conducción Eficiente (2006): change gear at 2,000-2,500 rpm in petrol engines and 1,500-2,000 rpm in diesels. Natural Resources Canada, fuel-efficient driving techniques; fueleconomy.gov, driving more efficiently; PCRA tips via Vikaspedia (read 17 Nov 2026).
  • UN ECE Regulation No. 39 (speedometers): the indicated speed must never be below the true speed.
  • Skill-Lync, scripts/verify/gear_speed.py (NumPy): 48 checks. Engine rpm from wheel revolutions per km, torque by numpy.interp, fuel from a per-cycle energy balance, top speed per gear by a dense scan, best gear by brute force, and the speed-vs-gear post's Swift rpm table and road load. The page recomputes every one at build time.
Free counselling

From gear ratios to powertrain engineering.

Road load, gearing and engine maps are where every powertrain and vehicle-performance role starts. A Skill-Lync counsellor can map the course that fits your branch, year and the roles you want.

Talk to a powertrain course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.