IC engine performance test calculator
Type in the readings from an engine load test and get the whole results table: torque and brake power, fuel flow, BSFC, brake thermal efficiency, BMEP, volumetric efficiency and air-fuel ratio. It also finds friction power from a Willans line, which gives indicated power, mechanical and indicated thermal efficiency and IMEP. It works out the heat balance sheet too. A second mode does the Morse test on a multi-cylinder engine. Free, no sign-up, runs in your browser.
It opens on the worked example from Skill-Lync's engine performance parameters guide: a Kirloskar 5 HP single-cylinder diesel (80 × 110 mm, 1,500 rpm) on a rope brake with a 20 mm air orifice, the engine on many Indian thermal engineering lab lists.
Load test · Willans line · heat balance · Morse test · checked against an independent script (5,116 checks at build) · Heywood ch. 2 definitions · Updated 22 Nov 2026
Readings are what you write in the lab record: the net brake load (or torque, or the generator's volts and amps), the seconds taken to burn x cc of fuel from the burette, and the manometer difference across the air-box orifice. Change any number and everything updates.
- Swept volume 552.9 cc. Highest load: 3.7 kW at 23.5 N·m, BMEP 5.35 bar, BSFC 278 g/kWh, brake thermal efficiency 30.1%.
- Willans line: fuel = 0.1979 × BP + 0.2985 kg/h over 5 readings (R² = 0.9998), so FP = 1.508 kW.
- At the highest load the indicated power is 5.21 kW and the mechanical efficiency 71.0%; indicated thermal efficiency 42.3%.
- Heat balance at reading 5: brake power 30.1%, cooling water 30.6%, exhaust 22.0%, unaccounted 17.4%.
Results for every reading
| # | Torque (N·m) | BP (kW) | Fuel (kg/h) | BSFC (g/kWh) | η brake th. | BMEP (bar) | IP (kW) | η mech. | η ind. th. | IMEP (bar) | η vol. | A/F | λ |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 0 | 0.000 | 0.297 | - | 0.0% | 0.00 | 1.508 | 0.0% | 42.4% | 2.18 | 83.8% | 82.6 | 5.65 |
| 2 | 5.886 | 0.925 | 0.483 | 523 | 16.0% | 1.34 | 2.433 | 38.0% | 42.0% | 3.52 | 83.0% | 50.2 | 3.44 |
| 3 | 11.77 | 1.849 | 0.661 | 357 | 23.3% | 2.68 | 3.357 | 55.1% | 42.4% | 4.86 | 83.0% | 36.7 | 2.52 |
| 4 | 17.66 | 2.774 | 0.854 | 308 | 27.1% | 4.01 | 4.282 | 64.8% | 41.8% | 6.20 | 82.2% | 28.2 | 1.93 |
| 5 | 23.54 | 3.698 | 1.027 | 278 | 30.1% | 5.35 | 5.206 | 71.0% | 42.3% | 7.53 | 81.4% | 23.2 | 1.59 |
| Heat balance, reading 5 | kJ/min | kW | % |
|---|---|---|---|
| Heat in the fuel | 738.4 | 12.306 | 100.0% |
| Brake power | 221.9 | 3.698 | 30.1% |
| Cooling water | 225.7 | 3.762 | 30.6% |
| Exhaust gas | 162.2 | 2.703 | 22.0% |
| Unaccounted | 128.6 | 2.143 | 17.4% |
Morse test results
| Cylinder | BP with it cut (kW) | Its indicated power (kW) |
|---|---|---|
| 1 | 15.20 | 6.80 |
| 2 | 15.50 | 6.50 |
| 3 | 15.00 | 7.00 |
| 4 | 15.40 | 6.60 |
How to use the engine performance calculator
- Describe the engine. Four- or two-stroke, number of cylinders, bore and stroke. These give the swept volume, which BMEP and volumetric efficiency are measured against.
- Pick how the engine is loaded. A rope brake needs the net load W − S in kg and the effective radius, half of the drum diameter plus the rope diameter. An eddy-current or hydraulic dynamometer reads torque directly. A generator-loaded engine needs volts, amps and the generator's efficiency.
- Enter the fuel. Labs time how long the engine takes to burn a fixed volume (often 10 cc) from a burette. Give the fuel's density and lower calorific value. The defaults for diesel are 0.830 kg/L, inside the BS-VI range on HPCL's specification, and 43,146 kJ/kg, from the US DOE's figure per gallon.
- Enter the air measurement if your rig has an air box with an orifice and a U-tube water manometer: orifice diameter, its discharge coefficient (the VTU and IARE lab manuals use 0.62, Annamalai University's 0.6; use your rig's) and the room temperature and pressure.
- Type one row per load, from no load to full load, at the same speed. The results table fills in for every row, and the Willans line is fitted through all of them.
- For the heat balance, give the reading number (usually full load), the cooling water flow and its inlet and outlet temperatures, the exhaust temperature and the exhaust gas cp.
Engine performance formulas used
Brake power is the power at the crankshaft, measured by the brake. N is in rpm, T in N·m:
Fuel flow, BSFC and brake thermal efficiency. x cc burnt in t seconds, density ρf in kg/L, lower calorific value in kJ/kg:
Mean effective pressure is the work per cycle divided by the swept volume. It lets you compare engines of any size. k is the number of revolutions per cycle:
Indicated power is what the gas does on the pistons. Friction power FP is the gap between that and brake power:
Air flow and volumetric efficiency. The manometer reads hw mm of water across an orifice of diameter do; R = 287.05 J/kg K for air:
Volumetric efficiency here is measured against room air density, the usual lab and textbook convention. For diesel the default stoichiometric A/F is 14.6 (a C₁₂H₂₃ surrogate); for petrol, 14.7. λ above 1 means lean, and diesels always run lean.
Worked example: load test on a 5 HP diesel
These are the readings from the guide: net rope-brake load 0 to 12 kg on a 0.20 m radius, the time to burn 10 cc of diesel, and the manometer head across a 20 mm orifice. They are illustrative readings, generated from a friction power of 1.5 kW and 42% indicated thermal efficiency and then rounded the way a student writes them down. They were not taken from one particular engine.
| # | W − S | 10 cc in | hw | BP | BSFC | ηbth | ηm | BMEP | ηv |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 0 kg | 100.6 s | 53 mm | 0.000 kW | - | 0.0% | 0.0% | 0.00 bar | 83.8% |
| 2 | 3 kg | 61.8 s | 52 mm | 0.925 kW | 523 g/kWh | 16.0% | 38.0% | 1.34 bar | 83.0% |
| 3 | 6 kg | 45.2 s | 52 mm | 1.849 kW | 357 g/kWh | 23.3% | 55.1% | 2.68 bar | 83.0% |
| 4 | 9 kg | 35 s | 51 mm | 2.774 kW | 308 g/kWh | 27.1% | 64.8% | 4.01 bar | 82.2% |
| 5 | 12 kg | 29.1 s | 50 mm | 3.698 kW | 278 g/kWh | 30.1% | 71.0% | 5.35 bar | 81.4% |
At full load the engine gives 3.70 kW from 12.31 kW of fuel, so its brake thermal efficiency is 30.1% and its BSFC 278 g/kWh. At quarter load the BSFC is 523 g/kWh and the mechanical efficiency only 38.0%. The friction power is roughly the same at every load, so at light load it eats most of the indicated work. That is why engines are most economical near full load. The full-load BMEP of 5.35 bar is typical of a slow naturally aspirated diesel. The engine burns at λ = 1.59, with plenty of excess air even at full load.
Friction power by the Willans line
A diesel engine's load is set by how much fuel is injected per cycle. At constant speed, fuel flow is close to a straight line against brake power. Extend that line back to zero fuel and it crosses the power axis at −FP: the brake power you would have to supply to turn the engine with no fuel burning. On the worked example the least-squares line is fuel = 0.1979 × BP + 0.2985 kg/h, which gives FP = 1.508 kW.
The generator preset shows how close the method gets. Its readings were generated from FP = 1.5 kW, rounded to 0.1 s, and the line recovers 1.48 kW. Long extrapolations are a different story. Fit only readings 3 to 5 of the worked example (half load and above) and FP comes out at 1.51 kW instead of 1.51 kW. Always include no-load and light-load points.
Use the Willans line for diesel (CI) engines only. A petrol engine is throttled, so its pumping loss changes with load and the fuel line is not straight. Measure its friction power with the Morse test or a motoring test. Even on a diesel, the line bends near full load, where combustion gets less complete. The method also assumes friction stays the same as the load changes. Annamalai University's lab manual notes that the slope rising rapidly at high load shows combustion efficiency falling. VSSUT's lecture notes call the long extrapolation from light-load data the method's main drawback.
Morse test for a multi-cylinder engine
Run the engine at a fixed speed and load and note the brake power. Cut one cylinder (short its spark plug, or cut its injector) and reduce the dynamometer load until the speed returns. The brake power falls by that cylinder's indicated power, because friction at the same speed is assumed unchanged. Repeat for each cylinder:
The preset is an illustrative four-cylinder petrol engine at 3,000 rpm: 22.0 kW with all cylinders firing, and 15.2, 15.5, 15.0, 15.4 kW with cylinders 1 to 4 cut. That gives indicated powers of 6.8, 6.5, 7.0, 6.6 kW, 26.9 kW in all, so FP = 4.9 kW and the mechanical efficiency is 81.8%. With 7.8 kg/h of petrol the brake thermal efficiency is 23.4%. As a side effect, the test shows a weak cylinder: one more than 15% below the mean gets flagged. The test is approximate. Cutting a cylinder can change the mixture reaching the others and the pumping loss, and the method assumes both stay the same.
Heat balance sheet
A heat balance follows the fuel's energy to where it ends up. Most labs work it per minute:
On the worked example at full load, with this page's illustrative heat readings (4.5 kg/min of cooling water heated from 28 to 40 °C, exhaust at 400 °C), the split is:
| Heat | kJ/min | % |
|---|---|---|
| Supplied by the fuel | 738.4 | 100.0% |
| Brake power | 221.9 | 30.1% |
| To the cooling water | 225.7 | 30.6% |
| In the exhaust gas | 162.2 | 22.0% |
| Unaccounted (radiation, oil, errors) | 128.6 | 17.4% |
Friction power doesn't get its own line. The heat it makes leaves through the cooling water and the oil, so the sheet balances on brake power. The exhaust term uses the air flow from the orifice plus the fuel flow. The calculator takes cpg = 1.05 kJ/kg K by default, the value for air at about 600 K. Many Indian lab manuals (IARE, Annamalai University) use 1.005 kJ/kg K, air at room temperature, which gives about 4% less exhaust heat; type whichever your manual uses. Rigs with an exhaust gas calorimeter, like the one in VTU's manual, find mgcpg from the calorimeter's water flow and temperature rise instead. If you have that reading, use it in place of the formula. Cooling water uses cpw = 4.18 kJ/kg K.
BSFC and efficiency: the same number two ways
| Brake thermal efficiency | BSFC on diesel (43,146 kJ/kg) | BSFC on petrol (43,431 kJ/kg) |
|---|---|---|
| 25% | 334 g/kWh | 332 g/kWh |
| 30% | 278 g/kWh | 276 g/kWh |
| 35% | 238 g/kWh | 237 g/kWh |
| 40% | 209 g/kWh | 207 g/kWh |
| 45% | 185 g/kWh | 184 g/kWh |
So a quoted BSFC tells you the efficiency, as long as you know which calorific value was used. With the higher calorific value, which includes the latent heat of the water in the exhaust, the same engine looks about 7% less efficient on diesel. This page and most engine data use the lower value.
What this calculator does not cover
- Correcting power to standard reference conditions. Rated power is quoted at standard air conditions (IS 10000 Part 2, ISO 1585, SAE J1349); a lab test reports what the engine gave that day.
- Indicated power from an indicator diagram or a pressure transducer: if you have a measured IMEP, use "A value I know" with FP = IP − BP.
- Motoring and retardation tests, the other ways of measuring friction power.
- Variable-speed tests (torque and power curves against speed). The Willans line needs constant speed; the results table itself works at any speed.
- Emissions and smoke (g/kWh of NOx, PM, opacity), and supercharged engines' boost and intercooling.
Industry engine teams model these same quantities, BMEP, BSFC, volumetric efficiency and friction, in 1D tools like GT-POWER before an engine is built. Skill-Lync's IC engine courses teach that workflow.
Frequently asked questions
How do you calculate the brake power of an engine in a lab test?
Brake power is BP = 2πNT/60,000 kW, with N in rpm and T in N·m. On a rope brake, T = (W − S) × g × (drum diameter + rope diameter)/2. A net load of 12 kg on a 0.20 m effective radius at 1,500 rpm gives 23.54 N·m and 3.70 kW.
What is BSFC and what is a good value?
Brake specific fuel consumption is the fuel burnt per unit of brake work, in g/kWh: fuel flow ÷ brake power. It is the inverse of brake thermal efficiency: on diesel (LCV 43,146 kJ/kg) 30% efficiency means 278 g/kWh and 40% means 209 g/kWh. It rises steeply at light load, where friction takes most of the work.
How do you find friction power with a Willans line?
Run a diesel engine at constant speed at several loads, plot fuel flow against brake power and extend the straight line back to zero fuel. It crosses the power axis at −FP. On this page's worked example the line gives FP = 1.51 kW. It works for diesel engines only, because a petrol engine's throttle changes its pumping loss with load.
What is the Morse test?
A friction-power test for multi-cylinder engines. With the engine at a fixed speed, each cylinder is cut in turn and the load reduced until the speed returns. The drop in brake power is that cylinder's indicated power. Adding them gives IP, and FP = IP − BP. The example engine gives 26.9 kW indicated, 4.9 kW friction, 81.8% mechanical efficiency.
How do you calculate volumetric efficiency from an orifice meter?
Turn the water-manometer head into a head of air (h_w × ρ_water/ρ_air), get the air flow from V = Cd × orifice area × √(2gH), and divide by the swept-volume rate, Vd × N/120 for a four-stroke. With a 20 mm orifice, Cd 0.62 and 50 mm of water, the 553 cc example engine breathes 81.4% of its swept volume.
What goes into a heat balance sheet of an IC engine?
The heat in the fuel (fuel flow × LCV) split into brake power, heat carried away by the cooling water (flow × 4.18 × temperature rise), heat in the exhaust gas (air + fuel flow × cp × exhaust minus room temperature) and the unaccounted rest: radiation, lubricating oil and errors. Labs usually write it per minute, in kJ/min, and as a percentage.
Related on Skill-Lync
- Performance parameters of an IC engine (the guide this example comes from)
- Thermal Engineering interactive book: engine testing (Morse and Willans interactives)
- Otto, Diesel and dual cycle calculator (the ideal-cycle limit for these engines)
- Adiabatic flame temperature calculator
- Stages of combustion in CI engines
- Does a diesel engine make more torque than a petrol engine?
- IC engine and combustion courses
- All free engineering tools
Sources
- J. B. Heywood, Internal Combustion Engine Fundamentals, ch. 2 "Engine design and operating parameters" (McGraw-Hill), the definitions as given in UNC Charlotte's MEGR 3210 equation sheet: "bmep = Pb/(Vd N/n), n = number of crank revolutions per cycle", "ηfc = Pb/(ṁf QLHV)", "ηv = ṁa/(ρa Vd N/n), ρa can be atmospheric or intake air density, must be specified", "bsfc = ṁf/Pb"; and NIT Srinagar MSD 302 lecture 4, which teaches from Heywood: "nR is the number of crank revolutions for each power stroke per cylinder (two for four-stroke cycles; one for two-stroke cycles)". Read 22 Nov 2026.
- VTU BAEL504 Energy Conversion Lab Manual, ACS College of Engineering: rope brake "T = 9.81(W−S)(D+d)/2", fuel "mf = (10 cc/1000)(1/t) × sp. gravity", orifice "Vact = Cd √(2gH) πd²/4", "Cd → 0.62", "ρair → P/RT", volumetric efficiency against "Vth = (πD²/4) L N/(2 × 60)", heat balance "q2 = mw cpw (Two − Twi)", "q4 = Q − (q1 + q2 + q3)", exhaust by calorimeter. Read 22 Nov 2026.
- IARE, Thermal Engineering Lab Manual: heat to exhaust "He = Me × Cpg × (T4 − T1)", "Cpg = specific heat of exhaust gas 1.005 kJ/kgK", "Me = Ma + TFC", "Hu = Hi − (Hb + Hw + He)", orifice Cd 0.62. Read 22 Nov 2026.
- Annamalai University, MECP607 Applied Thermal Laboratory manual: Willans line ("the amount of negative power output obtained by extrapolation of the plot at zero rate of fuel consumption represents the frictional power"; "since petrol engine is throttled ... not suitable for use with petrol engines"; slope rising at high load = falling combustion efficiency); heat balance with exhaust cp 1.005 kJ/kg K and orifice Cd 0.6. Read 22 Nov 2026.
- VSSUT, IC engine lecture notes: the Morse test "is applicable only to multicylinder engines", one cylinder cut by shorting the plug or disconnecting the injector at constant speed, "liable to errors due to changes in mixture distribution"; Willans line's "main drawback ... the long distance to be extrapolated". Read 22 Nov 2026.
- Annamacharya University, Thermal Engineering Lab equipment list (Jan 2026): four-stroke single-cylinder Kirloskar diesel, 5 HP, 1,500 rpm, bore 80 mm, stroke 110 mm, CR 16.5, 20 mm orifice, rope brake loading; experiments: load test and heat balance test.
- US DOE Alternative Fuels Data Center, Fuel Properties Comparison: diesel lower heating value 128,488 Btu/gal (higher 138,490), gasoline up to 116,090 Btu/gal. Converted at 0.830 and 0.745 kg/L.
- Hindustan Petroleum, MS and HSD BS-VI specifications: diesel density 810-845 kg/m³ and petrol 720-775 kg/m³ at 15 °C.
- Bureau of Indian Standards, IS 10000 (Part 2):1980, "Methods of tests for internal combustion engines, Part 2: standard reference conditions".
- Engineering ToolBox, Air: specific heat at constant pressure: cp 1.051 kJ/kg K at 600 K (1.006 at 300 K). Read 22 Nov 2026.
- Skill-Lync, Performance parameters of an IC engine (refreshed 18 Nov 2026): the worked example's readings and its published results (BP 3.70 kW, FP 1.51 kW, BSFC 278 g/kWh, BMEP 5.35 bar, IMEP 7.53 bar, ηv 81.4%, A/F 23.2), which this page reproduces.
- Skill-Lync, scripts/verify/engine_test.py: works every quantity a different way (BMEP from work per cycle, volumetric efficiency on a mass basis, the Willans line by exact-fraction normal equations, Morse friction as (n − 1)·BPall − ΣBPcut) over the presets and 80 random cases. The page compares 5,116 numbers with it when it is built.