WOT drive cycle calculator: grade, wind, top speed and MPGe

Set the vehicle, the road grade and the wind the way the Powertrain Blockset environment block reads them, and see the full-throttle run: whether it reaches the target speed, how long it takes, the top speed it levels off at, the road load at the target and the energy and MPGe of the run.

Vehicle Body 3DOF conventions · checked by a separate solver · 885 student reports read · Updated 20 Nov 2026

Mass, Cd, frontal area, air pressure and temperature are the Vehicle Body 3DOF block defaults; the motor, ratio, tyre and efficiencies are assumed, because MathWorks does not publish the reference applications' vehicle data. Full-throttle time = deceleration time minus start time.

Time to targetnot reachedlevels off at 37.6 m/s
Top speed37.6 m/s135 km/h
Energy740 Wh/km28.3 MPGe over the run
Vehicle speed against time at full throttle, flat road and still air compared with the chosen grade and wind0102030405060010203040506070time (s)speed (m/s)target 50 m/s

this grade and windflat road, still airtarget

    Force at the target speedNkW at the wheel

    What does the WOT condition challenge ask?

    Run MathWorks' HEV reference application with the wide-open-throttle (WOT) drive cycle, change the grade and the wind velocity in its environment block, comment on the results, then compare hybrid and pure-electric powertrains. Along the way it asks how mapped and dynamic engine, motor and generator models differ and how the model computes miles per gallon.

    It is the Week 4 challenge of Skill-Lync's Introduction to Hybrid Electric Vehicle using MATLAB and Simulink, and Skill-Lync read all 885 distinct public reports (928 pages) on 20 Nov 2026. 376 state the grade and wind they ran. This calculator does the part that can be checked by hand: what a grade and a wind actually do to a full-throttle run, and how MPGe is computed.

    Is the grade in the environment block in degrees or percent?

    Degrees. The Vehicle Body 3DOF Longitudinal block, which the environment block feeds, takes the "road grade angle, γ, in deg", and 11 reports quote the field as Grade (deg). So typing 5 makes a 5° slope, which is 8.75%, not 5%. Road signs and gradeability figures use percent:

    163 reports call their grade degrees. About 21 describe the number they typed as a percentage (Grade = 10%, 7% gradeability; Skill-Lync checked each by hand), so the model ran a steeper slope than the report states: 10 typed is 10° = 17.6%. One report scripted set_param(..., 'Grade', '0.05') for a "5% grade", which is a 0.05° slope, almost flat. On the 1,200 kg block-default car the difference between 5° and 5% is a force:

    In the mid-size example below, the WOT run reaches 50 m/s in 32.8 s on a 5% grade but takes 71.7 s on a 5° grade.

    Is a positive wind velocity a headwind or a tailwind?

    A headwind. MathWorks' documentation: "Positive wind speed is a headwind that opposes vehicle motion and increases drag." Drag is computed from the vehicle speed plus the wind speed, so a 10 m/s wind at 50 m/s acts like 60 m/s of air, and drag grows with the square:

    That is 44% more drag; a 10 m/s tailwind (type −10) cuts it to 621 N. The reports mostly get the direction right: 91 describe the wind as opposing the car or adding drag, 6 describe a tailwind, and 24 typed a negative wind. Air density in the block is not a parameter; it is P/(RT) from the ambient pressure and temperature (defaults 101,325 Pa and 273 K, 1.293 kg/m³ with R = 287.05 J/kg·K).

    How much do grade and wind slow a WOT run?

    A lot more than the force numbers suggest, because at full power the motor's wheel force falls as 1/v. For the 80 kW block-default example, a 5° grade drops the top speed from 56.3 to 41.8 m/s, so it never reaches the 50 m/s target, and a 10 m/s headwind alone leaves it just short within 75 s.

    The calculator integrates the longitudinal equation of the Vehicle Body 3DOF block (rolling resistance as a constant Crr; the reference application computes it in its Longitudinal Wheel block) with full motor torque up to base speed and full power above it:

    Environment80 kW car150 kW car
    Top speed (m/s)Time to 50 m/s (s)Wh/kmTop speed (m/s)Time to 50 m/s (s)
    Flat, still air56.334.547167.222.5
    5° grade41.8> 7568550.771.7
    5% grade (2.86°)47.8> 7561357.532.8
    10 m/s headwind50.1> 7558060.925.9
    10 m/s tailwind (−10)63.027.736973.820.6
    5° grade + 10 m/s headwind37.6> 7574046.3> 75
    10° grade + 25 m/s headwind24.4> 751,07031.1> 75

    75 s at full throttle from rest (the 5 s to 80 s window the course's reference application uses, as reports describe it), target 50 m/s. 80 kW car: block defaults + assumed 80 kw motor (1200 kg, Cd 0.3, 2 m², 250 N·m). 150 kW car: 1800 kg, Cd 0.28, 2.4 m², 350 N·m, all assumed. Energy counts motor power only, at 0.95 × 0.9 efficiency, and no regeneration.

    155 reports use words like "could not reach" or "unable to follow" about the target speed. That is the expected result, not a model fault: the target in a WOT cycle is set high on purpose so the driver model stays at full accelerator.

    Why does the speed creep towards its top speed and never quite get there?

    Because the net force shrinks to zero as the speed approaches the top speed, so the last metre per second takes longer and longer. In the 80 kW example with a 10 m/s headwind the top speed is 50.08 m/s, just above the target, yet after 75 s the car is at 49.74 m/s. When a report's trace flattens just under the target, check the top speed before blaming the controller.

    How is MPGe calculated, and why does the plot spike?

    MPGe is miles per gallon-equivalent: the EPA counts 33.705 kWh of electricity as one US gallon of gasoline (the window sticker rounds it to 33.7). Divide that by the energy the car uses per mile:

    503 reports quote 33.7 and 5 the exact 33.705; the difference is 0.015%. The reference application computes it second by second from vehicle speed and battery power, so the trace is a ratio:

    When battery power passes through zero, as the driver lifts off or regeneration begins, the ratio shoots towards infinity and then turns negative; 18 reports remark on the spikes. The meaningful number is the trip value: total distance over total energy. The full-throttle run itself is a poor efficiency test: the 80 kW example uses 471 Wh/km (44.5 MPGe) on the flat at up to 180 km/h.

    What this calculator does not cover

    • The engine, gearbox and controller of the HEV. It models one motor with a torque and power limit; the reference application's engine, generator, power split and SOC-based supervisory controller are not modelled, so hybrid runs will differ.
    • Tyre slip and load transfer. The 3DOF block computes axle loads and pitch; here the wheel force is never grip-limited (see the gradeability calculator for the grip limit).
    • Battery limits. Voltage sag, current limits and SOC are not modelled; energy is motor power over the run.
    • The exact WOT speed profile. The run starts at full throttle from rest and holds the target once reached, as an ideal driver would.
    Learn HEV modelling

    Reading a simulation result against a hand calculation, and knowing which block holds which assumption, is what this challenge trains. It is part of Skill-Lync's hybrid vehicle courses.

    Frequently asked questions

    Is the grade in the Powertrain Blockset Environment block in degrees or percent?

    Degrees. The Vehicle Body 3DOF Longitudinal block takes the road grade angle γ in degrees, and the environment block in the reference applications labels it Grade (deg). Typing 5 gives a 5° slope, which is 8.75%. For a 5% grade type 2.86.

    Is a positive wind velocity a headwind or a tailwind in Simulink?

    A headwind. MathWorks' Vehicle Body 3DOF Longitudinal documentation says a positive wind speed is a headwind that opposes vehicle motion and increases drag; the drag force uses the vehicle speed plus the wind speed. Type a negative number for a tailwind.

    What is the WOT drive cycle in Powertrain Blockset?

    Wide open throttle: the Drive Cycle Source block holds an initial speed, then asks for a high nominal speed from a start time until a deceleration time, so the driver model saturates at full accelerator. The defaults are 0 to 30 m/s from 5 s to 20 s in a 30 s run; in the course's runs, as the reports describe them, it is 50 m/s.

    How is MPGe calculated?

    Divide 33.705 kWh, the electricity the EPA counts as one US gallon of gasoline (33.7 on the window label), by the energy used per mile. A car using 200 Wh/km uses 0.322 kWh per mile, so it gets 104.7 MPGe. The reference application does it second by second from battery power and speed.

    Why does the MPG or MPGe plot spike in the reference application?

    Because the instantaneous value is speed divided by power. When the battery power passes through zero, as the driver lifts off or regeneration starts, the ratio becomes huge and then negative. Read the trip value (distance over total energy), not the instantaneous trace.

    Why can't the vehicle reach the WOT target speed on a grade?

    Because at full power the wheel force falls as P/v, while the grade adds a constant force and drag grows with the square of the air speed. Where the two curves cross is the top speed. In this page's 80 kW example a 5° grade drops it from 56.3 to 41.8 m/s, below the 50 m/s target.

    Is this calculator accurate?

    For the longitudinal force balance, yes: a separate Python script integrates every run with a different method and step, finds the top speed by Newton's method instead of bisection, and checks the integrator against three exact solutions; the page's numbers agree within 0.01% (energy within 0.2%). It does not model the reference application's engine, gearbox or controller.

    Related on Skill-Lync

    Sources

    • MathWorks, Vehicle Body 3DOF Longitudinal block reference (Vehicle Dynamics Blockset / Powertrain Blockset): drag ½ (Pabs/RT) Cd Af (ẋ + wx)², "Positive wind speed is a headwind that opposes vehicle motion and increases drag", grade "road grade angle, γ, in deg", defaults 1,200 kg, 2 m², Cd 0.3, 101,325 Pa, 273 K. Vehicle Body 1DOF Longitudinal: m ẍ = FxF + FxR − Fd,x − m g sin γ; "Negative wind speed is a tailwind".
    • MathWorks, Drive Cycle Source block reference: Wide Open Throttle (WOT) parameters and defaults (start 5 s, 0 to 30 m/s, deceleration at 20 s, 30 s run). Longitudinal Driver block: speed-tracking controller with accelerator and brake commands normalised 0 to 1.
    • MathWorks, Build Electric Vehicle / HEV P2 / HEV Multimode reference application pages: the Environment subsystem "implements the environment model, including road grade, wind velocity, and ambient temperature and pressure". No vehicle data or MPGe constant is published there.
    • 40 CFR 600.002 (eCFR): "one gallon of gasoline is equivalent to 33.705 kilowatt-hours of electricity"; fueleconomy.gov label: 33.7 kWh per gallon. NIST Handbook 44 (2026) Appendix C: 1 mile = 1.609344 km, 1 US gallon = 3.785411784 L.
    • Skill-Lync, all 885 public WOT condition reports, read 20 Nov 2026: grades, winds, units, the MPGe constant and conclusions.
    • Skill-Lync, scripts/verify/wot.py: re-integrates every run with Heun's method at a 10x finer step, solves top speed by Newton's method, checks the integrator against exact solutions for constant force, torque-then-constant-power and torque with quadratic drag, and checks 30 random vehicles.
    Free counselling

    From a Simulink trace to a powertrain decision.

    HEV and EV teams want engineers who can run a reference model, explain every curve with a force balance and size the motor and battery from it. A Skill-Lync counsellor can map the course that fits the role you want.

    Talk to an HEV course counsellor

    Free. We call you back, usually the same day.

    By submitting you agree to our Terms and Privacy Policy.

    Talk to a career counsellor

    Talk to a career counsellor

    Free 20-minute call. We'll map the right course to where you want to work.

    By submitting you agree to our Terms and Privacy Policy.