Planetary gear simulator and ratio calculator
Set the sun and planet tooth counts, hold one member and drive another, and watch the gear set turn. You get the ratio, every member's speed and torque, the planet spin and a check that the planets actually fit. Drive two members at once to see how a hybrid car's power split device works. Free, no sign-up.
Willis equation · 6 configurations + two-input mode · teeth drawn in true mesh · verified by script · Updated 16 Nov 2026
Enter 0 rpm to hold a member. Give the other two members any speeds to model a power split.
- OK Ring = sun + 2 × planet: 24 + 2 × 24 = 72
- OK Teeth line up: (24 + 72) / 3 = 32
- OK Planets clear each other (adjacency)
- OK No undercut: sun and planet ≥ 17 teeth
| Member | Speed (rpm) | Torque (N·m) | Power (W) |
|---|---|---|---|
| Sun | 1,500 | 10 | 1,571 |
| Carrier | 375 | -40 | -1,571 |
| Ring | 0 | 30 | 0 |
| Each planet (spin) | -750 | -1,125 rpm relative to carrier | |
Tangential force at each sun–planet mesh: 138.9 N, if the 3 planets share the load equally. Positive power flows into the gear set; the powers add to zero because losses are ignored.
The three speeds always sit on one straight line.
The carrier axis sits Zr : Zs of the way from sun to ring, so the carrier speed is a weighted average of the other two. Change any speed above and watch the line pivot.
How do you calculate a planetary gear ratio?
Use the Willis equation. It links the speeds of the sun, ring and carrier through just two tooth counts. Hold one member (speed zero), drive another, and solve for the third. With the ring held and the sun driving, the ratio is one plus the ring-to-sun tooth ratio, so a 24-tooth sun inside a 72-tooth ring gives 4:1.
Seen from the carrier, the set is an ordinary gear train: sun to planet to ring, with the planets as idlers, so the ratio is −Zr/Zs. Multiplying out gives the form this simulator uses, which treats all three members alike:
At 1,500 rpm on the sun the carrier turns at 375 rpm in the same direction. The planet tooth count Zp drops out of every ratio. It sets the size of the set and the planet's own spin:
Each planet spins at -750 rpm, backwards, as it rolls around the inside of the ring. That is -1125 rpm relative to the carrier, the speed its bearing sees.
What are the 6 ways to use a planetary gear set?
Hold any one of the three members and use the other two as input and output: 3 × 2 = 6 single-speed configurations. Two give reductions, two give overdrives and two reverse the direction. Here they are for the 24/24/72 example with 1,500 rpm and 10 N·m in, losses ignored.
| Held | Input | Output | Ratio | Output speed | Output torque | Use |
|---|---|---|---|---|---|---|
| Ring | Sun | Carrier | 4 | 375 rpm | 40 N·m | Reduction, same direction. The most common layout: the reducer in gearmotors, robot joints and hub drives. |
| Ring | Carrier | Sun | 0.25 | 6,000 rpm | 2.5 N·m | Overdrive, same direction: the output turns faster with less torque. |
| Sun | Ring | Carrier | 1.333 | 1,125 rpm | 13.33 N·m | Small reduction, same direction. |
| Sun | Carrier | Ring | 0.75 | 2,000 rpm | 7.5 N·m | Small overdrive, same direction: the classic overdrive stage in older automatic gearboxes. |
| Carrier | Sun | Ring | -3 | -500 rpm | -30 N·m | Reduction with reversed direction: an ordinary gear train whose idlers are the planets. |
| Carrier | Ring | Sun | -0.333 | -4,500 rpm | -3.33 N·m | Speed increase with reversed direction. |
A negative ratio means the output turns the other way. Automatic gearboxes get several speeds out of one or two planetary sets by using clutches and brakes to change which member is held and which is driven. Locking any two members together makes the whole set turn as one, at 1:1.
How many teeth can a planetary gear set have?
You can't pick any three numbers. With standard gears of one module, three rules decide whether the set can be built, and the simulator checks all of them:
- Ring = sun + 2 × planet. The planet has to span the gap between sun and ring.
- Assembly condition. For N equally spaced planets to mesh with both the sun and the ring at once, the sum of sun and ring teeth must divide by N.
- Adjacency condition. Neighbouring planets must not touch: their centre distance has to exceed one planet tip diameter (Zp + 2 modules).
For 24/24/72: 2, 3 or 4 planets work. Five planets clear each other, but (24 + 72)/5 = 19.2 is not a whole number, so the fifth planet's teeth would land on the ring's teeth. Six planets collide. Set N to 5 in the simulator and watch the teeth overlap.
A fourth rule applies to small gears: with 20° full-depth teeth, fewer than about 17 teeth on the sun or a planet means the cutter undercuts the tooth root, unless the gear is profile-shifted.
How much torque does each member carry?
For the set to be in balance, the torques on the three members must add up to zero, in the same proportion as the tooth counts. The carrier always carries the largest torque, the sum of the other two. With 10 N·m on the sun, the ring has to be held with 30 N·m and the carrier delivers 40 N·m.
That torque is shared between the planets, which is why planetary gearboxes are compact: three planets mean three meshes carrying the load. The force on each sun–planet mesh, assuming equal sharing:
Power is torque times speed: 1,571 W goes in at the sun and the same comes out at the carrier. Real planets never share load perfectly (manufacturing errors make one planet carry more), so gear standards apply a load-sharing factor greater than one when sizing the teeth.
How does the Toyota Prius power split device work?
The Prius uses one planetary gear set with nothing held. The engine drives the carrier, the generator sits on the sun, and the traction motor and wheels are on the ring. Oak Ridge National Laboratory's teardown of the 2004 Prius counted a 78-tooth ring and a 30-tooth sun. With Zs = 30 and Zr = 78, the Willis equation becomes:
- Engine start, car stopped: ring at 0, generator spins the sun at 3,600 rpm, and the carrier cranks the engine at 1,000 rpm.
- Cruising: engine at 2,000 rpm, motor at 3,000 rpm: the generator turns at -600 rpm. By changing the generator speed, the car runs the engine at any speed it wants for a given road speed. This is the "electronic CVT".
- Engine off, car moving: carrier at 0, motor at 2,000 rpm: the generator spins backwards at -5,200 rpm. ORNL lists the generator's top speed as 10,000 rpm.
Press "Prius power split" in the simulator to try your own speeds. One honest wrinkle: the report's figure shows 23-tooth pinions, but 30 + 2 × 23 = 76, not 78. Either the pinions are profile-shifted or the figure is off. It doesn't matter for the speeds, which depend only on the sun and ring, so the simulator draws 24-tooth pinions to keep the drawing standard.
What this simulator does not cover
- Losses. Torques and powers are ideal. Real stages lose a few percent to tooth friction, bearings and oil churning, so the output torque is lower than shown.
- Profile-shifted, stepped or compound planets (Ravigneaux and Simpson sets, double-planet carriers). The drawing assumes standard teeth with Zr = Zs + 2Zp; a double-planet set changes the sign in the Willis equation.
- Tooth strength and life. The tangential force is a starting point for a bending or contact-stress check (Lewis, ISO 6336, AGMA 2001), not a substitute for one.
- Unequal planet spacing. Sets that fail the assembly condition can still be built with planets at unequal angles; the simulator spaces them equally and flags the clash.
Model a planetary gear train in SOLIDWORKS and run its motion study, or model a hybrid transmission in Simulink, in a Skill-Lync course.
- Multibody Dynamics using SolidWorks (5 weeks; week 3: design and MBD simulation of a planetary gear train)
- Development of Hybrid Drives using MATLAB and Simulink (12 weeks; week 7: transmissions, including planetary gear sets)
- Post Graduate Program in Hybrid Electric Vehicle Design and Analysis (48 weeks)
Frequently asked questions
How do you calculate the gear ratio of a planetary gear set?
Use the Willis equation, Zs·ωs + Zr·ωr = (Zs + Zr)·ωc, with the held member's speed set to zero. With the ring held, sun in and carrier out, the ratio is 1 + Zr/Zs: a 24-tooth sun and 72-tooth ring give 4:1. The planet tooth count does not appear in the ratio.
Does the number of planet gears change the ratio?
No. The ratio depends only on the sun and ring tooth counts. More planets share the load, so each mesh carries less force (here 138.9 N per planet with 3 planets, 104.2 N with 4), but the planets must fit around the sun and the teeth must line up: (Zs + Zr)/N must be a whole number.
Why do the planet gears spin backwards?
With the ring held, each planet rolls around the inside of the ring, so it spins against the carrier's direction. In the 24/24/72 example the carrier turns at +375 rpm and each planet at -750 rpm absolute, -1125 rpm relative to the carrier. The planet speed matters for its bearings.
What happens if no member of a planetary gear set is held?
Nothing is transmitted: with two free members the set has two degrees of freedom, so the input just spins the free members. That is how an automatic gearbox makes neutral, and how a power split device works on purpose: two members are driven (engine and motor) and the third speed follows from the Willis equation.
What is the minimum number of teeth on a sun or planet gear?
For standard 20° full-depth teeth, about 17 (2/sin²20° = 17.1) before the cutter undercuts the root. Smaller gears are made with a positive profile shift. The calculator flags any sun or planet under 17 teeth.
Is the torque on the carrier the sum of the sun and ring torques?
Yes, ideally. For the set to be in balance, the carrier torque equals the sun torque plus the ring torque with the opposite sign: Ts : Tr : Tc = Zs : Zr : −(Zs + Zr). With 10 N·m on the sun of the example, the ring reacts 30 N·m and the carrier delivers 40 N·m, before friction losses.
Related on Skill-Lync
- All free engineering tools and calculators
- Creating a planetary gear system in SOLIDWORKS: a step-by-step guide
- Modelling and simulating a planetary gear system in SOLIDWORKS
- Building a gear transmission model in Simscape
- How do hybrid electric cars work?
- Tolerance stack-up calculator (its worked example is a gear float)
- Compare Skill-Lync's SOLIDWORKS courses
Sources
- Oak Ridge National Laboratory, Evaluation of 2004 Toyota Prius Hybrid Electric Drive System, ORNL/TM-2004/247 (interim report, revised FY 2007), section 2.2.2 and Fig. 2.4: ring gear 78 teeth, sun gear 30, pinions 23; generator speed = 2.6 × motor speed with the carrier locked; generator up to 10,000 rpm (section 2.2.3).
- R. Willis, Principles of Mechanism (1841): the relative-speed method for epicyclic trains; the assembly and adjacency conditions as given in standard machine-design texts (e.g. Shigley's Mechanical Engineering Design, gear trains).
- ISO 53:1998 standard basic rack (20° pressure angle, addendum 1 m, dedendum 1.25 m), used for the drawing and the adjacency rule; undercut limit 2/sin²α for a rack-type cutter.
- All numbers on this page: Skill-Lync, recomputed by scripts/verify/planetary.py (pure Python): ratios checked against an independent pitch-line velocity derivation, power and torque balance on 5,000 random states, and the drawing's tooth-phase rule on 14,000 random poses (teeth mesh exactly when the assembly condition holds); cross-checked against this page's simulator code at build time.