Week 10- Assembly Workbench

Aim:To find the section modulus of the hood and optimization to improve the overall section modulus. Objective:Use the section from your Hood design and calculate the section modulus using the formula S= I/y. Section Modulus:The section modulus (S) is the geometry property of the cross-section used for designing…

AIM:Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters.Introduction:Hood is also called as bonnet. It is one of the BIW part of car. It consists of inner and outer panel. Hinge system and striker. Inner panel gives strength and outer panel is cover…

OBJECTIVEThe objective of this project is to design a butterfly valve and apply GD&T to its components and final assembly using Siemens NX.INTRODUCTIONGEOMETRIC DIMENSIONING & TOLERANCE Geometrical dimension is a geometric characteristic, the size of which is specified  as length angle location or…

DOOR PANEL  AIM : To create the Door trim panel's CAD model considering the inputs such as class A surface and master section and by following the design rules and OEM standards. INTRODUCTION The door panel covers internal parts like the window regulator, the power window motor, and the wiring. In older…

  AIM: Create the part models and assembly for the given drawings below with a report. DRAWING 1 QUICK RETURN MECHANISM PART_01   PART_02 PART_03 PART_04 PART_05 ASSEMBLY_01    Quick Return Mechanism- 2D drawing Creation     DRAWING_02 CV Joint - Part design and Assembly   …

DOOR TRIM DESIGN WITH DOG HOUSE   OBJECTIVE: The main aim of this challenge is to create Dog house features of the 'Door Trim', with the help of CATIA V5. CLASS A SURFACE We get class A surface as a input. we create B surface and C surface using this class as a refference. TOOLING AXIS  To create the tooling…

DRILL HANDLE  DESIGN WITH RIBS AND SCREW BOSS AIM: Create the rib and Create the Screw boss for the Drill Handle considering the design rules. OPERATION CLASS A SURFACE We get class A surface as a input. we create B surface and C surface using this class as a refference. TOOLING AXIS  To create the…

DOOR TRIM LOWER WITH ENGINEERING FEATURES AIM:Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  OPERATIONS:…

 A-PILLER DESIGN WITH MASTER SECTION   AIM:The main objective of this challenge is to understand the given master section to create a solid body and B-side features for a given class A surface, by considering all the design parameters. OPERATIONS MASTERSECTION  We get class A surface with master section…

    AIM:Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  OPERATIONS: CLASS A SURFACE We get class A surface…

 CORE AND CAVITY DESIGN OF SWITCH BEZEL   AIM  To create the Core and cavity blocks for the Switch Bezel Component.  OBJECTIVE To Create Core and Cavity and Parting surface for the given component along the Tooling Axis.   TOOLING AXIS Extracted the base surface and center point is created by using the on surface at zero.On…

COIN HOLDER DESIGN AIM Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  OBJECTIVE : Creation of Tooling Axis.…

SWITCH BEZEL DESIGN AIM:Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  OBJECTIVE : Creation of Tooling Axis.…

REPORT ON DESIGNING OF BASE BRACKET PLASTIC COMPONENT:    AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the…