1. The major elements from the given wiring diagram are :- Battery, Generator, Distributor, Fuse, Regulator and 2. Battery :- Fuse:- Regulator :- 3. P(W)=V*I i.e. 12*10= 120W Amps=Watts/Volts i.e. 120/12= 10Amps. 4. P(W)=V*I i.e. 500= V*10 i.e. V=50V
JEFIN VARGHESE
updated on 24 Jan 2024
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by JEFIN VARGHESE (24)
Week - 2 - Explicit and Implicit Analysis
>AIMAS PER THE ARTICLE SHARED, A NON LINEAR STATIC PROBLEM IS SOLVED USING BOTH EXPLICITE AND IMPLICITE ANALYSIS. BOTH OF THE CASES USE INCREMENTAL LOAD CONTROL SCHEME AND HERE IT IS ADVISED TO USE THIS EQUATION "F(u) = u3+9u2+4u" AND SOLVE USING BOTH EXPLICITE AND IMPLICITE METHODS.ALSO TO EXPLAIN IN DETAIL ABOUT IMPLICITE…
10 Jul 2024 05:28 PM IST
Assignment 7-Side Pole Crash Simulation Challenge
AIM FOR THE GIVEN NEON SIDE CRASH BIW CHECK UNIT SYSTEM AND FOLLOW THE RELEVANT AS APPLICABLE. CREATE APPROPRIATE INTERFACE, FRICTION AND RECOMMENDED PARAMETERS. TO MAKE SURE THAT THERE ARE NO PENETRATIONS AND INTERSECTIONS. TO CREATE A RIGID POLE WITH A FRICTION OF 0.1 AS PER THE FMVSS 214 STANDARDS. TO COMPARE…
26 Feb 2024 04:06 PM IST
Assignment 6-Frontal Crash Simulation Challenge
AIM FOR THE GIVEN FRONTAL CRASH BIW CHECK UNIT SYSTEM AND FOLLOW THE RELEVANT AS APPLICABLE. CREATE APPROPRIATE INTERFACE, FRICTION AND RECOMMENDED PARAMETERS. TO MAKE SURE THAT THERE ARE NO PENETRATIONS AND INTERSECTIONS. CORRECTION OF RIGID BODIES IF NEEDED AND CREATION OF RIGID WALL WITH FRICTION AS RECOMMENDED. TO…
26 Feb 2024 04:06 PM IST
Assignment 5-RADIOSS Interfaces & Study of Effect of Notches Challenge
OBJECTIVE TO CREATE MESH FOR THE GIVEN 'BUMPER ASSEMBLY' WITH THE SPECIFIED CONDITION. TO RUN THE GIVEN 'CRASH TUBE' MODEL EACH BY CHANGING CONDITIONS AND TO COMPARE THE SAME AFTER PLOTTING ENERGY AND FORCES. PROCEDURE HYPERMESH (OPTISTRUCT)>FILE>IMPORT>MODEL>'select as needed'>IMPORT. GEOM>TEMP…
31 Jan 2024 03:47 PM IST
Project - Analysis of a practical automotive wiring circuit
1. The major elements from the given wiring diagram are :- Battery, Generator, Distributor, Fuse, Regulator and 2. Battery :- Fuse:- Regulator :- 3. P(W)=V*I i.e. 12*10= 120W Amps=Watts/Volts i.e. 120/12= 10Amps. 4. P(W)=V*I i.e. 500= V*10 i.e. V=50V
24 Jan 2024 05:49 PM IST
Assignment 4-RADIOSS Material Laws Challenge
OBJECTIVE TO COMPARE THE 7 DIFFERENT CASES GIVEN FOR THE NUMBER OF CYCLES, ENERGY ERROR, MASS ERROR AND SIMULATION TIME TO UNDERSTAND THE PROPERTY DIFFERENCES. TO PLOT ENERGIES FOR ALL THE GIVEN CASES TO NOTICE DIFFERENCES. TO ARRIVE AT A CONCLUSION FOR SELECTING BETTER MATERIAL PROPERTIES FOR ON-FIELD SCENARIO.…
21 Jan 2024 07:08 PM IST
Assignment 3-2D Element Formulation Challenge
OBJECTIVE RUN THE BASE SIMULATION (ASSIGNMENT 2 FILES) AND COMPARE THE RESULTS OBTAINED WITH SAME FILE AFTER MODIFICATION AS SPECIFIED BELOW. run time = 55 ms. animation steps max @60 and min @25. Ishell = 24 Ismstr = 2 Ish3n = 2 N = 5 Ithick = 1 Iplas = 1 COMPARE THE MASS AND ENERGY ERROR, VARIATION…
18 Jan 2024 07:39 PM IST
Assignment 2-RADIOSS Engine File Editing & 3D Meshing Challenge
OBJECTIVE: TO CHECK THE MATERIAL PROPERTIES OF THE GIVEN RAIL COMPONENT AND TO CALCULATE THE SPEED OF SOUND THROUGH THE SAME. TO CALCULATE THE TIME TAKEN FOR A SHOCK WAVE TO TRAVEL FROM ONE END OF THE RAIL TO THE OTHER WHERE LENGTH OF THE RAIL IS ABOUT 1000 MM. SIMILARLY TO FIGURE OUT THE TIME FOR SOUND…
16 Jan 2024 08:47 PM IST
Assignment 1-2D Meshing Challenge
OBJECTIVE To carry out cleanup operation procedure on the given files without any free edges, converting all of them into refine geometry. PROCEDURE Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Deleted the solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. Fillets…
15 Jul 2023 05:59 PM IST
Week 12-Creation of 1D Connectors Challenge
OBJECTIVE To mesh the geometry considering the given Quality Parameters and to create connectors for attaching various components. PROCEDURE Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. 2D mesh was applied @2D>AUTOMESH>SURFACES>QUADS>ELEMENT SIZE - 5>MESH. Quality…
04 Jul 2023 03:22 PM IST
Week 11-3D Tetra Meshing Challenge
OBJECTIVE To create Tetramesh for the given models following each Quality Criteria. PROCEDURE (MODEL 1) Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Deleted the solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY after getting a 'Topo' view. Remove fillets and minimum…
29 Jun 2023 03:11 PM IST
Project-2-Meshing of Door Inner Panel Challenge
OBJECTIVE To follow the Quality Criteria and mesh the given component and assign thickness. PROCEDURE Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Deleted the solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. Fillets present at the feature areas were removed using…
20 Jun 2023 03:44 PM IST
Week_8_Plastic Model_1
OBJECTIVE To mesh the Plastic Model with given quality parameters without using auto-midsurfacing option. PROCEDURE Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Delete solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. For each feature area, mesh was deployed…
03 Jun 2023 06:22 PM IST
Project 1-Meshing of Rear Wheel Holder challenge
OBJECTIVE To mesh the given component of a car with given quality parameters and to assign thickness. PROCEDURE Geometry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Delete solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. Midsurface was extracted using @GEOMETRY>MIDSURFACE>AUTO-EXTRACTION>SURF.>ALL>EXTRACT>OK.…
28 May 2023 09:25 AM IST
Week 7- Meshing of Backdoor Challenge
OBJECTIVE To mesh the backdoor geometry of a car with given quality parameters. that you have to follow. PROCEDURE Geommetry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Delete solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. Only half of the model is used initially…
23 May 2023 06:56 PM IST
Week 6-Meshing of Hood Challenge
OBJECTIVE To mesh the given components below and assign the thickness provided, also to verifiy the given quality criteria upon the model. PROCEDURE Geommetry was imported @IMPORT>FILES>IMPORT>GEOMETRY>ALL>IMPORT. Delete solids @DELETE>SOLIDS>SOLIDS>ALL/DISPLAYED>OK>DELETE ENTITY. Midsurface…
15 May 2023 07:04 PM IST
Week 4-1D Element Creation Challenge
Objective Generating mesh, deploying 1D element and defining the cross-section for the same with property assigning. Procedure Geometry was imported to CAD using @FILE>IMPORT>GEOMETRY>IMPORT and switched to ‘Shaded Geometry and Surface Edges’. Now for mid-surfacing @GEOMETRY>MIDSURFACE>(SURFS,…
04 May 2023 06:11 PM IST
Week 9 - Creating connection for Rear door
Objective THE MAIN OBJECTIVE IS TO DEPLOY DIFFERENT PID'S FOR THE COMPONENTS AND TO ESTABLISH SUITABLE CONNECTIONS. Procedures GIVEN CAD MODEL WAS EXPORTED TO ANSA AND PID WAS CREATED FOR EACH PART USING @MESH>MACROS>SET PID. DOOR HINGE WAS FIRST CONNECTED TO THE DOOR BODY USING BOLTS @TOPO>POINTS>ON COG AND…
22 Apr 2023 06:43 PM IST
Week- 8 - Solid meshing
Objective Main Objective is to check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias. To use tetra elements to mesh the Volumes defined in the model and check for the quality after Volume meshing. Procedures CAD model was exported to ANSA and the geometric errors were checked…
16 Apr 2023 08:06 AM IST
Project 2 - 2D meshing on the instrumental Panel
Objective Main objective in this challenge is to take the midsurface and mesh the same after checking and eleminating all geometric errors. Meshing are to be done using different meshing techniques as instructed with proper thickness assignment. Procedures CAD model was exported to ANSA and the geometric errors were checked…
12 Apr 2023 07:34 PM IST
Week - 5 - 2D meshing for Plastic components
Objective Main objective is to take the midsurface of all the components after eleminating the geometric errors and to further proceeding with meshing upon the midsurface within the given quality criteria. Procedures CAD model was exported to ANSA and the geometric errors were checked and rectified. Used @MENUBAR>TOOLS>CHECKS>GEOMETRY…
06 Apr 2023 06:42 PM IST
Project 1 - Meshing of Floor Panel
Objective Main objective is to take the midsurface of all the components after elemenating the geometric errors and to further proceeding with meshing the midsurface within the given quality criteria. Procedures CAD model was exported to ANSA and the geometric errors were checked and rectified. Used @MENUBAR>TOOLS>CHECKS>GEOMETRY…
30 Mar 2023 05:51 PM IST
Week 4 - 2D Meshing for Sheet Metal
Objective Main objective is to take the midsurface of all the components after elemenating the geometric errors and to further proceeding with meshing the midsurface within the given quality criteria. Procedures CAD model was exported to ANSA and the geometric errors were checked and rectified. Used @MENUBAR>TOOLS>CHECKS>GEOMETRY…
24 Mar 2023 06:17 PM IST
Week 3 - 2D meshing for Sheet metal
Objective Main objective is to take the midsurface of all the components after eleminating the geometric errors and to further proceeding with meshing the midsurface within the given quality criteria. 2. Procedures CAD model was exported to ANSA and the geometric errors were checked and rectified. Used @MENUBAR>TOOLS>CHECKS>GEOMETRY…
19 Mar 2023 05:52 PM IST