Sumedh Laghate
bolt it up let it happen
Skills Acquired at Skill-Lync :
Introduction
13 Projects
Week- 5 - Solid meshing
AIM: For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criteria given maximum length 2mm average length 1 mm minimum length 0.5 mm. Use tetra elements to mesh the Volumes defined in the model and check for the below quality after Volume…
27 Jun 2022 04:23 PM IST
Week 3 - 2D meshing for sheet metal
AIM:For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria objective: to get model fe of the sheet metal component using mid suraceing operations procedure: 1) Import the geomery in ansa , set cons…
30 Jun 2022 04:05 PM IST
Week - 4 - 2D meshing for Plastic components
)AIM: For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with given element Quality criteria. objective: To extract manual mid-surface for the plastic…
05 Jul 2022 08:49 AM IST
Week 6 - Creating connection for Rear door
aim: to do connections in rear door handle =. procedure: 1) open the model in ansa. 2) create the property id for various components of door. 3) go to nastran deck select rbe 2 , apply rbe 2 to all the parts where bolts are needed, like hinge, hinge mounts , brackects . 4) for the hinge allow the rotation in z axis. and…
19 Sep 2022 01:27 PM IST
Tool Test 1
tool test are attached
26 Sep 2022 10:20 AM IST
Tool Test-2
tool test is attached
28 Sep 2022 02:06 PM IST
Project - 2 - Meshing on the suspension Assembly
AIM:For the given assembly, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned for mid surfaces. Use tetra elements to model non-uniform thickness components. Also, use Appropriate connections to connect the component.Use PBAR…
11 Oct 2022 07:22 AM IST
Project 1 - 2D meshing on the instrumental Panel
AIM:For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. precedure : import the geometry in the ansa. set cons resolution to 1. using faces new option close the geometry. after closing…
13 Oct 2022 04:39 AM IST
Week 4-1D Element Creation Challenge
Aim: Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF. procedure: import the model. obtain the midsurface using automid in surface option on mid surface create a washer element generate mesh using 5mm grid size for generating…
19 Oct 2022 08:58 AM IST
Week 6-Meshing of Hood Challenge
AIM: Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle…
15 Nov 2022 04:54 PM IST
Week 8-3D Tetra Meshing Challenge
AIM: Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units Tet collapse: 0.15 Housing Model For the given model, Create a 3D Tetramesh with the following quality criteria. TetraMesh Generation…
24 Nov 2022 03:27 PM IST
Week 9-Creation of 1D Connectors Challenge
AIM: For this challenge, you will have to mesh the given geometry. Provided below are the quality parameters that you have to follow. Target Element size - 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max.…
30 Nov 2022 06:54 AM IST
Week 12:Project 2-Meshing of Rear Wheel Holder challenge
aim : Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad…
03 Dec 2022 05:15 PM IST
2 Course Certificates
HyperMesh for FEA Plastic and Sheet Metal Applications
Academic Qualification
B.E
Government College
31 May 2016 - 31 May 2021
12th
Kendriya Vidyalaya VSN Nagpur
01 Apr 2014 - 25 May 2015
10th
Kendriya Vidyalaya VSN Nagpur
01 Apr 2012 - 31 Mar 2013
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner