Aim:To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component. Objectives:  Creation of Tooling Axis. Creation of Class B and Class C surface. Creating a solid part out of surface modelling. Draft Analysis of Class A surface and final plastic…

Aim: This project aims to create a switch bezel plastic component using the given class A surface following the OEM standard. and perform the draft analysis. Class A-surface Objective: Ensure Proper Tree Structure. Geometrical sets should have a proper name based on the sketches present inside them. All the sketches…

SHORT REPORT:- FIRST OF ALL I CREATE ALL PARTS SAPPARATELY AND THEN FOR OPEN THE PART IN ASSEMBLY DESIGN I CREATE A PRODUCT FILE AND USE EXISTING COMPONENT COMMAND AND SELECT THE PARTFILE.AFTER ALL PARTS ARE OPEN IN PRODUCT FILE AND THEN  I ASSEMBLED THESE  PARTS IN ASSEMBLY DESIGN WITH THE HELPS OF REFERANCE…

DRAFT ANALYSIS REPORT:-ALL CLASS A SURFACE HAVE DRAFT ANGLE UP TO THREE DEG. ALL CLASS B SURFACE HAVE DRAFT ANGLE UPTO 3DEG. ALL CLASS C SURFACE HAVE ANGLE UP TO 2.9 DEG. ALL RIBS WALL HAVING DRAFT ANGLE UPTO 0.5 DEG. DRAFT ANALYSIS ON LIFTER AXIS:-IN DOG HOUSE BLUE COLORED WALL HAVE 0.5DEG. DRAFT ANGLE AND GREEN COLORED…

*REPORT ON DRAFT ANALYSIS OF THE ARM REST- THE CLASS A SURFACE HAVE SOME AREA WITH NEGTIVE DRAFT ANGLE WITH MAX VALUE -24DEG IN CLASS B HAVE SAME AREA WITH NEG DRAFT ANGLE ALL CLASS C HAVE DRAFT ANGLE UPTO 2.9DEG ALL B SIDE FEATURES HAVE DRAFT ANGLE UP TO 0.5DEG. *REPORT OF DRAFT ANALYSIS ON LOWER SUBSTRATE:- ALL CLASS…

COMPARISON:- AFTER COMPARISON BETWEEN THESE VEHICLE I SUGGEST TO MARUTI SUZUKI BREZZA BECAUSE OF GOOD MILEAGE WITH HEAVY POWER AND TORQUE. THE SECOND FACTOR IS BREZZA HAVE GOOD GLOBAL SAFETY STAR RATING 4. BREZZA  HAVE LOW MAINTENANCE COST FROM THE OTHER 3 CARS. AND THE MAIN RESION IS BREZZA IS A BIG CAR. *BENCH MARKING:-BENCH…

UNDERBODY COATING:-Underbody coating providing long term protection from corrosion to cars underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible but are prone to corrosion.Applying a layer of undercoating creates a barrier against the sound,…

Aim : To Design outer panel, inner panel and necessary reinforcements Theory :                 The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment,…

Aim: To find the section modulus of the hood and optimization to improve the overall section modulus.   Objective: Use the section from your Hood design and calculate the section modulus using the formula S= I/y.   Section Modulus: The section modulus (S) is geometry property of the cross section used for designing beams…

AIM: To create a report on fender regulation and to calculation the wheel arc area and prove whether the car will pass the standards or not by using the European standards. Fender: A fender is the part of a car, truck, motorcycle, or other vehicles that frames or covers a wheel well. Its main purpose is to prevent debris,…

FENDER DESIGN OBJECTIVE : The main objective of this project is to design a fender using  a new age design software - NX - CAD INTRODUCTION : Design of any product starts from an requirement . The design engineer sketches the product based on the the requirement . Then the 2D sketch  with the proper dimensions…

Aim: Design a Car Roof with its components by following the master section of the front roof rail (Front roof rail, bow roofs, center roof rail and rear roof rail) with all the design parameter. Abstract: Safety point of view vehicle roof plays very crucial role specially roll over kind of accidents, in which vehicle…

AIM: To Design the outer upper and lower panel, inner panel with the necessary reinforcements by following the Master section with the design parameter for the given class A surface. INTRODUCTION: The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often…

                                      WIRING HARNESS DESIGN IN CATIA V5 INTRODUCTION: Wiring harness is the combination of electrical and mechanical CAD to connect all the electrical parts in the automotive at the optimum level.…

Aim: To download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Introduction: Clips: This is the important component of the wiring harness which would be defined before wiring harness routing. Clips accumulate the bundle in…

Wiring harness design in CATIA V5 - 3D modeling   Aim To Route the following harness layout in the Electrical workbench. Add protective covering on all branches   Software Used Catia V5   Introduction CATIA® is the world's engineering and design leading software for product 3D CAD design excellence.It…

Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness A and Harness B as per the…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…

Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given Bugatti V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry…

Aim: To route the wiring harness on the given tailgate assembly and prepare the flatten view drawing in CATIA V5.  Given: Car Tailgate Assembly                                              …