…

                                                                                           …

                                                                                            H00D DESIGN Introduction of hood A car hood also referred to as a bonnet in some other countries is the hinged cover that rests over the engine of a front-engine vehicle. Its purpose is to provide access to the engine for repair…

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                                                                   ROOF DESIGN For the given roof styling, develop the essesntial flanges and reinforcements, provide appropriate dimensions and check for draft analysis and to perform roof curvature study using…

          Car Back Door Design   Aim: To design car back door from given styling surface data under given design rules and regulations.   Car Back Door and Components:                The back door is a hinged door/tailgate at the rear of the vehicle. It may be used for loading and unloading cargo, or to get passengers…

                                                                                           …

  DESIGN OF CLASS A, CLASS B AND CLASS C SURFACE OF SWITCH BEZEL USING CATIA V5 Aim The aim of this project is to develop the product design of the switch bezel with the help of the class A surface following the OEM standards. Introduction Class A Class A surface is the term mainly used in automotive design industry. It…

  TO DESIGN A COIN HOLDER BY USING CLASS A SURFACE  AIM:  To design a coin holder Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis  …

Challenge 6 - Core & Cavity Design AIM : To create the Core and cavity blocks for the Switch Bezel Component.   OBJECTIVE : To Create Core, Cavity and Parting surface for the given component along the Tooling Axis.   CORE : Core is a preformed, bonded, sand insert placed into the mold to shape the interior…

   DOOR HANDLE Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected. By analysing the component the most easily ejectable direction is somewhere close to the Z…

   Objective: The main objective of this challenge is to create a solid body of 'Bumper' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Bumper. Overview:Initially, we need to offset the…

  Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and join them.…

DOOR TRIM LOWER AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surfaceand the outermost surface.CLASS-B SURFACE: a surface below a certain thickness from the…

DOOR TRIM LOWER WITH ENGINEERING FEATURES (HEAT STAKES AND LOCATORS) The aim of the project is to design a solid body from the given class A surfaces by creating tooling axis, B and C surface  then do the draft analysis for the same then conclude the result by adding engineering features like heat stakes and the locators.…

  Objective: The main objective of this challenge is to understand the given master section to create a solid body and B-side features for a given class A surface, by considering all the design parameters. Master Section: Master sections are the guides for design requirements which decide the component…

                                                                                           …

AIM: To design the car door inner panel with reference to given Class-A surface by using given mastersection, creating attachment features and performing draft analysis to check the manufacturing feasibility of the component by using software CATIA V5. Objective: The project deals with the explanation of method followed…

Title: Defining Connectors and Clips using CATIA V5 Objective : Downloading the 3D CAD files form the te.com website and then defining the parts electrically and further creating a catalogue for the components. Introduction:  A connector is a device(or more precisely, a mating pair of devices, often a plug…

AIM:   To solve the above assignment questions and define the necessary electrical properties in the respective workbench.   OBJECTIVE:   To download the P-Clamp CAD data and define it as Electrical Support in the Electrical Part design workbench and also define the necessary electrical properties. To download…