FREQUENCY ANALYSIS : To perform a frequency analysis on a rotating shaft Created a model rotating shaft in SolidWorks with considered dimensions. Selected a new study in SolidWorks Simulation after creating a model. Applied frequency analysis to perform simulation Applied an Alloy steel material to the model Material Properties…

Objective : To design surface models of different parts of sunseeker predator yacht using Solidworks 2018 To assemble different parts of the model yacht. Parts to be modeled for yacht, Propeller Radar Blueprint Hull Garage door Front seat Middle seat Rear seat Superstructure Radar mast 1. Propeller A propeller is a rotating…

Comparison of Bending in beams Aim: Compare the performance of three types of beams under a bending load with a load of 1500N and compare the results of stress, displacement, and strain These three types of beams are modeled in Solidworks and the analysis performed using Solidworks simulation Case - 1: Rectangular Beam…

American Chopper - Week 6 Program (Gasfuel_tank & Assembly)   Google drive link for Gas tank https://drive.google.com/open?id=1uX71fjHoFbekUQ0Vp8rH7ix1uHbwikT2 Google drive link for American_chopper_Assembly & All Part models https://drive.google.com/open?id=1NkXf8j56Pm8hni56vBXixawxbUovDiA4  

American chopper- Week 4 Program(Rear wheel and Front fork) https://drive.google.com/open?id=1ebvgI1j7RTFT0jKEBsxpnfqlCeYNV-eH Rear wheel - It took me 6hrs to design First, I have choosen the front plane to sketch the Profile of the rim and hub and i made that skectch into solid part by using revolve command based on the…

Objective : To design a model of different parts of American chopper using Solidworks 2018. To assemble these parts modeled for the chopper. And to create a photorealistic model of the chopper and render the model using Solidworks photoview360. Following parts modeled for the chopper, Transmission belt Kickstand Front…

Analysis on a plate with a hole   Case - 1 : Created a model in Solidworks to perform a static analysis on a plate with a circular hole at a center. Dimensions for that model Length = 300mm Height = 120mm Thickness = 30mm A circular hole at a center with a diameter of 60mm     Click new study option to perform…

Front wheel_American chopper https://drive.google.com/open?id=11H1Mw97RQ0a4FgIZ2Kn6geJxv1QXpfF0 It took 7hrs for me to design. First, I sketched the profile of the rim as well as hub after that i made a solid part using revolve command. next, I sketched inner design of the rim and extruded it after that i used circular…

Google drive link for the second week challenges https://drive.google.com/open?id=1PDavb4CZ8urajbmu0aOtbJSW4Q_IXlIh Oil tank - I learned these commads - Sketching - Dimensioning - Extrude - Combine - Fillet - Creating a inner shell - Appearences Chain - I learned these commands - Sketching - Dimensiong - Straight…

Buckling Analysis on a cyclonic separator stand   Buckling Analysis: When the lengthy beam is subjected to compressive axial stress, it tends to deflect sideways. (When the structure is subjected to compressive stress, buckling may occur)   For the Cyclonic separator stand : The cyclonic separator stand is modeled…

Google Drive link for the first week challenges https://drive.google.com/open?id=1xmFoJuXZa7N5vNiFtppkbMY_KxSpXj9F Transmission belt - I learned these commands - Sketching - Dimensioning - Extruding - Fillet - Offset entities - Appearances Kick Stand - I learned these commands - Sketching - Dimensioning - Creating planes…

American Chopper - Week 5 Program (Chassis & Engine) Drive Link https://drive.google.com/open?id=1gJvuCVms8MZBFm3iAeJLmSu_YRk9vCM8  

Project - Part Modeling using Boolean Operations Using Positioned Sketch for all the sketches in this part modeling. All Sketches are fully constrained, and the part model along with the tree structure illustrated below. Tree Structure: Sketches: Circular base Screwface for Circular base  Rectangular base Screwface…

DRAFTING WORKBENCH: CAD MODEL: DRAFTING (2D Drawing):

SURFACE CREATION AND DRAFT ANALYSIS FOR DOOR SWITCH BEZEL: Aim: To create a surface model of door switch bezel and add a thickness of 2.5mm to it, and also perform draft analysis to the model.   As a plastic product designer, there are some objectives to consider for designing, Inspect the Class – A –…

SURFACE CREATION AND DRAFT ANALYSIS FOR DOOR ARMREST: Aim: To create a surface model of door armrest and add a thickness of 2.5mm to it, and also perform draft analysis to the model.   As a plastic product designer, there are some objectives to consider for designing, Inspect the Class – A – Surface Create…

  DESIGNING OF LOCATORS AND HEAT STAKES FOR DOOR APPLIQUE:   Aim: To Design the Attachment features of Locators and Heat Stakes by following design guidelines for Door Applique   Heat Stakes: It is also called Plastic Welding. In manufacturing products with thermoplastic components, it is often necessary…

  Development of 3D model by following the master section of Pillar cover   Master Section: During the period of the vehicle concept design, the evaluation of master section performance mostly depends on reference vehicle data and the experience of structural design engineers. Master sections working in the stage…

   DEVELOPMENT OF A DOOR TRIM PANEL:   Aim: Creation of CAD model considering following inputs as like in OEM industries. a) Class – A – Surface b) Nominal thickness from the master sections reference c) Attachment features for the door panel, Heat Stakes for a part to part attachment Pushpin…

  UNDERBODY COATING:   Cars underbody is more prone to corrosion. Underbody coating provides long term protection from corrosion to cars underbody. It also protects parts like the internal body parts, frame rails, and other inner cavities that are not physically accessible but are prone to corrosion.   Main…