GATE Electronics (EC): Electronic Devices (energy bands, carrier concentration, drift and diffusion, P-N junction, BJT, MOS capacitor, MOSFET, LED and solar cell), previous-year questions solved, part 3

Part 3 of 3 of the Electronic Devices: MOSFET, PN Junction hub: 8 more official GATE EC questions on MOS capacitor and MOSFET, each solved step by step and checked against the official answer key. Part 1 covers energy bands, carrier concentration and Fermi level, carrier transport: drift, diffusion, generation and recombination and p-N junction, Zener, BJT and optoelectronic devices.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 8 of 30 questions on this page

GATE 2022 · EC · Q.18MCQ · 1 markMOS capacitor and MOSFET

pMOS (W/L = 5) and nMOS (W/L = 1), gates tied to output, 4 V supply: is V_o equal to, above or below 2 V?

Consider the CMOS circuit shown in the figure (substrates are connected to their respective sources). The gate width () to gate length () ratios of the transistors are as shown. Both the transistors have the same gate oxide capacitance per unit area. For the MOSFET, the threshold voltage is and the mobility of holes is . For the MOSFET, the threshold voltage is and the mobility of electrons is . The steady state output voltage is ________.
A pMOSFET (W/L = 5) on top and an nMOSFET (W/L = 1) below, in series between a 4 V supply and ground. The two gates are joined to each other and to the drain node, which is the output V_o. The pMOS source is at the 4 V terminal and the nMOS source is grounded4 VVOW/L = 5W/L = 1pMOSFETnMOSFET
  1. (A)equal to
  2. (B)more than
  3. (C)less than
  4. (D)equal to

Answer: (C) Official key: C

  1. Each gate is tied to its own drain (the output node), so in both devices and each one is in saturation: is always true for .
  2. Steady state: the same current flows through both. With (the same cancels): and in the same units.
  3. , so .
  4. , which is less than 2 V: option (C).
  5. Check: of the pMOS and of the nMOS , both above 1 V, so both are on and saturated.

Trap: assuming a symmetric divider gives exactly 2 V, option (D). That is true only if . Here the nMOS is stronger (its is 300 against 200), so it pulls the node lower than the middle. Forgetting the mobilities (using only of 1 and 5) gives 2.38 V, option (B). We solved the current balance by bisection with full triode and saturation logic and got 1.899 V.

Where this shows up in industry

A diode-connected MOSFET, gate tied to drain, is the basic reference element of a current mirror and the load in many biasing cells. Its voltage follows the square-law equation, so SPICE model parameters for threshold voltage and mobility set the bias point directly.

GATE 2022 · EC · Q.20MCQ · 1 markMOS capacitor and MOSFET

nMOS and pMOS pass transistors (Vt = 1 V and -1 V) charging 1 uF capacitors: steady-state V1 and V2?

The ideal long channel MOSFET and MOSFET devices shown in the circuits have threshold voltages of and , respectively. The MOSFET substrates are connected to their respective sources. Ignore leakage currents and assume that the capacitors are initially discharged. For the applied voltages as shown, the steady state voltages are _________________.
Two MOSFETs used as pass transistors, each charging a 1 microfarad capacitor to ground. Left: an nMOSFET with gate at 5 V and the 5 V source on its left terminal, capacitor node V1 on the right. Right: a pMOSFET with gate at minus 5 V, 5 V on its left terminal and capacitor node V2 on the right5 V5 VV11 μFnMOSFET−5 V5 VV21 μFpMOSFET
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. nMOS: the capacitor node is the source (the lower potential terminal). The channel stays on only while . Charging stops when , so . An nMOS passes a weak 1: it loses one threshold.
  2. pMOS: the 5 V terminal is the source (the higher potential terminal) and the capacitor node is the drain. and this never drops, because the source is held at 5 V. The channel stays on until , so . A pMOS passes a strong 1.
  3. So and : option (C).

Trap: assuming both devices pass the full 5 V (option A), or swapping the roles (option B). We simulated both capacitors charging with the square-law model: stopped at 4.000 V and reached 5.000 V.

Where this shows up in industry

This threshold drop is why a single nMOS pass transistor degrades a logic high, and why transmission gates in standard cells and multiplexers use an nMOS and pMOS in parallel. SRAM bit-cell designers also work around it, because an nMOS access transistor cannot pull a node above V_DD minus V_T.

GATE 2022 · EC · Q.34NAT · 1 markMOS capacitor and MOSFET

Ideal p-type MOS capacitor: Q_IN = 2.2 uC/cm^2 at V_G = 2 V, C_OX = 1.7 uF/cm^2: Q_IN at V_G = 4 V?

An ideal MOS capacitor (-type semiconductor) is shown in the figure. The MOS capacitor is under strong inversion with . The corresponding inversion charge density () is . Assume oxide capacitance per unit area as . For , the value of is ______ (rounded off to one decimal place).
An ideal MOS capacitor on a p-type semiconductor: a metal gate on the left with terminal V_G, then the oxide, then the semiconductor whose right end is groundedVGMetalOxideSemiconductor

Answer: Official key: 5.5 to 5.7

  1. In strong inversion the depletion charge has stopped growing, so any extra gate voltage goes into inversion charge across the oxide: .
  2. Use the first point to find the threshold voltage: , so . This is below 2 V, so is indeed strong inversion.
  3. At : .
  4. Same result without : rises by , so .

Trap: scaling in proportion to the gate voltage, . The charge is proportional to , not to . We computed both and checked that only lands in the official range 5.5 to 5.7.

Where this shows up in industry

Inversion charge C_ox times (V_GS minus V_T) is the starting point of every MOSFET current model, and a capacitance-voltage sweep of a MOS capacitor is how a fab extracts oxide capacitance and threshold voltage on test structures.

GATE 2022 · EC · Q.40MCQ · 2 marksMOS capacitor and MOSFET

Long-channel nMOS, 100 um by 10 um, mu_n C_OX = 1 mA/V^2, Vt = 1 V, VGS = 2 - sin 2t, VDS = 1 V: peak I_D?

Consider an ideal long channel MOSFET (enhancement-mode) with gate length and width . The product of electron mobility () and oxide capacitance per unit area () is . The threshold voltage of the transistor is . For a gate-to-source voltage and drain-to-source voltage (substrate connected to the source), the maximum value of the drain-to-source current is ________.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. The current is largest when is largest. peaks at .
  2. Overdrive . This is more than , so the device is in the triode region, not saturation.
  3. Triode: with .
  4. : option (C).

Trap: using the saturation formula , option (B), without checking against the overdrive. Forgetting the gives 40 mA, option (A). Taking (so ) gives 5 mA, option (D). We scanned a full period of with region logic: the maximum was 15 mA, in the triode region.

Where this shows up in industry

Checking the region before choosing the current equation is routine in device modelling. A transistor used as a switch or resistor with a small drain voltage sits in the triode region, which is why on-resistance, set by the overdrive voltage, is the figure quoted on power-MOSFET datasheets.

GATE 2023 · EC · Q.19MCQ · 1 markMOS capacitor and MOSFET

MOS capacitor: which plot shows depletion width W_dep against gate voltage V_g (V_fb, V_t marked)?

For a MOS capacitor, and are the flat-band voltage and the threshold voltage, respectively. The variation of the depletion width () for varying gate voltage () is best represented by
  1. (A)Plot of depletion width W_dep against gate voltage V_g with regions accumulation, depletion and inversion marked. W_dep rises steeply from V_fb and levels off at the y-axis, before V_t, then stays flatwdepvfbvtvgaccumulationdepletioninversion
  2. (B)Plot of depletion width W_dep against gate voltage V_g with regions accumulation, depletion and inversion marked. W_dep rises from zero at V_fb with a gradually flattening curve, reaches its maximum near V_t and stays constant in inversionwdepvfbvtvgaccumulationdepletioninversion
  3. (C)Plot of depletion width W_dep against gate voltage V_g with regions accumulation, depletion and inversion marked. W_dep a constant maximum at low gate voltage that falls to zero at V_twdepvfbvtvgaccumulationdepletioninversion
  4. (D)Plot of depletion width W_dep against gate voltage V_g with regions accumulation, depletion and inversion marked. W_dep rises from zero at V_fb to a peak at the y-axis and then falls back to zero at V_twdepvfbvtvgaccumulationdepletioninversion

Answer: (B) Official key: B

  1. Below the semiconductor surface is in accumulation: majority carriers pile up and there is no depletion region, so .
  2. Between and the surface is depleted. A larger gate voltage uncovers more ionised acceptors, so grows. It follows , so rises steadily from zero and the curve flattens as it climbs, like a square root.
  3. At strong inversion starts. The inversion layer now supplies the extra charge, so stops growing and stays at its maximum .
  4. That is plot (B): zero up to , a rise that flattens, a constant level from onward.

Trap: plot (A) levels off well before , with a vertical start. (C) and (D) fall again, as if depletion shrank with more positive gate voltage. We computed for a p-type substrate with a 10 nm oxide: it was zero at , increasing and flattening, and reached exactly at . At 60% of the way from to it was at 73% of , so it had not yet saturated. We then read the sampled curve of each plot: only (B) passes all four checks.

Where this shows up in industry

The maximum depletion width sets the ultimate depth of the channel depletion layer, which is why substrate doping is chosen to trade threshold voltage against short-channel control. Capacitance-voltage measurements on test structures read this width back as the dip and flat floor of the C-V curve.

GATE 2024 · EC · Q.61NAT · 2 marksMOS capacitor and MOSFET

MOS capacitor on p-type silicon, 100 nm oxide, VFB = 0 V: find the silicon work function

Consider a MOS capacitor made with p-type silicon. It has an oxide thickness of 100 nm, a fixed positive oxide charge of at the oxide-silicon interface, and a metal work function of 4.6 eV. Assume that the relative permittivity of the oxide is 4 and the absolute permittivity of free space is . If the flatband voltage is 0 V, the work function of the p-type silicon (in eV, rounded off to two decimal places) is ______.

Answer: Official key: 4.10 to 4.50

  1. Oxide capacitance per area: .
  2. Flat-band voltage: , with .
  3. Oxide-charge term: .
  4. gives , so .
  5. .

Trap: the sign of the charge term. A positive fixed oxide charge shifts negative, so must be positive to bring it back to 0 V. Adding the term instead gives 4.88 eV, outside the official range. The code recomputed , and and confirmed the wrong-sign value falls outside the key.

Where this shows up in industry

Flat-band voltage is measured on capacitor test structures at fab to monitor oxide charge and gate work function, and it feeds the threshold voltage in the SPICE model. High-k metal-gate processes tune the metal work function precisely for this reason.

GATE 2024 · EC · Q.64NAT · 2 marksMOS capacitor and MOSFET

NMOS in linear region gives 5 uA at VDS = 0.1 V: transconductance after VDS goes to 1.5 V

An NMOS transistor operating in the linear region has of 5 µA at of 0.1 V. Keeping constant, the is increased to 1.5 V. Given that , the transconductance at the new operating point (in µA/V, rounded off to two decimal places) is ______.

Answer: Official key: 52.40 to 52.60

  1. In the linear region with .
  2. At : , so .
  3. Now . The device is no longer in the linear region. It is in saturation.
  4. In saturation and .
  5. .

Trap: using the triode formula because the question starts in the linear region. The new exceeds , so the device has moved to saturation. The code compared with and confirmed the saturation value lies inside the key and the triode value does not.

Where this shows up in industry

Compact models such as BSIM switch between the triode and saturation expressions at and keep the current and its derivatives continuous across it. A wrong region in a hand model gives the wrong , which is why transistor sizing for a given gain starts by checking against .

GATE 2026 · EC · Q.60NAT · 2 marksMOS capacitor and MOSFET

n-channel MOSFET with gate tied to drain and a 1 kOhm load, VTH = 1 V: find the gate voltage VG

An n-channel MOSFET is connected as shown in the Figure.
Assume , , and and neglect channel length modulation effects.
The gate voltage () of the n-channel MOSFET (in Volt) is __.
(rounded off to two decimal places)
An n-channel MOSFET with its gate connected to its drain and its source grounded. The drain node, labelled V G, is joined to the supply +V DD through a 1 kilo-ohm resistor+VDD1 kΩVG

Answer: Official key: 2.50 to 2.60

  1. The gate is tied to the drain, so . Then always holds, and the device is in saturation.
  2. Saturation square law: .
  3. The same current flows through the 1 kΩ resistor: .
  4. Equate, with in mA and in volts: , so .
  5. , and , so the device is indeed on. (The other root, , is below threshold.) .

Trap: using and forgetting the factor of the square law. That gives , outside the key range. We solved the node equation both by bisection and by the quadratic formula and got the same .

Where this shows up in industry

A diode-connected MOSFET is the basic building block of a current mirror and of bias generators in analog and mixed-signal chips, and its for a given current is how threshold voltage and are extracted from measurements in SPICE model fitting.

From GATE prep to a core electronics or embedded career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.