GATE Electronics (EC): Calculus, Vector Calculus and Differential Equations (Engineering Mathematics), previous-year questions solved

Every calculus, vector calculus and differential equation question from the last five GATE Electronics and Communication papers, 21 in all: which series converge, maxima and minima on an interval, double integrals over shaded regions, directional derivatives, line and flux integrals, the divergence theorem, and ordinary and partial differential equations. Each answer matches the official key and was recomputed by code: grid and Monte Carlo sums for the integrals, parametrised paths for line integrals, partial sums for series, and substitution plus RK4 for the differential equations.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 18 Nov 2026 · 10 of 21 questions on this page

GATE 2022 · EC · Q.45MSQ · 2 marksSeries and convergence

Series sum of n^d / c^n from n = 1: for which of the given (c, d) does it converge?

Consider the following series:

For which of the following combinations of values does this series converge?
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) and (D) Official key: B,D

  1. Write the term as . Three cases decide everything.
  2. : geometric decay beats any power of . The ratio of consecutive terms tends to , so the series converges for every . (B), , : converges (to ). Converges.
  3. : the series is , a -series with , which converges only for , that is . (A), : the harmonic series, diverges. (D), : converges. (D) converges.
  4. : the factor grows geometrically, so the terms themselves grow. (C), , : the term is , which is at . Diverges.
  5. So the series converges for (B) and (D).

Trap: ticking (A) because . Terms going to zero is necessary, not sufficient: the harmonic partial sum is at and at , still growing like . Ticking (C) because looks tiny is the other slip: the factor wins. The code ran sympy's convergence test on all four series and checked partial sums out to terms; only (B) and (D) have a vanishing tail.

Where this shows up in industry

The series is the z-transform of the ramp-like sequence , and it converges only for , which fixes the region of convergence. An impulse response whose terms decay geometrically is absolutely summable, which is the condition for a stable filter.

GATE 2025 · EC · Q.12MCQ · 1 markSeries and convergence

Which of the series 1/sqrt(n), 1/(n(n+1)) and 1/n! (n from 1 to infinity) converge?

Consider the following series:
(i)
(ii)
(iii)
Choose the correct option.
  1. (A)Only (ii) converges
  2. (B)Only (ii) and (iii) converge
  3. (C)Only (iii) converges
  4. (D)All three converge

Answer: (B) Official key: B

  1. (i) is a -series with , so it diverges. Its partial sum grows like .
  2. (ii) , so the sum telescopes: . It converges to .
  3. (iii) The ratio of consecutive terms is , so by the ratio test it converges. Its sum is .
  4. Only (ii) and (iii) converge: option (B).

Trap: option (D), all three, comes from the idea that terms tending to is enough. The terms of (i) do tend to , but the partial sums are at , at and at , and keep growing. Option (A) forgets that the factorial series converges. The code checked sympy's convergence test, exact Fraction partial sums for (ii) ( exactly) and (iii) ( after terms, equal to ), and the growth of (i) to terms.

Where this shows up in industry

Factorial terms are why the Taylor series of converges for every , so a few terms are enough to compute an exponential in software or to check a small-signal approximation. Terms like shrink but still sum to infinity, which is the reminder that tests for stability or finite energy need more than a decaying term.

GATE 2026 · EC · Q.36MCQ · 2 marksSeries and convergence

Do S_A = sum of n^2 / 2^n and S_B = 1 + 1/2 + 1/8 + 1/16 + 1/64 + 1/128 + 1/512 + ... converge?

Consider the two series, and , where


Which of the following statements is correct for the two given series?
  1. (A)Both and converge.
  2. (B)Neither nor converges.
  3. (C) converges but does not converge.
  4. (D) converges but does not converge.

Answer: (A) Official key: A

  1. : the ratio of consecutive terms is (it is at ). By the ratio test converges. Its value is .
  2. : the denominators are , that is . The exponents come in pairs and .
  3. Group each pair: . This is a geometric series with ratio , so converges to .
  4. Both converge: option (A).

Trap: concluding that diverges because the numerator grows. The denominator grows far faster, and the terms peak near and then fall. The code summed exactly with Fractions to terms (, against the closed form ), checked the pattern against the seven printed denominators, and summed terms of (, against ).

Where this shows up in industry

Series like are the z-transforms of sequences that appear when a filter has repeated poles, and the ratio test gives the region of convergence . Grouping terms into a geometric series, as for , is the same trick used to sum the impulse response of a periodic or multi-rate system.

GATE 2022 · EC · Q.36MCQ · 2 marksMaxima, minima and bounds

Where does f(x) = 8 ln x - x^2 + 3 attain its minimum over [1, e]?

The function attains its minimum over the interval at ________.
(Here is the natural logarithm of .)
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. A continuous function on a closed interval takes its minimum either at a point where or at an end of the interval. Check all of them.
  2. . For this is zero only at , which lies inside because .
  3. , so is a local maximum, not a minimum. Indeed .
  4. End values: and .
  5. The smallest of , and is . So , option (B).

Trap: option (A), , is where , and a quick reader stops there. It is the maximum on this interval: rises from at to at , then falls to at . The code scanned points of : the smallest value is at and the largest at , and sympy found as the only stationary point with .

Where this shows up in industry

Any design knob with hard limits (a bias current, a gain setting, a filter step size) is tuned the same way: find the stationary point, then compare it with both limits. The best setting often sits at a limit, which is why optimisers carry bound constraints.

GATE 2025 · EC · Q.25MSQ · 1 markMaxima, minima and bounds

f(x) = 2x^3 - 3x^2 - 12x + 1 on the reals: which statements about its extrema are correct?

Consider the function , defined as

Which of the following statements is/are correct?
(Here, is the set of real numbers.)
  1. (A) has no global maximizer
  2. (B) has no global minimizer
  3. (C) is a local minimizer of
  4. (D) is a local maximizer of

Answer: (A) and (B) Official key: A;B

  1. , so the stationary points are and .
  2. . At : , a local maximum with . At : , a local minimum with .
  3. So (C) is wrong ( is a maximiser) and (D) is wrong ( is a minimiser).
  4. The leading term dominates for large : as and as . The values at and are about and . So no value is the largest and none the smallest: (A) and (B) are correct.

Trap: ticking (C) and (D), which is what you get by swapping the sign test of ( is a minimum, a maximum). Another slip is to call the local maximum the global maximum, which is false because keeps rising to the right of . The code solved in sympy, tested the sign of , checked on a neighbourhood scan that is a strict local maximum and a strict local minimum, and evaluated at .

Where this shows up in industry

A cubic is the usual model of a mild amplifier nonlinearity. It has a local maximum and minimum near the origin but no global ones, so a cubic fitted to measured data is only trustworthy inside the range of the data: outside it, the model grows without bound while a real amplifier saturates.

GATE 2025 · EC · Q.51MSQ · 2 marksMaxima, minima and bounds

Non-negative continuous f on [2, 8] with max M and min m: which bounds on the integral of f are guaranteed?

Consider a non-negative function which is continuous and bounded over the interval . Let and denote, respectively, the maximum and the minimum values of over the interval.
Among the combinations of and given below, choose the one(s) for which the inequality

is guaranteed to hold.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. On we have . Integrating over an interval of length gives . These are the tightest bounds this information allows.
  2. Because , both and . So and , and therefore . Option (A) is guaranteed.
  3. (B), (C), (D): take , which has and integral . (B) needs : false. (C) needs : false. (D) needs : false. A single counter-example kills each, so none is guaranteed.
  4. The answer is (A).

Trap: ticking (B) because it uses the correct lower bound . Its upper bound is below the true upper bound , so it fails for a constant function. The words “non-negative” matter for (A): for we have , the integral is , and (A) would need , which is false. The code tested all four options on random continuous non-negative functions on plus , , and (integral by the trapezoid rule on points): (A) held every time, and (B), (C), (D) failed already for (integral ).

Where this shows up in industry

This is the estimate engineers use when only the peak and floor of a measured signal are known: the energy or charge over a window of length lies between times the minimum and times the maximum of the power or current. It gives a quick sanity bound on a battery drain or a pulse energy before any detailed integration.

GATE 2022 · EC · Q.53NAT · 2 marksMultiple integrals and areas

Double integral of 3(x^2 + y^2) over the shaded triangle with vertices (0,0), (4,4), (4,-4)

The value of the integral

where is the shaded triangular region shown in the diagram, is _____ (rounded off to the nearest integer).
Shaded triangle D with vertices (0, 0), (4, 4) and (4, -4) in the x-y plane, bounded by the lines y = x, y = -x and x = 4; dotted guide lines at y = 4 and y = -4xy(4, 4)(4, -4)(0, 4)(0, -4)(0, 0)

Answer: Official key: 512 to 512

  1. Read the region off the figure. It is the triangle with vertices , and . For a given between and , runs from the lower edge to the upper edge .
  2. Inner integral: .
  3. Outer integral: .
  4. The value is .

Trap: integrating only the upper half ( from to ) gives , half the answer, because the shaded region is symmetric about the axis. Using the whole rectangle , instead of the triangle gives . The code evaluated the iterated integral in sympy () and summed the integrand on a midpoint grid masked to ().

Where this shows up in industry

The integral of over a region is the polar moment of inertia of a flat plate, and in communications the same integral divided by the area is the average symbol energy of a constellation whose points fill that region. Engineers use it to compare the power cost of different 2-D signal sets.

GATE 2023 · EC · Q.55NAT · 2 marksMultiple integrals and areas

Double integral of xy over the diamond region R bounded by y = x, y = -x, y = x+2, y = -x+2

The value of the integral over the region R, given in the figure, is _______ (rounded off to the nearest integer).
Shaded diamond R with vertices (0, 0), (1, 1), (0, 2) and (-1, 1), with edges y = -x, y = x, y = -x+2 and y = x+2, split by the y axis21ROxyy = x+2y = -x+2y = -xy = x

Answer: Official key: 0 to 0

  1. Read the region off the figure: the diamond with vertices , , and , bounded by below and above. Its boundary is unchanged if is replaced by : the region is symmetric about the axis.
  2. The integrand is odd in : replacing by turns into .
  3. So the left half of the diamond () contributes exactly the negative of the right half, and the two cancel.
  4. Check by the right half alone: . The left half gives .
  5. Total: .

Trap: doing only the right half, where , gives ; the left half gives because is odd in and is symmetric about the -axis. Integrating by mistake gives , and integrating instead of gives the area . The code evaluated the full iterated integral in sympy (), summed on a midpoint grid masked to the diamond (, area ), and confirmed the right half alone is ( on the grid). The integral of , which does not cancel, is .

Where this shows up in industry

If the signal pairs are spread uniformly over this diamond, then by the same symmetry: and are uncorrelated, yet they are not independent, because the allowed range of depends on . The same odd-integrand argument is why an even signal has no sine terms in its Fourier series.

GATE 2024 · EC · Q.36MCQ · 2 marksMultiple integrals and areas

Surface area of the cap of a sphere of radius R that lies north of the 60 degree N latitude circle

Consider the Earth to be a perfect sphere of radius R. Then the surface area of the region, enclosed by the N latitude circle, that contains the north pole in its interior is _______.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Latitude is measured from the equator. A point at latitude N is away from the north pole. So the region is the cap , where is the angle from the pole.
  2. On a sphere of radius the area element is .
  3. .
  4. With : , about . Option (A).
  5. Check with Archimedes: a cap of height has area , and here , the same value.

Trap: treating as the angle from the pole gives (), and the flat disc of the latitude circle has area (). The other region, south of the circle, has area (), which option (D) imitates. None of those three values matches any option. The code integrated in sympy and also counted random points on the sphere: points with latitude at least gave , and only option (A) is within of it.

Where this shows up in industry

The same cap formula gives the area of the Earth seen by a satellite beam: a cap of half-angle at the Earth's centre covers , and is its solid angle in steradians. Coverage planning for LEO constellations and antenna beamwidth calculations both use it.

GATE 2026 · EC · Q.61NAT · 2 marksMultiple integrals and areas

Double integral of (x^2 + y^2 - 1) over the shaded square with vertices (0,0), (1,1), (2,0), (1,-1)

Consider the square region R in the X-Y plane as shown with the dark shading in the Figure. The value of is ____.
(rounded off to two decimal places)
Shaded square region R in the x-y plane with vertices (0, 0), (1, 1), (2, 0) and (1, -1), with a dotted vertical diagonal at x = 10,012Rxy

Answer: Official key: 0.60 to 0.70

  1. Read the region off the figure: the square with vertices , , and . It is symmetric about the axis and has diagonals of length , so its area is .
  2. Limits: for , runs from to . For , runs from to .
  3. Split the integrand. The area part is .
  4. For on : , and .
  5. On : , and its integral over is . So .
  6. Hence .

Trap: leaving out the gives , and integrating over the upper half only () gives . Both are outside the key range to . The code evaluated the iterated integral in sympy () and on a midpoint grid masked to (, area ). As an independent check, the integral of about the centre is (grid: ), and the parallel-axis shift by the centre distance adds , giving again.

Where this shows up in industry

The average of over a region is the mean power of a point chosen uniformly in it. For this diamond it is about the origin and about its own centre, which is the kind of calculation used to get the average energy of a 2-D constellation or the second moment of an aperture in antenna work.

From GATE prep to a electronics modelling and simulation career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.