GATE Electronics (EC): Electronic Devices (energy bands, carrier concentration, drift and diffusion, P-N junction, BJT, MOS capacitor, MOSFET, LED and solar cell), previous-year questions solved, part 2
Part 2 of 3 of the Electronic Devices: MOSFET, PN Junction hub: 7 more official GATE EC questions on p-N junction, Zener, BJT and optoelectronic devices, each solved step by step and checked against the official answer key. Part 1 covers energy bands, carrier concentration and Fermi level, carrier transport: drift, diffusion, generation and recombination and MOS capacitor and MOSFET.
Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 7 of 30 questions on this page
Which statements about the DC current gain of a BJT are true?
- (A)Under high-level injection condition in forward active mode, will decrease with increase in the magnitude of collector current.
- (B)Under low-level injection condition in forward active mode, where the current at the emitter-base junction is dominated by recombination-generation process, will decrease with increase in the magnitude of collector current.
- (C) will be lower when the BJT is in saturation region compared to when it is in active region.
- (D)A higher value of will lead to a lower value of the collector-to-emitter breakdown voltage.
Answer: (A) and (C) and (D) Official key: A;C;D
- (A) is true. At high injection the injected minority carriers in the base are comparable to the base doping. The collector current then grows more slowly, as , while the base current still grows as . So falls. In a Gummel-Poon model fell at every step as rose.
- (B) is false. At low injection a recombination current in the emitter-base depletion region adds a base current that grows only as . That term dominates at small , so rises with there. In the model went from 0.3 to 5.0 over the range tested.
- (C) is true. In saturation the collector junction is also forward biased, so it injects carriers back into the base and takes away collector current while adding base current. The forced is below the active-region . The Ebers-Moll model gave 86 in saturation against 100 in the active region.
- (D) is true. with between 3 and 6 for silicon. A larger amplifies the leakage of the collector junction, so breakdown starts at a lower .
- Correct options: (A), (C) and (D).
Trap: marking (B) because is said to drop at both ends of the current range. It does drop at high current, but at very low current recombination in the emitter-base junction makes climb. The code evaluated over the low-current and high-current ranges and over saturation and active bias, and against : statements (A), (C), (D) held and (B) did not.
Datasheets and SPICE models show this directly: the beta against collector-current curve rises, peaks and falls, and the model parameters IKF (knee current) and ISE (recombination current) set the two ends. Designers choose the collector current of a transistor near the peak of that curve.
Solar cell with 1 mA photocurrent, maximum power at 0.3 V, thermal voltage 30 mV: find I0
Answer: Official key: 4.00 to 4.26
- Solar cell current: . Power: .
- Maximum power: , that is with .
- .
- .
Trap: treating 0.3 V as the open-circuit voltage, so that . That gives , about 11 times too large. At the maximum power point the cell still delivers current, so the factor is needed. The code scanned for this and confirmed the maximum sits at 0.3 V.
Module makers fit this single-diode model to measured I-V curves to extract , and a lower means a higher open-circuit voltage and fill factor. Maximum-power-point trackers in inverters keep the module at this as light and temperature change.
Ideal germanium diode, I0 = 10 uA at 300 K: forward voltage for 100 mA
Answer: Official key: 0.23 to 0.24
- Ideal diode equation: , so .
- .
- .
- .
- .
Trap: using instead of the natural logarithm, which gives 0.10 V, or reading the 10 µA as 10 mA, which gives 0.06 V. Both fall outside the key. The code substituted the answer back into the diode equation and recovered 100 mA.
A germanium diode turns on near 0.2 to 0.3 V against about 0.6 to 0.7 V for silicon, because germanium's narrower band gap gives a much larger saturation current. That is why germanium diodes were used where a low forward drop mattered, such as small-signal detectors, before Schottky diodes took over.
Which is the dominant transport mechanism for current flow in a Zener diode in breakdown?
Which is the dominant transport mechanism for current flow in this case?
- (A)Drift
- (B)Diffusion
- (C)Tunneling
- (D)Ballistic transport
Answer: (C) Official key: C
- A Zener diode is a heavily doped p-n junction. The depletion region is only tens of nanometres wide, so even a few volts of reverse bias put a field of the order of across it.
- At that field the valence band on the p side lines up with the conduction band on the n side across a very thin barrier. Electrons cross it by band-to-band tunneling, with no collisions needed.
- Drift is how carriers move once they exist, and diffusion needs a concentration gradient. Neither creates the sudden rise of reverse current. Ballistic transport means travel without scattering, which is not the breakdown process.
- The dominant mechanism is tunneling: option (C).
Trap: choosing (A) because a reverse-biased diode current is \"field driven\". The field only sets the barrier. In a lightly doped junction (Sze: breakdown above about , here for ) the same current comes from avalanche multiplication, not tunneling. We computed the one-sided breakdown voltage: for , below (tunneling), with a peak field of .
Reference Zeners below about 5 V work by tunneling and have a negative temperature coefficient, while those above about 6 V work by avalanche and have a positive one. Between about 5 and 6 V the two effects roughly cancel, which is why temperature-stable reference Zeners are made near that voltage.
p-n junction forward biased with 2 V: energy difference between quasi Fermi levels Efn and Efp
Which of the following is/are the correct magnitude(s) of the energy difference between quasi Fermi-levels, in the n-side and in the p-side?
- (A)2 eV
- (B)1 eV
- (C)2 V
- (D)1 V
Answer: (A) Official key: A
- Under forward bias the electron and hole populations are out of equilibrium at the edges of the depletion region. Each carrier type gets its own quasi Fermi level.
- The applied bias appears directly as the separation of the two levels: .
- With , .
- Options (C) and (D) are in volts, which is a potential, not an energy, so they cannot be an energy difference. Option (B) is half the value. Correct option: (A).
Trap: choosing (C) because the number 2 matches the 2 V bias. The numerical value is the same, but the question asks for an energy, so the unit must be eV. We computed and checked each option for both its unit and its number: only (A) passes.
Device simulators such as TCAD plot the two quasi Fermi levels across a diode, LED or solar cell, and their separation at a contact is exactly the applied voltage. In a solar cell, the splitting at the junction under illumination sets the open-circuit voltage.
Two BJT output characteristics at constant IB: which statements about the Early voltages are correct?
Which of the following options is/are correct regarding the Early voltages?
- (A)
- (B) is infinitely large
- (C)
- (D) is finite
Answer: (C) and (D) Official key: C;D
- In the active region, , a straight line with slope . Extend it back to and it crosses the axis at .
- Both curves leave the same knee at the same , so they have the same . The steeper line then has the smaller .
- BJT 1 is steeper than BJT 2, so . (C) is true and (A) is false.
- An infinite Early voltage would mean a perfectly flat line. BJT 2 is the flatter one, and it still rises, so is finite: (D) is true. BJT 1 rises even faster, so is finite too: (B) is false.
- Correct options: (C) and (D).
Trap: reading a steeper curve as a \"better\" transistor with a larger Early voltage. Steeper means more output conductance , so a smaller . We read the plotted lines, extended each back to and got with both finite (about 361 and 750 in figure units).
The Early voltage is a SPICE model parameter (VAF) and sets a transistor's output resistance . Analog designers pick longer-base or lower-doped devices when they want a high intrinsic gain .
LED with 1.3 eV direct bandgap: in which wavelength ranges will it NOT emit?
Given: Plank's constant, and speed of light in free space is .
In which of the following wavelength ranges the LED will NOT emit?
- (A)
- (B)
- (C)
- (D)
Answer: (A) and (B) and (D) Official key: A;B;D
- An LED emits photons of energy close to the bandgap. The matching wavelength is .
- Emission is centred a little above and spread over a few ( at room temperature, about 25 nm here). Photons well below cannot be made, because there are no states in the gap to recombine across.
- (A) 1410 nm and (B) 1090 nm are longer than 956 nm. Their photon energies are 0.88 eV and 1.14 eV, below : no emission.
- (D) 510 nm is a photon of , far above . No carriers sit that high, so there is no emission either.
- (C) 950 nm 20 nm covers 956 nm, so the LED emits there. The ranges with no emission are (A), (B) and (D).
Trap: ruling out only the longer wavelengths, since \"energy below the gap\" is the familiar rule, and keeping (D) as possible because it is above the gap. An LED cannot emit a photon far above its gap, because carriers sit within a few of the band edges. We modelled the direct-gap spectrum : relative intensity is zero in (A) and (B), below in (D) and above 0.1 of the peak in (C).
The peak wavelength of an LED is in micrometres with in eV, which is how GaAs (about 870 nm) and InGaAsP telecom (1310 and 1550 nm) emitters are chosen. A real emitter's linewidth grows with temperature, so datasheets give peak wavelength and spectral half-width together.