Seismic base shear calculator as per IS 1893:2016
Work out the design base shear of a building by the equivalent static method: seismic weight, approximate period, Sa/g, Ah, the minimum base shear and the force at every floor. Free, no sign-up, runs in your browser.
The third tab checks what you typed into ETABS' IS 1893 auto lateral load (Z, I, R, period) and works out the response spectrum scale factor clause 7.7.3 asks for. It opens on the 25-storey ETABS challenge building.
IS 1893 (Part 1):2016 with Amendments 1 and 2 · checked by an independent script · 1,141 learner reports read · Updated 21 Nov 2026
Site and system
Building (regular grid)
Members and loads per floor
Defaults: the "25 storey building" ETABS challenge (4 × 3 bays of 4 m, plinth at 1.5 m, 25 storeys of 3 m, 800 × 800 columns, 300 × 400 beams, 150 mm slab, 10 kN/m of infill on every beam, 3 kN/m² imposed, zone III, soil II). Walls go on every beam line; beams count below the slab; each column's weight is split half to the floor above and half below. Concrete 25 kN/m³. Roof imposed load is left out (7.3.2).
Period
"Period from" above picks the formula for Ta; "Your own T" uses the T typed here (for example a modal period). d is only used by 0.09 h/√d.
The building
What you typed into ETABS (auto lateral load)
Base reactions (kN), optional
Defaults: the inputs copied into 33 reports of the 25-storey challenge, a zone III building. Zone, soil, importance and system above are what the code needs; the boxes here are what was typed.
| Level | h (m) | Wi (kN) | Qi (kN) | Vi (kN) |
|---|---|---|---|---|
| Roof | 76.5 | 2,673 | 105.0 | 105 |
| Floor 25 | 73.5 | 3,297 | 119.6 | 225 |
| Floor 24 | 70.5 | 3,297 | 110.0 | 335 |
| Floor 23 | 67.5 | 3,297 | 100.8 | 435 |
| Floor 22 | 64.5 | 3,297 | 92.1 | 527 |
| Floor 21 | 61.5 | 3,297 | 83.7 | 611 |
| Floor 20 | 58.5 | 3,297 | 75.7 | 687 |
| Floor 19 | 55.5 | 3,297 | 68.2 | 755 |
| Floor 18 | 52.5 | 3,297 | 61.0 | 816 |
| Floor 17 | 49.5 | 3,297 | 54.2 | 870 |
| Floor 16 | 46.5 | 3,297 | 47.9 | 918 |
| Floor 15 | 43.5 | 3,297 | 41.9 | 960 |
| Floor 14 | 40.5 | 3,297 | 36.3 | 996 |
| Floor 13 | 37.5 | 3,297 | 31.1 | 1,027 |
| Floor 12 | 34.5 | 3,297 | 26.3 | 1,054 |
| Floor 11 | 31.5 | 3,297 | 22.0 | 1,076 |
| Floor 10 | 28.5 | 3,297 | 18.0 | 1,094 |
| Floor 9 | 25.5 | 3,297 | 14.4 | 1,108 |
| Floor 8 | 22.5 | 3,297 | 11.2 | 1,119 |
| Floor 7 | 19.5 | 3,297 | 8.4 | 1,128 |
| Floor 6 | 16.5 | 3,297 | 6.0 | 1,134 |
| Floor 5 | 13.5 | 3,297 | 4.0 | 1,138 |
| Floor 4 | 10.5 | 3,297 | 2.4 | 1,140 |
| Floor 3 | 7.5 | 3,297 | 1.2 | 1,141 |
| Floor 2 | 4.5 | 3,297 | 0.4 | 1,142 |
| Floor 1 | 1.5 | 3,057 | 0.0 | 1,142 |
- Plan 16.0 × 12.0 m, h = 76.5 m, 20 columns, 124.0 m of beams per floor.
- Ah = (0.16/2)(1.2/5)(0.701) = 1.346%; minimum 1.1% = 933 kN.
How to calculate base shear as per IS 1893:2016
The equivalent static method replaces the earthquake with a set of horizontal forces, one at each floor. Their total, the design base shear VB, is a fraction Ah of the building's seismic weight W:
- Z, the zone factor (Table 3): 0.10, 0.16, 0.24 and 0.36 for zones II to V. Halving it turns the maximum considered earthquake into the design basis earthquake.
- I, the importance factor (Table 8): 1.5 for important and critical buildings (hospitals, schools, emergency buildings), 1.2 for residential or commercial buildings with more than 200 occupants, 1.0 for the rest.
- R, the response reduction factor (Table 9): how much ductility the system is trusted to have. A special RC moment frame is 5.0, an ordinary one 3.0, and since Amendment 2 (2020) ordinary systems are allowed only in zone II.
- W, the seismic weight (clause 7.3): all the dead load plus 25% of the imposed load where it is up to 3.0 kN/m² and 50% above that (Table 10); no imposed load on the roof.
- ρ̄, the minimum (clause 7.2.2, Table 7): 0.7%, 1.1%, 1.6% and 2.4% of W for zones II to V.
Sa/g comes from the design spectrum at the building's approximate fundamental period Ta (clause 7.6.2). For a bare RC frame and for all other buildings:
For medium soil (type II) the equivalent static spectrum is below; rock has 2.5 up to 0.40 s then 1.0/T, soft soil 2.5 up to 0.67 s then 1.67/T. The response spectrum version starts at 1 at T = 0 and rises as 1 + 15T to the plateau at 0.1 s.
Finally the base shear is shared out over the height (clause 7.6.3), with the h² weighting that pushes force to the top:
Worked example: the 25-storey ETABS challenge building
A 16 × 12 m RC frame (4 × 3 bays of 4 m) with its plinth at 1.5 m and 25 storeys of 3 m above it, so h = 76.5 m. Columns 800 × 800 mm, beams 300 × 400 mm, a 150 mm slab, 10 kN/m of infill on every beam and 3 kN/m² imposed load. Zone III, soil type II. We take R = 5 (special RC moment frame) and I = 1.2 (a 26-level residential tower holds more than 200 people).
- One floor: slab 192 × 0.15 × 25 = 720.0 kN, beams 124 m × 0.3 × 0.25 × 25 = 232.5 kN, columns 20 × 0.8 × 0.8 × 25 × 3 = 960 kN, infill 124 × 10 = 1,240 kN: 3,152.5 kN dead. Add 25% of 192 × 3 = 144 kN imposed: 3,296.5 kN.
- Building: W = 84,845 kN over 26 levels (the plinth level carries 2.25 m of column, the roof half a storey and no imposed load).
- Period: Ta = 0.075 × 76.50.75 = 1.940 s, on the 1.36/T branch: Sa/g = 0.701.
- Ah = (0.16/2)(1.2/5)(0.701) = 1.346% of g, just above the zone III minimum of 1.1%.
- VB = 1.346% × 84,845 = 1,142 kN (with I = 1.0: 952 kN). Base overturning moment from these forces: 66,340 kN·m.
The roof takes 105 kN of it and the plinth level 0.0 kN. At 76.5 m in zone III this building needs a dynamic analysis, so 1,142 kN is the value its response spectrum base shear must reach.
Ta or the ETABS modal period?
The challenge brief expects a modal period of about 4.4 s in X and 4.2 s in Y. That is more than twice Ta = 1.94 s, which is normal: the empirical formula is meant to be a short, safe estimate, and a pinned-base model with no infill stiffness is flexible. The difference matters because Sa/g falls with T:
| Period used | Sa/g | Ah | VB (kN) |
|---|---|---|---|
| Ta = 1.94 s (clause 7.6.2) | 0.701 | 1.346% | 1,142 |
| Modal 4.4 s, Ah·W | 0.340 | 0.653% | 554 |
| Modal 4.4 s, minimum applied (1.1%) | 0.340 | 0.653% | 933 |
The design base shear uses Ta. A response spectrum run works with the modal periods, so its base shear comes out near the lower rows, and clause 7.7.3 scales it up to the Ta-based value:
Amendment 2 (2020) limits that scaling to forces: member forces, storey shears and base reactions are multiplied up, but displacements from the dynamic analysis need not be (clauses 7.7.3.2 and 7.11.1.2). The storey drift limit of clause 7.11.1.1 is 0.004 × the storey height under VB with all load factors at 1.0. The 2002 edition worked the other way: it scaled displacements too, and let the drift check use the computed period without the lower bound.
What 321 student ETABS models typed in
"Modelling of 25 storey building with the specified properties using ETABS" is a challenge in Skill-Lync's buildings programme. We read all 386 public reports (321 distinct texts, counts as of 20 Nov 2026), plus 272 distinct reports of the G+7 "Structural modelling using ETABS 2018" challenge.
- One set of earthquake inputs was copied 33 times. "Seismic zone factor as 0.36, importance factor 1.25 and time period 0.5 seconds", in a building the brief puts in zone III. Z = 0.36 is zone V, 1.25 is not an importance factor in IS 1893-1:2016 (it has 1.0, 1.2 and 1.5), and a user period of 0.5 s puts the building on the spectrum's plateau. With R = 5 that gives Ah = 11.250%: 8.4 times the code's 1.346%. Only 14 reports state the correct 0.16.
- The drift check inherits it. 229 reports discuss the clause 7.11.1.1 drift check, done under the unfactored seismic base shear. Storey drift is proportional to the lateral force, so a drift worked out under those inputs is about 8 times what VB gives; a "pass" still holds, but a "fail" may not be real.
- Few reports say how the period was set. 7 choose ETABS's "program calculated" period and none quote 0.075 h^0.75; only 6 state R. The 1,142 kN design value above needs Ta, not the modal period.
- The mass source is mostly right. 40 reports set live load at 0.25 in the mass source (3 kN/m² is not above 3.0, so 25% is right). 40 follow a copied line that takes "50% of the live load" on the roof. The brief puts 3 kN/m² on the roof too, and for the seismic weight the roof's imposed load need not be counted at all (clause 7.3.2).
- The response spectrum scaling is done in the right direction. In the G+7 challenge, 38 reports show the scale-factor sum and 37 of them scale up (EQ base shear above RS), as clause 7.7.3 asks. Only 5 cite the clause. The ratio has to use an EQ case built with Ta; built with the program period, it understates the scale-up.
Several reports share copied paragraphs, so the counts overstate independent mistakes; reports whose numbers sit only in images were not read.
Which edition: 2016 or 2025?
BIS published a seventh revision, IS 1893 (Part 1):2025, and then withdrew it: its "Know your standards" page lists the 2025 revision as withdrawn, and press reports in March 2026 say the 2016 edition is back in force. This calculator follows IS 1893 (Part 1):2016 with Amendment 1 (2017) and Amendment 2 (2020). If your project or course names a different edition, check the factors against it.
What this calculator does not cover
- The dynamic analysis itself. Apart from regular buildings under 15 m in zone II, the code needs a response spectrum (or time history) analysis; this tool gives the equivalent static value that result is scaled to, and the scale factor. The response spectrum analysis calculator does the modal analysis of a shear building.
- Torsion. The design eccentricity of clause 7.8.2 (1.5 esi + 0.05 bi) adds shear to the edge frames; the storey forces here act at the centre of mass.
- Exact masses. The building generator assumes one rectangular grid, walls on every beam and the same floor all the way up. For staircases, water tanks, lift machine rooms or setbacks, use the seismic weight from your model in the W box.
- Wall buildings. The period formula with Aw for RC structural walls (7.6.2 b) is not built in; type your own T.
- Irregularities and load combinations. Tables 5 and 6 decide when a building must be revised or analysed in 3D; the 1.2/1.5/0.9 combinations of clause 6.3 apply after this.
Skill-Lync's ETABS and high-rise courses take you from a model like this one to seismic design and detailing to IS 1893 and IS 13920, the work structural design firms hire for.
Frequently asked questions
How do you calculate base shear as per IS 1893:2016?
Work out the seismic weight W (all dead load plus 25% of an imposed load up to 3 kN/m², 50% above that, none on the roof). Find the approximate period Ta, for a bare RC frame 0.075 h^0.75, and read Sa/g from the design spectrum for your soil. Then Ah = (Z/2)(I/R)(Sa/g) and VB = Ah × W, but not less than the Table 7 minimum (0.7% to 2.4% of W). For the 25-storey ETABS challenge building in zone III that gives Ah = 1.346% and VB = 1,142 kN.
What is the formula for the time period in IS 1893:2016?
Clause 7.6.2: Ta = 0.075 h^0.75 for a bare RC moment frame, 0.080 h^0.75 for a composite frame and 0.085 h^0.75 for a steel frame, with h in metres. Buildings with RC structural walls use 0.075 h^0.75/√Aw, and all other buildings, including frames with masonry infill, use 0.09 h/√d, where d is the plan dimension at plinth level in the direction of shaking.
Why is the ETABS period different from 0.075 h^0.75?
ETABS' modal analysis gives the period of the model as built: a pinned-base frame with no infill stiffness is flexible, so the 25-storey challenge model comes out near 4.4 s against Ta = 1.94 s. The code formula is a deliberately short, safe estimate. The design base shear must use Ta (clause 7.7.3), because a longer period lowers Sa/g and with it the force.
What is the minimum base shear in IS 1893:2016?
Clause 7.2.2 and Table 7 set a floor of 0.7%, 1.1%, 1.6% and 2.4% of the seismic weight for zones II, III, IV and V. It is new in the 2016 edition. Tall, flexible buildings in low zones hit it first: a building whose Ah works out below 1.1% in zone III is designed for 1.1% of W.
What is the scale factor for response spectrum analysis in ETABS?
The scale factor turns the spectrum function into Ah = (Z/2)(I/R)(Sa/g). If your function holds Sa/g alone, the factor is Z·I·g/(2R); if the function already includes Z, it is I·g/(2R), for example 9,810 mm/s² × 1.2/10 = 1,177 for I = 1.2 and R = 5 in millimetre units. After the run, if the response spectrum base shear is below the equivalent static VB worked out with Ta, multiply the factor by VB/VRS for that direction (clause 7.7.3). The check tab here does this.
Can I use the equivalent static method for my building?
On its own, only for regular buildings less than 15 m tall in zone II (clauses 7.6 and 7.7.1). Every other building needs a dynamic analysis. But the static base shear is still needed for every building, because the dynamic results are scaled up to it.
What percentage of live load is taken for seismic weight?
Table 10: 25% of the imposed load where it is up to and including 3.0 kN/m², and 50% where it is above 3.0 kN/m². Imposed load on the roof is not counted (clause 7.3.2), though permanent equipment on it is.
What are the zone factors in IS 1893:2016?
Table 3: zone II 0.10, zone III 0.16, zone IV 0.24 and zone V 0.36. The formula halves Z to go from the maximum considered earthquake to the design basis earthquake.
Related on Skill-Lync
- ETABS project ideas and structural design courses compared
- Building load calculator (IS 875 dead and live loads, slab, wall, column)
- Steel structure load calculator (IS 875-3 wind on a portal frame)
- Shear wall design calculator (IS 13920 walls for these storey forces, and the centre of stiffness of the plan)
- Response spectrum analysis calculator (the modal analysis this base shear is scaled against: periods, modal mass, SRSS and CQC)
- Isolated footing design calculator
- Beam natural frequency calculator
- All free engineering tools
Sources
- Bureau of Indian Standards, IS 1893 (Part 1):2016 "Criteria for Earthquake Resistant Design of Structures, Part 1 General Provisions and Buildings", sixth revision, with Amendment 1 (2017) and Amendment 2 (2020): Public.Resource.Org copy. Tables 3, 7, 8, 9, 10; clauses 6.4.2, 7.2.2, 7.3, 7.4, 7.6, 7.7.1, 7.7.3, 7.8.2, 7.11.1.
- IS 1893 (Part 1):2002, fifth revision, law.resource.org, for the differences noted on this page.
- BIS "Know your standards": IS 1893 (Part 1):2025 (listed as withdrawn).
- CSI ETABS enhancements: v17.0.0 (2018) added auto-seismic loading and response spectrum functions to IS 1893:2016.
- 1,141 public Skill-Lync student reports on ETABS and TSD seismic challenges, read 20 Nov 2026 (counts above from the 25-storey and G+7 challenges).