Beam natural frequency calculator
Pick the supports, material and cross-section and get the first five natural frequencies and mode shapes of a uniform beam, with a tip mass on a cantilever, the static stiffness and the critical speed in rpm. Use it to size a part away from a forcing frequency, or to sanity-check an ANSYS or SOLIDWORKS modal analysis. Free, no sign-up, runs in your browser.
Euler-Bernoulli beam theory · roots match Blevins to 8 digits · checked against a finite-element model · Updated 17 Nov 2026
Bending in one plane, uniform section, small vibrations. For a rectangle, depth h is the dimension in the direction the beam vibrates: a ruler flaps in its thin direction. Tip mass applies to the cantilever only. Material values are typical handbook figures; edit them for your grade.
| Mode | λ = βL | f | rpm | Nodes (x/L) |
|---|
What is the natural frequency of a beam?
A beam has a natural frequency for each way it can bend: the first mode is one smooth bow, the second has one node (a point that stays still), the third two, and so on. Tap it and it rings at these frequencies. Shake it at one of them and the amplitude grows until something limits it, which is resonance. For a uniform, slender beam the frequencies follow from Euler-Bernoulli beam theory:
E is Young's modulus, I the second moment of area of the section about the bending axis, ρ the density, A the cross-section area (so ρA is the mass per metre) and L the length. Everything about the supports sits in λn, a root of the frequency equation for that support condition:
Two things follow from the formula. Frequency scales with 1/L², so halving a cantilever's length raises its first frequency four times. And for a given shape, √(E/ρ) is all the material brings: steel, aluminium 6061 and Ti-6Al-4V are within 1% of each other, because each is lighter in proportion to how much less stiff it is. Swapping steel for aluminium saves weight, not frequency; brass is about 30% lower.
λ values and node positions for every support
The roots of each frequency equation, the same five numbers you will find in Blevins' Formulas for Natural Frequency and Mode Shape (Table 8-1). The calculator solves the equations itself; these are its values, and the build checks them against Blevins and against a finite-element model.
| Supports | λ₁ | λ₂ | λ₃ | λ₄ | λ₅ | Nodes, mode 2 (x/L) |
|---|---|---|---|---|---|---|
| Cantilever | 1.8751 | 4.6941 | 7.8548 | 10.9955 | 14.1372 | 0.783 |
| Simply supported | 3.1416 | 6.2832 | 9.4248 | 12.5664 | 15.7080 | 0.500 |
| Fixed-fixed | 4.7300 | 7.8532 | 10.9956 | 14.1372 | 17.2788 | 0.500 |
| Fixed-pinned | 3.9266 | 7.0686 | 10.2102 | 13.3518 | 16.4934 | 0.557 |
| Free-free | 4.7300 | 7.8532 | 10.9956 | 14.1372 | 17.2788 | 0.132, 0.500, 0.868 |
Nodes include only the points inside the span, not the supports. Free-free modes exclude the two rigid-body motions (moving and rocking without bending) at zero frequency. A free-free beam's flexible frequencies equal a fixed-fixed beam's, though the mode shapes differ: that is why test labs hang parts on soft bungees to measure them.
Worked example 1: a steel ruler as a cantilever
The classic lab experiment: a 300 mm length of 25 × 3 mm steel strip clamped at one end, vibrating in its thin direction (E = 200 GPa, ρ = 7,850 kg/m³):
The higher modes come from the same formula with λ2 and λ3: 170.3 Hz and 477 Hz. They are 6.27 and 17.5 times the first, not 2 and 3 times as on a guitar string, because a beam's bending stiffness grows faster with mode number than its inertia does. The second mode's node sits 0.783 L from the clamp, 235 mm here: touch the strip there and the second mode survives while the first dies.
The same strip's stiffness at the tip, for a force pushing it sideways, is
and that is the first mode as a spring-mass system too: 1,250 N/m with a quarter of the strip's 177 g (33/140 of it) gives 27.58 Hz, 1.5% above the exact 27.18 Hz. For a spring and a mass on its own, use the spring-mass natural frequency simulator.
Worked example 2: checking a modal analysis
Before trusting a finite-element modal analysis of a real part, run it on a plain bar and compare with the formula. If the bar's numbers are off, the supports, units or mesh are wrong, not the theory. Take an aluminium 6061-T6 bar 500 mm long, 20 mm wide and 10 mm deep, clamped at both ends, bending across its 10 mm depth (E = 68.9 GPa, ρ = 2,700 kg/m³). The calculator gives 207.7 Hz, 572.5 Hz and 1122 Hz. A beam finite-element model, the cubic Euler-Bernoulli element from FE textbooks with a consistent mass matrix, gets there as the mesh is refined:
| Elements | Mode 1 | Mode 2 | Mode 3 |
|---|---|---|---|
| 2 | 211.1 Hz (+1.6%) | 761.0 Hz (+32.9%) | n/a |
| 4 | 208.0 Hz (+0.13%) | 577.8 Hz (+0.92%) | 1146.4 Hz (+2.1%) |
| 8 | 207.7 Hz (+0.008%) | 572.9 Hz (+0.063%) | 1125.1 Hz (+0.24%) |
| 16 | 207.7 Hz (+0.001%) | 572.6 Hz (+0.004%) | 1122.6 Hz (+0.015%) |
| Formula | 207.7 Hz | 572.5 Hz | 1122.4 Hz |
Two lessons from the table. A finite-element model is too stiff, so its frequencies come out high and fall towards the answer as you refine. And the higher modes need a finer mesh: 4 elements are already within 0.13% on mode 1 but 2.1% high on mode 3. Mesh until the highest mode you report stops moving. A solid-element model of the same bar in ANSYS or SOLIDWORKS also includes shear and the Poisson effect, so for a slender bar like this expect agreement within about 1%, and lower frequencies than the formula for stubby parts. The student project Modal analysis using Ansys Workbench walks through the free-free, fixed and prestressed set-ups.
Worked example 3: a cantilever with a mass at the end
A sensor bracket: an aluminium 6061-T6 strip 150 mm long, 20 × 3 mm, clamped at one end with a 100 g sensor on the free end. The strip itself weighs 24.3 g, so the tip mass is μ = 4.1 times the beam's. The exact frequency equation picks up a tip-mass term:
which gives f1 = 25.69 Hz, down from 108.8 Hz for the bare strip. Rayleigh's quick estimate treats the strip as a spring with 33/140 of its mass riding at the tip:
Here it gives 25.70 Hz (0.004%). Ignoring the strip's mass altogether gives 26.42 Hz, 2.8% high. Rayleigh is good whenever the tip mass dominates, and worst for a bare beam:
| Tip mass / beam mass | 0 | 0.1 | 0.5 | 1 | 2 | 5 | 10 |
|---|---|---|---|---|---|---|---|
| Rayleigh error, mode 1 | +1.5% | +0.72% | +0.15% | +0.053% | +0.016% | +0.003% | +0.001% |
A heavy tip mass also pulls the second mode down far less than the first (484 Hz here), so the gap between them widens and the beam behaves more and more like one spring and one mass, the assumption behind tuned cantilever vibration absorbers and energy harvesters.
Worked example 4: critical speed of a shaft
A uniform steel shaft, 30 mm in diameter, with bearings 1200 mm apart. Treating the bearings as pins, the first bending mode is 41.30 Hz and the first critical speed is
Designs keep the running speed well clear of it, and a machine that runs above it passes through it quickly at start-up. Timoshenko theory changes this slender shaft (L/d = 40) by only 0.08%. Bearings that are not rigid pins lower the speed; discs and pulleys lower it further, and their gyroscopic effect splits it into forward and backward whirl, which this calculator does not model.
When the formula over-predicts: short, deep beams
Euler-Bernoulli theory assumes plane sections stay square to the beam's axis, so it ignores shear deformation and the inertia of the sections rotating. Both matter when the beam is short compared with its depth, and more for higher modes, because those have shorter wavelengths. Timoshenko beam theory includes both. For a simply supported steel beam of rectangular section (shear coefficient κ = 0.850, Cowper), Euler-Bernoulli is high by:
| L / h | Mode 1 | Mode 2 | Mode 3 |
|---|---|---|---|
| 3 | +16.3% | +51.9% | +94.8% |
| 5 | +6.3% | +22.4% | +44.0% |
| 10 | +1.6% | +6.3% | +13.5% |
| 20 | +0.4% | +1.6% | +3.6% |
Below about L/h = 10, or for modes above the first two, use a Timoshenko beam or a solid finite-element model. The calculator computes this check for your beam (as if simply supported, with your section's shear coefficient) and warns you once the gap passes 2%.
What this calculator does not cover
- Axial load. Tension raises bending frequencies and compression lowers them, to zero at the buckling load.
- Non-uniform beams. Tapered or stepped sections, holes and attached masses other than one at a cantilever's tip need a finite-element model or Rayleigh-Ritz.
- Flexible supports. Real clamps, bolted joints and bearings are not perfectly rigid; they lower the frequencies, sometimes a lot.
- Other mode families. Torsional, axial and out-of-plane (sideways) bending modes. For a rectangle, run the calculator again with b and h swapped for the other bending plane.
- Plates, shells and damping. Wide, thin parts behave as plates; damping barely shifts natural frequencies but sets the peak amplitude at resonance.
Skill-Lync's FEA courses take you from beam formulas to modal, harmonic and dynamic analysis of real parts in Ansys and SOLIDWORKS, the work CAE teams hire for.
- Structural Analysis using Ansys Workbench (7 weeks; week 5 is dynamics and modal analysis)
- FEA using SOLIDWORKS (4 weeks, includes frequency analysis)
- Post Graduate Program in CAE (48 weeks)
Frequently asked questions
What is the formula for the natural frequency of a cantilever beam?
f_n = (λ_n² / 2πL²) √(EI/ρA), with λ_1 = 1.8751, λ_2 = 4.6941 and λ_3 = 7.8548 for a cantilever. A 300 mm steel strip 25 × 3 mm vibrating in its thin direction has f_1 = 27.18 Hz, f_2 = 170.3 Hz and f_3 = 477 Hz. The second mode is 6.27 times the first, not 2 times as for a string.
What is the stiffness of a cantilever beam?
For a point load at the free end, k = 3EI/L³ (deflection δ = FL³/3EI). The 300 mm × 25 × 3 mm steel strip has k = 1,250 N/m, about 1.25 N/mm. A simply supported beam loaded at midspan has k = 48EI/L³, a fixed-fixed one 192EI/L³ and a propped cantilever (768/7)EI/L³ at midspan.
How do you find the natural frequency of a beam with a mass at the end?
Solve the cantilever's frequency equation with the tip-mass term, or use Rayleigh's estimate f ≈ (1/2π)√(k / (M + 0.236 m_beam)) with k = 3EI/L³. Rayleigh's estimate is within 0.7% of the exact first frequency when the tip mass is a tenth of the beam's mass and within 0.05% when they are equal. This calculator gives the exact value.
How do I check an ANSYS or SOLIDWORKS modal analysis?
Model a simple bar of the same length, section and supports and compare the first few frequencies with this calculator. A converged solid or beam model of a slender bar should agree within about 1%. In the fixed-fixed aluminium example, a 4-element beam model is 2.1% high in the third mode, so refine until the modes you care about stop changing. Short, deep parts will come out lower than this calculator, because it ignores shear (see the Timoshenko table on this page).
What is the critical speed of a shaft?
The first bending critical speed of a uniform shaft on two bearings is roughly its first natural frequency as a simply supported beam, times 60 for rpm. A 30 mm steel shaft with bearings 1200 mm apart: 41.3 Hz, about 2,478 rpm. Real bearings are not perfect pins, and discs, couplings and gyroscopic effects change it, so treat this as a first check.
Why does a fixed-fixed beam have a higher frequency than a simply supported one?
Clamping both ends stops the ends rotating, which stiffens the beam in bending: λ_1 rises from π (3.1416) to 4.7300, and frequency goes with λ², so the fixed-fixed beam's first mode is 2.27 times the simply supported one. A cantilever, with one free end, is much lower: (1.8751/π)² = 0.356 times.
When is the Euler-Bernoulli beam formula not accurate?
When the beam is short and deep, or for higher modes. For a simply supported steel beam of rectangular section, Euler-Bernoulli over-predicts the first frequency by 1.65% at L/h = 10 and 6.3% at L/h = 5, and the third mode by 13.5% at L/h = 10, against Timoshenko beam theory, which adds shear deformation and rotary inertia. The calculator warns you when the gap passes 2%.
Related on Skill-Lync
- Understanding frequency analysis in SOLIDWORKS FEA
- Student project: modal analysis using Ansys Workbench
- Ride frequency and motion ratio calculator
- 0.2% offset yield strength calculator
- FEA courses compared
- All free engineering tools
Sources
- R. D. Blevins, Formulas for Natural Frequency and Mode Shape, Van Nostrand Reinhold 1979 / Krieger reprint, Table 8-1 (λ values, mode shapes and node positions of uniform single-span beams).
- S. S. Rao, Mechanical Vibrations, Pearson, chapter on continuous systems (Euler-Bernoulli frequency equations, cantilever with a tip mass, Rayleigh's method, Timoshenko beam).
- G. R. Cowper, "The shear coefficient in Timoshenko's beam theory", Journal of Applied Mechanics 33 (1966) 335-340 (κ for rectangle, solid circle and thin tube).
- Material values: IS 800:2007 clause 2.2.4.1 for structural steel (E = 2 × 10⁵ N/mm², ν = 0.3, 7,850 kg/m³); ASM Aerospace Specification Metals / MatWeb data sheets for 6061-T6, Ti-6Al-4V, 304 stainless and C26000 brass.
- Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/beam_modes.py, a finite-element beam (240 cubic elements, consistent mass, eigenvalues by Sturm-sequence bisection, no frequency equations) that matches every λ in the table to better than 1 part in a million, and cross-checked against this page's calculator code at build time.