Response spectrum analysis calculator (modal, IS 1893)

Find the natural periods and mode shapes of a shear building, its modal participation factors and effective modal masses, how many modes reach 90% of the mass, and the floor forces, storey shears, displacements and base shear of a response spectrum analysis with the IS 1893:2016 spectrum, an ASCE 7 spectrum or your own. Combine by SRSS, CQC or ABSSUM, scale to the static base shear, and check your answers to the ETABS Degrees of Freedom challenge. Free, no sign-up, runs in your browser.

IS 1893 (Part 1):2016 cl 6.4.2, 7.7.3 and 7.7.5 with Amendments 1 and 2 · Wilson's CQC table · IITK-GSDMA Example 2 · checked against an independent solution (10,907 checks at build) · Updated 22 Nov 2026

Floors (1 = first floor above the base)

Storey stiffness from the columns

Fundamental periodT1 = 2.000 sf1 = 0.500 Hz
Modes for 90% mass296.67% with 2
Mode 1 mass87.96%Γ1 = 1.0672
Mode shapes 1 to 5 drawn against floor heightMode 1T 2.000 sMode 2T 0.685 sMode 3T 0.435 sMode 4T 0.338 sMode 5T 0.297 sF1F2F3F4Roof
ModeT (s)f (Hz)MnLnΓnMn*%Σ%

    What is response spectrum analysis?

    Response spectrum analysis finds the peak earthquake response of a building mode by mode and then combines the modes. Each mode behaves like a single-storey oscillator with its own period; the design spectrum gives its peak acceleration An; the mode's participation decides how much of the building's mass it moves. IS 1893:2016 cl 7.7.1 requires it, or a time history analysis, for every building except regular ones under 15 m in zone II.

    For a shear building (rigid floors, columns that only bend, one sideways degree of freedom per floor) the mass matrix is diagonal and the stiffness matrix is tridiagonal, so the whole analysis fits in a few lines. This is the model of the Degrees of Freedom challenge and of IS 1893's simplified method (cl 7.7.5.4). ETABS does the same with a full 3D model.

    How many modes are needed? The 90% rule

    IS 1893:2016 cl 7.7.5.2: enough modes that "the sum total of modal masses of these modes considered is at least 90 percent of the total seismic mass", in each direction of shaking. Modes above 33 Hz are not combined; their effect is added by a missing mass correction. In ETABS this is the "Sum UX" (or UY) column of the Modal Participating Mass Ratios table.

    A uniform shear building puts about 88% of its mass in mode 1 whatever its height, which is why the five-storey challenge needs two modes (87.96%, then 96.67%). A soft ground storey concentrates the deformation there and pushes mode 1 up: our 10-storey preset has 94.76% in mode 1. The IITK-GSDMA building has 92.6%, so one mode meets the rule; the example combines three anyway.

    SRSS or CQC: how are the modes combined?

    The modal peaks do not occur at the same instant, so they are not added. IS 1893:2016 cl 7.7.5.3 (a) gives the complete quadratic combination, with ζ = 0.05:

    When no two modes are closely spaced (frequencies within 10% of the lower one, cl 3.1), cl 7.7.5.3 (b) allows the square root of the sum of squares instead: ρij is close to zero off the diagonal and CQC becomes SRSS. For the challenge, CQC gives 1.1910 W against SRSS 1.1861 W. For two modes 9% apart in our close-mode test, ρ12 = 0.666 and CQC is 29% above SRSS: in a building with similar periods in two directions or in torsion, SRSS is unsafe. The absolute sum (ABSSUM) is an upper bound; cl 7.7.5.3 (b)(2) uses it only within a group of closely spaced modes.

    The formula matches Wilson's Table 15.1 (five frequencies, ζ = 0.05) to the printed three decimals in 24 of 25 entries; ρ35 comes out 0.179 against 0.180 because the table's frequencies are rounded.

    Combine storey shears, not floor forces

    Every response quantity is computed mode by mode and combined at the end. For a mode, the floor forces, base shear and displacements are:

    The common slip is to take SRSS of each floor's force and then add the floors. Modal forces change sign up the height in the higher modes; squaring throws those signs away, so the sum is too large. IS 1893:2016 cl 7.7.5.4 (e) and (f) combine the storey shears, then get the floor forces back as Froof = Vroof and Fi = Vi − Vi+1. In the challenge building the wrong way gives 1.878 W at the base against 1.1861 W, 58% too high. Tab 2 shows both columns for any building.

    Scaling to the static base shear (IS 1893 cl 7.7.3)

    The dynamic base shear VB may not be less than V̄B, the equivalent static base shear computed with the empirical period Ta of cl 7.6.2. When it is, the force quantities (member forces, storey shears, base reactions) are multiplied by V̄B/VB (cl 7.7.3.1). Since Amendment 2 (2020) the displacements need not be scaled (cl 7.7.3.2). Type V̄B in tab 2 to get the factor; the seismic base shear calculator gives V̄B and checks an ETABS response spectrum scale factor.

    Worked example: IITK-GSDMA EQ21 Example 2

    S. K. Jain's "Explanatory Examples on Indian Seismic Code IS 1893 (Part I)" (IITK-GSDMA-EQ21), Example 2, analyses a four-storey building in Shillong (zone V, Z = 0.36, I = 1, R = 5) with floor weights 4,200, 4,200, 4,200 and 3,000 kN, from given periods 0.860, 0.265 and 0.145 s and roof-normalised mode shapes. Choose it in tab 1. The calculator reproduces its Table 2.2: ΣWφ = 11,656, −2,905 and 1,366; Mk = 14,450, 957 and 161 kN/g (92.6%, 6.1%, 1.0%); Pk = 1.240, -0.329 and 0.118.

    For mode 1 the example takes Sa/g = 1.0/0.86 = 1.16, the rock branch, although the building stands on medium soil (1.36/T would give 1.58); the preset follows the example so the numbers can be compared, and "eq21-medium" in the verifier gives 827 kN on medium soil. With the example's rounded Ah1 = 0.0418 and three-decimal Pk its Table 2.3 floor forces follow to 0.1 kN, and the SRSS storey shears are 182, 371, 510 and 610 kN, as printed (182, 371, 510, 610). Unrounded, the calculator gets 611.2 kN. Against the static 1,404 kN the scale factor is 1,404/610 = 2.30; the example's second reading, mode 1 re-run at Ta, gives 1,303 kN and 2.14.

    The Degrees of Freedom challenge: worked solution

    The challenge is Skill-Lync's ETABS / Buildings assignment "Understanding the concepts on Degrees of Freedom": a five-storey shear building with mass m at every floor, the periods and mode shapes given. The shapes are 1.185 sin((2n − 1)πj/11) to three decimals, the exact modes of a uniform five-storey shear building, and the periods follow from T1 = 2 s with k/m = 121.8 s⁻² (the "dof-km" preset solves it from scratch and gets the same numbers). Mode 1:

    ModeT (s)Mn (m)Ln (m)ΓnMn* (m)%Σ%An (g)Vbn (W)
    123.86154.1211.06724.398087.9687.960.25751.1325
    20.68523.8615-1.297-0.33590.43568.7196.670.75160.3274
    30.43463.86150.6830.17690.12082.4299.091.03000.1244
    40.33833.8615-0.381-0.09870.03760.7599.841.03000.0387
    50.29663.86150.1750.04530.00790.16100.001.03000.0082

    The figure's spectrum is a code-shaped design spectrum. We traced its curve pixel by pixel and fitted the ASCE 7-16 cl 11.4.6 shape: SDS = 1.0278 g, SD1 = 0.5147 g, TL = 1.991 s and a ramp ending at T0 = 0.153 s (not ASCE's 0.2 SD1/SDS = 0.1 s), with 0.0017 g rms and 0.0068 g largest error over 486 columns. So SDS = 1.03 g, SD1 = 0.515 g and TL = 2 s: mode 1 sits exactly at the corner where SD1/T turns into SD1TL/T², A2 is on the 1/T branch and modes 3 to 5 are on the 1.03 g plateau. Reading 0.27 g at 2 s, as most reports do, gives Vb1 = 1.187 W and an SRSS of 1.24 W; the graph reading alone moves the answer by about 4%.

    What the reports do

    We read the 373 public reports of the challenge on 22 Nov 2026; 126 show their working in text (the rest are images), and the counts below are out of those that state each number.

    • The modal properties are mostly right. 115 write Mn = 3.86m, 112 L1 = 4.12m, 107 Γ1 = 1.067, 118 M1* = 4.40m and 101 give mode 1 88% of the mass. 75 keep the minus sign of Γ2; 3 drop it. Of the 97 that say how many modes reach 90%, 95 say two and 2 say one.
    • An by eye. 38 of the 44 that write A1 read 0.27 g (the curve is at 0.2575 g); 33 of 42 read A2 = 0.76 g (curve 0.7516 g). Both are fair readings.
    • The combined base shear. 50 reports state the SRSS base shear. 26 of them write 1.15 W, yet the Vbn they list (1.187, 0.327, 0.126, 0.0385, 0.008) give √ΣVbn² = 1.24: an arithmetic slip repeated across 26 reports. 13 write 1.23 to 1.24 (right for A1 = 0.27 g) and 5 write 1.27 to 1.28 (from A1 = 0.279 g).
    • A base shear written as a mass. Of the 35 that give Vb1 a unit, 21 write "1.187m". Mn*An with An in g is 1.187 mg = 1.187 W, a force.
    • Few go past the base shear. 1 computes floor displacements, 1 cites IS 1893 and none mentions CQC.

    Tab 3 flags each of these in your own numbers.

    How we checked the calculator

    An independent Python script, scripts/verify/modal_rs.py, rebuilds every calculation, and this page refuses to build if the browser code differs from it in any of 10,907 numbers (856 further assertions run inside the script). The script solves the eigenproblem with LAPACK's generalised solver (scipy eigh) where the browser uses Jacobi rotations; checks the closed form ωn = 2√(k/m) sin((2n − 1)π/(2(2N + 1))) and its sine mode shapes for 1 to 10 storeys; reproduces IITK-GSDMA EQ21 Example 2 (Tables 2.2 and 2.3, the SRSS shears, both scale factors), the participation factors and modal masses of IITGN-WB-EQ3 Example 6 and Wilson's CQC table; and runs ten random non-uniform buildings through every quantity on this page. Two deliberate bugs (Mn* = Ln/Mn, and ζ² written as ζ in ρ) each make it fail.

    What this calculator does not cover

    • 3D buildings. One sideways degree of freedom per floor: no torsion, no accidental eccentricity (cl 7.8.2), no flexible floors. Use ETABS for those; this is the hand check.
    • Shear building stiffness. The column helper assumes rigid beams (12EI/h³) or pinned tops (3EI/h³); real frames with flexible beams sit in between.
    • Missing mass. Modes above 33 Hz (cl 7.7.5.2) are combined like the rest; the missing mass correction is not applied.
    • Closely spaced modes. The page flags pairs within 10% and gives CQC; it does not apply the ABSSUM-within-a-group rule of cl 7.7.5.3 (b)(2).
    • Damping. IS 1893:2016 fixes 5% (cl 7.2.4) and has no damping table; the other values use the 2002 edition's Table 3 factors.
    Learn building design

    The Degrees of Freedom challenge is part of Skill-Lync's ETABS and high-rise building design courses, next to seismic analysis, shear wall design and SAFE foundations.

    Frequently asked questions

    What is the difference between modal mass and effective modal mass?

    The generalised (modal) mass Mn = φn'mφn depends on how the mode shape is scaled. The effective modal mass Mn* = Ln²/Mn does not: it is the part of the total mass that moves in mode n, and all modes add up to the total. IS 1893 calls Mn* the modal mass Mk (cl 7.7.5.4).

    What is the modal participation factor?

    Γn = Ln/Mn says how much of mode n the ground motion excites. It depends on how φn is scaled (IS 1893:2016 cl 3.15), but Γnφn does not. For the Degrees of Freedom challenge's shapes Γ1 = 1.0672 and Γ2 = -0.3359; the sign matters for floor forces, not base shear.

    How many modes should be considered in response spectrum analysis as per IS 1893?

    Enough modes for their effective modal masses to add up to at least 90% of the total seismic mass, in each direction (IS 1893:2016 cl 7.7.5.2). Modes above 33 Hz are not combined; their effect enters through a missing mass correction. In the five-storey challenge mode 1 has 87.96%, so two modes are needed.

    What is the difference between SRSS and CQC?

    SRSS squares each modal peak, adds and takes the root, assuming the modes are independent. CQC adds cross terms weighted by a correlation ρij that grows as two frequencies approach each other. For well separated modes they agree; for closely spaced modes (within 10%, IS 1893 cl 3.1) SRSS can be badly unconservative.

    Why is the response spectrum base shear lower than the static base shear in ETABS?

    The modal analysis uses the computed period, which is usually longer than the code's empirical Ta, so it reads a lower spectral value. IS 1893:2016 cl 7.7.3 then asks you to scale force results up by V̄B/VB; displacements need not be scaled (7.7.3.2, Amendment 2).

    Does the participation factor depend on mode shape normalisation?

    Yes. Doubling a mode shape halves Γn and quadruples Mn, but Γnφn, Mn* and every response quantity stay the same. That is why roof = 1, max = 1 and mass-normalised shapes give different Γ but the same base shear. Tab 1 shows this live.

    Is this response spectrum calculator free?

    Yes. It runs in your browser with no sign-up, and nothing you type is sent anywhere. It reproduces IITK-GSDMA Example 2 and Wilson's CQC table, and the page will not build if the browser code and an independent Python check disagree on any of 10,907 numbers.

    Related on Skill-Lync

    Sources

    • Bureau of Indian Standards, IS 1893 (Part 1):2016 Criteria for Earthquake Resistant Design of Structures, Part 1, cl 3.1, 3.14, 3.15, 6.4.2, 7.2.4, 7.7.1, 7.7.3, 7.7.5 with Amendments 1 (2017) and 2 (2020); IS 1893 (Part 1):2002 Table 3 (damping factors). The 2025 revision was withdrawn.
    • Bureau of Indian Standards, IS 456:2000, cl 6.2.3.1 (E = 5000√fck).
    • E. L. Wilson, Three-Dimensional Static and Dynamic Analysis of Structures, 3rd ed., CSI, eq. 15.10 and Table 15.1.
    • S. K. Jain, Explanatory Examples on Indian Seismic Code IS 1893 (Part I), IITK-GSDMA-EQ21-V2.0, Example 2; S. K. Jain, O. R. Jaiswal, R. K. Ingle and D. C. Rai, Examples on IS 1893 (Part 1):2016, IITGN-WB-EQ3-V3.0 (2019), Examples 2 and 6.
    • Skill-Lync, the 373 public reports of the Degrees of Freedom challenge, read 22 Nov 2026.
    Free counselling

    From a modal analysis challenge to a structural design job.

    Response spectrum analysis, ETABS and IS 1893 are what building design consultancies test for. A Skill-Lync counsellor can map the course that fits the role you want.

    Talk to a structural design course counsellor

    Free. We call you back, usually the same day.

    By submitting you agree to our Terms and Privacy Policy.

    Talk to a career counsellor

    Talk to a career counsellor

    Free 20-minute call. We'll map the right course to where you want to work.

    By submitting you agree to our Terms and Privacy Policy.