Week 9 - Attachment Feature Creation - Challenge 2

Objective: To Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. To Check the harness Continuity using search option in CATIA V5  Given DATA: The Backdoor DATA was…

Objective: To Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. To Check the harness Continuity using search option in CATIA V5  Given DATA: The Engine DATA was downloaded…

Step 1: Create a Product File and define the Flatening Parameter by clicking on the Flatening Parameter Icon.           Step 2: Click Extract Icon to extract the wiring harness assembly that we want to flatten.    Step 3: Once the file is inserted, selct flatten command and click the branches to flatten. Make sure to turn…

1. Firstly, Download all the connector files and Define the connector connection point and bundle points in all the connectors in Electrical part design.       2. Create a seperate product file for Harness A and Harness B, and place the connectors according to the given layout.             3. Define the ASM A and B as…

Step 1: Create a product file for Wiring harness and create a geomentric bundle asm inside the wiring harness ASM. A Fixing plate is created in another product file to place the connectors over the plate. Step 2: Define the Connectors in the Electrical part design and define the connector connection point and bundle connecction…

3.            1. Create geomentric planes at cable entry and exit and also the base plane. Define it as electrical support in electrical part dsign workbench.   2.  Define geomentric elemnts and define backshell connection point at the front and bundle connection point at the back.…

  1. First step is to create a point for bundle entry point and connector connection point and defining it in electrical part workbench. 2. Define the bundle entry point in the electrical part design. 3. Define the connector connection Point. 4. Define Cavity Connection Point. 5. Define cavity for mounting clip , by first…

Objective:To design the Back door of a car from the provided Styling surface by implementing appropriate design methodologies.To design the inner panel reinforcements and creating embosses on the inner panel.To find out the hinge axis and Latch and striker trajectory. Back Door of a Car:A car door is a type of door…

Objective: To Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs. To Calculate the Heat distortion and snow load criterion for the roof. To create front roof rail, rear roof rail, bow roof 1 and bow roof 2 according to the master section. To perform draft analysis on the…

Objective: To design the front fender of a car from the given Class A surface. To create the drip area from the given master section dimensions. To create Sill, Bumper, Baffle (Splash), and A-Pillar mountings. Fender Design Methodology. Fender is the American English term for the part of an automobile, motorcycle or other…

Objective: To Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. Fender wheel Regulations: Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent…

Objective: To study the section modulus of the Hood assembly using NX section interface tools and to optimize the results from the output data of sectional modulus. Sectional Modulus Definition: Section Modulus is a geometric property used to calculate the bending stresses in a structural member. Mathematically, It is…

Week 1- Hood Design Challenge Objective: Design Hood Outer Panel, Inner Panel, and the necessary reinforcements by following the Master Section mentioned with the Design parameters. Convert the surface data to a thickened BIW sheet. Create embosses on the outer panel using NX Commands. Create a Hemming flange and hemming…

Under body coating is a finishing process , which is applied to the car under body either in paint or spray form. In Indian road conditions, a cars underbody is most prone to corrosion. Underbody coating provides long term protection from corrosion to car’s underbody. It also protects parts like internal body…

Problem statement: Mr. Pughazyendi lives in banglore along with his family members which comprises of 5 people. He is willing to buy a car for his regular commute to office and also to visit his native once in a month. Through this report , we will be coming up with a proper suggestion, by carefully studying the automotive…

.

,,,