Week 7 Challenge - Assembly Workbench

AIM                To route the Wiring Harness on given Tailgate / Backdoor and Flatten view drawing in CATIA V5.   OBJECTIVE              The objective of the project is to route the wiring harness on given Car Backdoor and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while…

AIM           To route the Wiring Harness on given Car Door and Flatten view drawing in CATIA V5.   OBJECTIVE          The objective of the project is to route the wiring harness on given Car Door and prepare flatten view drawing in CATIA V5. All types of packaging…

AIM          To Flatten the harness assembly completed in “week 4 challenge” then place it in the Flattened view on drawing sheet and also Ensure bundles with protective coverings has Different Visuals on drawing view.   INTRODUCTION         Electrical Harness Flattening is a product which is intended to flatten 3D harnesses…

AIM          To Route two Electrical Harnesses as per given Layout and Interconnect them Single Harness Assembly and then check for bundle continuity, bundle warnings, and further give annotations to the final harness assembly.   INTRODUCTION Wiring Harness          …

AIM          To Download Connectors – DT06-2S, DT06-4S, DT06-6S, DT06-08SA, cad data from given link & defining them Electrically, and further Routing them as per given Layout and adding Protective Covering on all branches, keeping end extremity at 30mm.   INTRODUCTION Wiring Harness           A wire harness is a specially…

AIM          To Download Routing & Packaging Components – P clips, Backshells, Corrugated Tubes, cad data from given link & defining them Electrically using Electrical Part design Workbench, defining all the necessary properties to components and further creating Catalogue…

AIM          To Download Connectors & Connector clip cad data from given link & defining them Electrically using Electrical Part design Workbench, defining all the necessary properties to Connectors & Clip and creating the electrical assembly and further creating Catalogue…

AIM          To create Door Trim Panel Assembly by creating individual components through a given Class A Surfaces - Arm Rest, Upper Map Pocket, Lower Map Pocket, Lower Substrate and Using given Master section to create B Side features – Locators, Heat stakes, Dog Houses in…

AIM          To create A Pillar’s Plastic Component through a given Class A Surface and Using given Master section to create B Side features, considering design rules and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create the…

AIM          To create a Door Trim Lower Plastic Component through a given Class A Surface, create the Heat Stakes, Locators considering design rules and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements…

AIM          To create a Door Trim Plastic Component through a given Class A Surface, create the Dog house (attachment feature) and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create the Tooling axis using bisecting method…

AIM          To create a Drill handle Plastic Component through a given Class A Surface, create the ribs and screw bosses and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create…

AIM  To create assembly of Quick return mechanism and CV joint and to also create 2D drawing of the given assembly.   ASSEMBLY  Assembly modeling is a technology and method used by computer-aided design and product visualization computer software systems to handle multiple files that represent components…

AIM          To create a Bumper Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create the Tooling axis using bisecting method.…

AIM          To create a Switch Bezel Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create the Tooling axis using bisecting method. To perform Draft analysis on the given…

AIM          To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component.   OBJECTIVE To make sure that the model meets the requirements of the draft angle. To create the Tooling axis using bisecting method. To perform Draft analysis on the given…

AIM                To design the back door of a car from the styling surface provided using NX CAD. The ultimate aim is to design the back door as per the industrial standards. INTODUCTION           A back…

DESIGNING OF ROOF USING NX-CAD   INTRODUCTION           An automobile roof is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Though it just looks like a styling surface that protects from sun, wind and other elements,…

OBJECTIVE             To design the mounting areas of front fender of BIW using the fender skin data and as per master section given using NX CAD. FENDER               Fender is the part of an automobile…

OBJECTIVE             To find the section modulus of the hood and optimisation to improve the overall section modulus. SECTION MODULUS             It is termed as the ratio of the second moment of area and distance…

TASK 1 FENDER WHEEL ARCH REGULATIONS   FENDER               Fender is the part of an automobile vehicle body that frames a wheel well. Its primary function is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by…

HOOD DESIGN USING NX   In this report, the flow of information will be as follows: Objective Introduction Data Design of components Analysis Conclusion   OBJECTIVE            Design hood outer panel, inner panel, and reinforcements with the given outer hood skin,…

REQUIREMENTS: UNDER BODY COATING, ITS TYPES ITS PROS AND CONS     ABOUT UNDER BODY COATING                          Underbody coating is usually a dense cladding (often based on rubber) applied…

1. TASK - PRESENTATION OUTLINE  BENCHMARKING MEANING BENCHMARKING DEFINITION BENCHMARKING FEATURES WHY BENCHMARKING BENCHMARKING ADVANTAGES AND DISADVANTAGES BENCHMARKING PROCESS BENCHMARKING TYPES WHAT IS BENCHMARKING? At its simplest, benchmarking means:                                …