Week 4.1 - Genetic Algorithm

AIM: To write a code in MATLAB to optimize stalagmite function and find the global Maxima of the same. THEORY: DEFINITION: GENETIC ALGORITHM is a search heuristic that is inspired by Charles Darwin theory of natural evolution. This algorithm reflects the process of natural selection where fittest individuals are selected…

                                                   DESIGN OF AMERICAN CHOPPER   INTRODUCTION           This Report Contains brief explanation…

AIM              Design of Radar mast using Solidworks. FRONT VIEW TOP VIEW SIDE VIEW ISOMETRIC VIEW TREE STRUCTURE    SURFACE MODELLING OF SUNSEEKER PREDATOR YACHT ASSEMBLY AND RENDER . ABSTRACT                   The…

Underbody coating:  Undercoating is the sprayed application of a wax or rubber-based composite onto the entire underside of the vehicle. It's designed to create a rust-proof layer between the underside of the vehicle and the water, ice, and salt of the road. Undercoating provides a more comprehensive protective…

Benchmarking:                       Benchmarking involves a structured comparison between similar products, services, or processes on some dimensions of performance.  Problem Statement:                     Mr D.S.…

AIM:               To write a program that solves the equation of the motion of a simple pendulum with damping. CONCEPT: For a simple pendulum with a damping factor, the equation of simple pendulum is Where             b = damping…

AIM: To create 2 assemblies according to the content covered in the course videos. You will be provided with 2D diagrams of the components and you will have to first create the individual part files and then create a complete assembly of those part files in the assembly workbench. After creating the assembly, use the drafting…

DESIGNING A B-PILLAR AIM:        To design a B-pillar from the provided class-A surface and master-section as inputs. PILLARS IN CAR:       The vertical roof support structure located between the front and rear doors on a typical vehicle. It corresponds with the A-pillar located…

OBJECTIVE Design the Driver Door Right Hand Applique with Locators and Fixtures to assemble it onto the main inner door panel. LOCATION PRINCIPLE The 3-2-1 or 6 Point Location principle is used to constrain the movement of the workpiece (to be machined/fixed) along the 3 axes XX, YY, and ZZ. It is achieved by providing…

                CREATE THE BOSS AND DOG HOUSE FOR THE CENTER CONSOLE COIN HOLDER   OBJECTIVE –             To create Screw Boss and Dog House on Coin Holder Based on the Design Consideration Using CATIA. SCREW BOSS CREATION –…

DESIGN RULES FOR RIBS CREATION AIM:  to design ribs on the coin holder considering every design rules considered in the industry. THEORY: Class-B surface contains all the engineer data required for the model to be completed. This data involves designing of various features. Some of the major features of the B-side…

OBJECTIVE:                The main purpose of the challenge was to create the Class-B surface, Class-C surface with the given Class-A surface and performing the draft analysis by creating the tooling axis of the plastic component switch bezel by taking the thickness of 2.5mm of the…

OBJECTIVE : To design coin holder as per automotive OEM Standard. Create B Class and C Class and tooling axis. Convert close lose the surface into the solid body and provide the thickness of 2.5mm. Performing draft analysis to verify the creation of the Tooling axis and C Class surface. SOFTWARE:  CATIA V5 (Generative…

OBJECTIVE:                           The main purpose of the challenge was to create the Class-B surface, Class-C surface with the given Class-A surface and performing the draft analysis by creating the tooling axis of the plastic component switch bezel…

OBJECTIVE             Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Detailed…

AIM            Create the tooling axis for the Fan cover model meeting the requirements of the draft angle and perform the Draft analysis on the model. APPROACH FOR DRAFT ANALYSIS            Ensure that the given class A model is properly joined and has no discontuinity…