Week 10- Assembly Workbench

BACK DOOR Aim:  To design a Backdoor of the car on sheet metal using the appropriate design and provided skin data by considering design rules. Objective:  To design the backdoor with design methodologies and and provide the emboses,reinforcements in the inner panel and side relief in outer panel to increase…

AIM :           To Create the car's roof using the given class A surface with the Given Guidelines of OEM. ROOF : An automobile roof is considered an integral part of BIW (body in white) design. A car roof is responsible for protecting the passenger from rain, wind, sunlight, accidents, etc. It also offers aerodynamic…

FENDER DESIGN  FENDERS:                 The fenders are panels that extend from the front bumper to the vehicle’s doors. it prevents sand, mud, rocks, and liquids from being thrown into the air by the rotating tire. Moreover, automotive fenders play a major role in the…

FENDERS:                 The fenders are panels that extend from the front bumper to the vehicle’s doors. it prevents sand, mud, rocks, and liquids from being thrown into the air by the rotating tire .Moreover, automotive fenders play a major role in the safety of the vehicle…

A detailed report of Switch Bezel Design AIM:  Create the Switch Bezel component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the draft angle requirements and performing the Draft analysis on the model at the end. TOOLING AXIS: There…

REPORT FOR SECTION MODULUS CALCULATION AND OPTIMIZATION Aim To find the section modulus of the hood and optimization to improve the overall section modulus. there is  Section modulus:- The section modulus (S) is the geometric property of the cross-section used for designing beams and flexural members. It does not…

OBJECTIVE  In this Project, I am going to Design the Hood of the Car and The Main Purpose to Improve Strength of Body, Reduce the Material weight of Body and Improve Mailage of Car and Saftey Purpose Using Different Types of Sheet Metal Operation and Design Shape on Front  Hood Car Body. A car hood is…

INTRODUCTION : A Car Body is made up of several Metals such as Iron, Steel, Aluminum, Copper, etc. Rusting is the common term for the corrosion of iron and its alloys. Corrosion is the reaction of Iron and Oxygen, as may present in Water or Air Moisture. Any Iron material when exposed to both oxygen and water is bound…

AUTOMOTIVE BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance Automotive Benchmarking is the process of analyzing the choices of similar products based on the selection factor and deducing it to a conclusion. CASE Mr. D.S. Pughazhyendhii is a married man who…

AIM: To design and develop vehicle interior door trim using Catia V5 with given class A surface and Master section. Also, create the Side Attachment features as per design rules. OBJECTIVE: To create thickened part using the master section for reference To create the mounting features as per design guidelines in the industry…

  THE 3-2-1 PRINCIPLE: Locating a part to be machined involves mainly three steps: supporting, positioning and clamping. Two main intentions when placing a job on a jig/fixture are: Precisely positioning the part at the desired coordinates. Curbing all six degrees of movement so that the part cannot budge. An extensively…

AIM: The main objective of this challenge is to create the A-pillar Design component through the above-given Class-A surface A and Master section, by giving the Tooling axis and 'Draft analysis' to the class-A surface. TOOLING AXIS:  There are 3 types of Tooling axis can create based on giving model,…

OBJECTIVE: The main objective of this challenge is to create the Door Trim component through the above-given Class-A surface, by giving the Tooling axis and 'Draft analysis' to the class-A surface of the bumper. TOOLING AXIS: We should deeply observe and study the class A surface to create the 'Tooling Axis'…

AIM: To Create the door Trim Component from the given Class-A surface. To Create the Tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To perform the Draft analysis on the model.  To Create the B Side Feature in the component by following the design rules. DESCRIPTION:   1.…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model. TOOLING AXIS: There are three types of tooling axis : concerning…

AIM: To Create the Core and cavity blocks for the switch bezel component. DESCRIPTION:   1. CREATING TOOLING AXIS -                       The Tooling Direction is the direction that the mold pulls apart. The mold is built in two separate pieces. You have…

AIM:  Create the bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the draft angle requirements and performing the Draft analysis on the model at the end. TOOLING AXIS: There are three types of tooling axis : with respect…

AIM:  Create the coin holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the draft angle requirements and performing the Draft analysis on the model at the end. TOOLING AXIS: There are three types of tooling axis : with…

A detailed report of Base Bracket Design AIM:  Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the draft angle requirements and performing the Draft analysis on the model at the end. TOOLING AXIS: There…