Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash? Ans:- Aim:- Mix Design for M35 grade concrete with fly ash Step:-1 I. STIPULATIONS FOR PROPORTIONING OF M35 GRADE CONCRETE   A Grade Designation M35   B Type of Cement OPC 43  IS 8112 to conforming…

Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from the members…

Que :- Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where      required you need to use the circle tool.Please read the drawings and find out the missing dimensions before working on the sketches.   Ans:- …

AIM:  To Creating a Floor plan, Footing detail and Isometric view using AutoCAD. INTRODUCTION: The main objective of this assignment is to get in touch with various tools in AutoCAD like the rectangle, polylines, modifications tools like copy, move, offset and modes like snap mode and ortho mode. These tools will…

AIM: To draw the geometries using Chamfer, fillet tool in Autocad. Commands used: Line, circle, chamfer, fillet, mirror, trim, move, rotate, annotate. Procedure: 1.Open new file and set decimal and precision to 0.00. 2.Command line: From random point draw 3.00 m line and @2.12<45, @2.83<135 then 2.00m line…

1. Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors. AIM: To draw the given residential plan with the…

1. Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left AIM: To Create a column schedule as shown in the figure: INTRODUCTION:  Column C1 is…

1. Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching, you need to provide the dimensions and text with the use of layers. Use proper text styles and dimension methods to document it. Also, assume dimensions, wherever needed. Note: All dimensions are in mm. AIM: To Draw the elevation…

1. Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required. Aim:- To draw the floor plans and sections using the proper dimension…

Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East   c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan) AIM: Design…

Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule. Commands Used in this challenge:  Line Rectangle…

Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards. AIM:  To create kitchen layout and details by using AutoCAD with the help of given figure. INTRODUCTION:…

CHALLENGE:-1 1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. AIM: To create a 3D Furniture element as given in the figure and need to assume dimensions which are missing in the drawing. INTRODUCTION:- The three dimensional furniture element was drawn in the autocad using the different…

1. Create a 3D Isometric View of the building with plan and elevation given. AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One…

Create a 3 dimensional model of the residential building with a rendered view.   AIM:- To create a 3 dimensional model of the residential building with a rendered view .  INTRODUCTION:- 3D computer-generated images of proposed building projects and other types of constructions are widely used by architects…

1) From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. AIM :- To create a new project from the file menu and need to name the project appropriately. INTRODUCTION:- For creating a project, select a template from the Projects list or the New Project dialog…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION:- The creation of Ceilings within Revit is a very similar…

1) Select the type of structure you want to build from one of the three below:         a. Multi-Unit Residential Apartment         b. Office Buildings         c. School Ans:- My project is to built the Multi-unit residential apartments from the given three…

1) Using Dynamo create a set of sinusodial points and create a curve and create a surface out of the curve. AIM:- To create a set of sinusodial points, create a curve and To create a surface out of the curve. INTRODUCTION:- Dynamo is a visual programming tool that works with Revit. Dynamo extends the power of Revit by…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM:- To export the Revit architecture and structure model to Navisworks Cache file following the export settings.…

  Identification of Cracks   1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate. a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus…

Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) The nature of loading governs the kind of analysis to be performed on the structure. The loads are divided into two basic categories Static Loads are the loads, the variation of load with respective time is very slowly…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and its associated mode shape: The…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Answer:- Symmetry:- It is observed that the distribution of mass,stiffness…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm  Columns : 800 × 800 mm  Slab : 150…

Que:-    AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR. INTRODUCTION: The structural configuration of the building plays a major role in determining the overall response…

QUESTION:- Detail design of beams in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A    …

Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns,…

ANSWER:- Aim:- To provide,             The cross sectional steel arrangement of the shear wall from its base up to terrace, in compliance with provisions of IS 13920 – 2016.              The drawings of the reinforcement details of the shear wall…

The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load, also…

    AIM:- 1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. INTRODUCTION:- CSI SAFE (Slab Analysis by the Finite Element Method) is the best tool for designing concrete slabs and foundations. SAFE provide easiness…

Project 2_Design & Analysis of a Hostel building at Guwahati, Assam INTRODUCTION:-  The procedure and anaylsis and design of given building will depend on the type of building, its complexity, the number of stories etc. First architectural drawings of the building are studied, structurl systems is finalised sizes of structural…

1. 1. Write the steps involved to upload a .std file through web mail?    2. Name the different materials that can be designed using STAAD Pro.    3. Is it possible to capture images in STAAD Pro? If yes how?    4. Name the three ways by which you can create a model.    5. Write…

Ans

Aim:- To provide the primary load cases fro design, defination for one way slab, unit weight of structural steel and soil, name of few sections, define primary beam. 1.     1. State the primary load cases to be considered for design. The primary load cases are Dead load (IS 875:part 1) Live load…