question no:1 Ans: when the switch is close battry connect with solenide coil and currunt pass and EMF generate  and ,etal rod will attract near ball and collide with the ball and creat sound .

Aim:-Implement control logic of a ''Washing machine" using as per given  sequence  Objective:- 1.Understand and implement logic  control of a state Machine  using  state flow 2.If the power supply available ,the system gets activated 3.If the water supply is not  avilable , stop the process…

Aim:- To prepare a technicale report of simultion of BAJA All Terrain(ATV) under diffrent condition. objective:-   carry out a system level simulation an of all terrain vehicle prepare a technicale report explaining the model properties & comments on the results. All terrain vehicle: An all- terrain vehicle…

Que no.1 Create a detailed MATLAB model of an electric rickshaw (three wheel passenger vehicle) as per details below:  Rear wheels driven by PM brushed type motor Assume efficiency points of motor controller and motor Make an excel sheet of all input and assumed data  Results: For any three standard driving cycles…

AIM:  Create a MATLAB model of electric car which uses lithium ion battery and suitable motor. Choose suitable blocks from Simscape or Powertrain block set. Implement the vehicle speed control using PI controller and generate brake and accelerator commands. Avoid using readymade driver block for speed control.  …

1.   For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations.  Ans: Mass consider for the EVcargo is 500KG. One FTP cycle equal 17.77km so that if cover more than 45km then we have to increse 3 times.…

What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?  Ans:       Mapped model  1) In mapped model data points are pre-assigned in lookup table which would be configured with the operational parts and the…

1.  Which types of power converter circuits are employed in electric and hybrid electric vehicle?   Hybrid Electric Vehicles: A hybrid electric vehicle (HEV) is a type of hybrid vehicles that combines a conventional internal combustion engine (ICE) system with an electric propulsion system. The presence…

Que :1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’. Answer: 'Speed control of a DC motor using BJT H-bridge. H-bridge:In general an H-bridge is a rather simple circuit,containing four switching element,with the load at the center, in an H-like configuration.     The basic operation…

Que:1  For a defined driving cycle, calculate the energy required for braking. Ans: Braking: The function of the braking system is to retard the speed of the moving vehicle or bring it to rest in the shortest possible distance whenever required. The vehicle can be held on an inclined surface against the pull of gravity…

Que: 1:  Search and list out the total weight of various types of aircrafts.  The aircraft gross weight (also known as the all-up weight and abbreviated AUW) is the total aircraft weight at any moment during the flight or ground operation.  An aircraft's gross weight will decrease…

AIM: Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:  System level configurations Model parameters Results Conclusion   Create a MATLAB model of electric car which uses…

Que:1   Overview of the Project: (5 to 6 lines) In this project,  interfaces for mathematical Set Theory are implemented using C programming language. User can give the input like two list of data and this program will give  the output as the union and intersection of these two lists 1.here we taken by the…

Project 2 - Implement the Code for controlling the retraction and extension of Airplane’s landing gear   Ans: Overview of the Project: (5 to 6 lines) In this project, controlling the retraction and extension of Airplane’s landing gear can be implemented using Finite State Machine (FSM). FSM is the most efficient algorithm…

Write a Test plan to test features of a new mobile phone (Blackbox test) that needs to be implemented based on the following requirements.(The product is still under development stage and is yet to be UA (User Acceptance ) tested .Every other thing to be included in the test plan can be hypothetical. TEST PLAN: if(owner…

Perform Static Code Review Analysis for “C:\**\LDRA_workarea\Examples\C_Testbed_examples\Testrain\Testrain.c” Generate Code review report and upload them. Ans:  File to be attached.       Perform Integration testing by including all the .C files available in the folder location C:\**\LDRA_workarea\Examples\Toolsuite\Cashregister_6.0\…

PROJECT :1 Overview of the Project:  In this project implementing the Code for “Interfacing a 16*2 LCD with two Arduino’s (one for Master and one for Slave) using Inter-Integrated Circuit (I2C) communication protocol” by sending the message to LCD using I2C communication protocol and display the…

Overview of the Project:  In this project, the implementation of code for “Measuring distance of an object using ultrasonic distance sensor (HC-SR04) Goals: Measuring the distance of an object using Ultrasonic Distance Sensor (HC-SR04) Usage of Input Capture Mode COMPONENTS REQUIRED: BREADBOARD ARDUNIO OSCILLOSCOPE…

Mini Project - Vehicle Direction Determination General Overview: Identifying the direction of the vehicle is one of the important & diverse features in Autonomous driving & Advanced Driver Assistance Features. This particular sub-feature of identifying the direction of vehicle is basically identifying the direction…

  Main Project – Adaptive Cruise Control (ACC) General Overview: Adaptive Cruise Control Feature for passenger cars allows the host vehicle to adapt to the speed in line with the flow of traffic. Driving in heavy traffic or keeping a safe distance to the preceding vehicle calls for a high level of concentration.…

PROJECT :1 Overview of the Project:  In this project implementing the Code for “Interfacing a 16*2 LCD with two Arduino’s (one for Master and one for Slave) using Inter-Integrated Circuit (I2C) communication protocol” by sending the message to LCD using I2C communication protocol and display the message on LCD screen.…

Overview of the Project:  In this project, the implementation of code for “Measuring distance of an object using ultrasonic distance sensor (HC-SR04) Goals: Measuring the distance of an object using Ultrasonic Distance Sensor (HC-SR04) Usage of Input Capture Mode COMPONENTS REQUIRED: BREADBOARD ARDUNIO OSCILLOSCOPE FUNCTION…

Aim Of The Project:  Implementation of the Traffic Jam Assistant algorithm which would predominantly feature in the IPC algorithm. Objective of the Project: The model must be developed in MATLAB Simulink as per MBD guidelines. Simulink Data Dictionary must be created for the model & must be linked to the…

Overview of the Project:  In this project, the implementation of code for “Measuring distance of an object using ultrasonic distance sensor (HC-SR04) Goals: Measuring the distance of an object using Ultrasonic Distance Sensor (HC-SR04) Usage of Input Capture Mode COMPONENTS REQUIRED: BREADBOARD ARDUNIO OSCILLOSCOPE FUNCTION…

   Project 2-Highway Assistant-Lane Changing Assistant                                                                          …