AIM: We aim to make a 'two arm robot' with the help of programming (MATLAB) Formula: LINSPACE:Generate linearly spaced vectorLINSPACE(x1,x2,n)FOR LOOP:The formula 'FOR LOOP' is used.in which 'FOR LOOP' to repeat spacified number of timeswhich is,for i = value; statementsendPLOT COMMAND:and that the formula 'plot'…

AIM:- We aim to program an (ODE solution) for the motion of the pendulum  FORMULA:- t_span = linspace(0,20,500); [t,results] = ode45(@(t,theta) pdm_func(t,theta,b,g,l,m),t_span,theta_0); plot(x1,y1,'markersize',50,'marker','.','color','k'); dtheta2_dt = -(b/m)*theta2-(g/l)*sin(theta1);  EXPLANE THE CODE:- 1st…

DRAWING-        

 BEZEL-      

DRAWING- Tooling axis: The direction in which the mold or core and cavity opens is the tooling axis. Connectivity of Class-A surface checking the connectivity of the surface, this can be done by creating boundaries or by simply using the join option such that any openings can be easily visualized   DEFINE:- First…

DRAWING- ALL VIEWS-   CORE AND CAVITY-            

  DRAWING- Tooling axis:- Connectivity of Class-A surface checking the connectivity of the surface, this can be done by creating boundaries or by simply using the join option such that any openings can be easily visualized. Draft Analysis :- create first tooling axis and then do the draft analysis. First change material…

1. PART DRAWING- 2. PART DRAWING- 3. PART DRAWING- 4. PART DRAWING- 5. PART DRAWING- 6. ASSEMBLY DRAWING-   REPORT- Create all part in part design and then go to assembly design and click the exiting componant select the all part and open. we have saprate all part with the help of manipulation First fix command used…

PLASTIC COMPONANT-         HEAT STAKES- 4 WAY LOCATORS- 2 WAY LOCATORS-    

Answer's:-   Report:- The number of commuters is five including a child and hence the vehicle should be spaciously. He uses his car for daily office commute and a monthly one trip to his native .This would give a total estimate of aproximatly 2500km/month. The budget is from 8-10 Lakhs. He is fond of big cars. Based…

Answer:- Under body Coating : Underbody caoting is a thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin.   Purpose : Underbody coating provides long term protection from…

AIM: To the Design car hood outer and inner panel and these reinforcements. Design the outer panel with the Hem Design the inner panel  Design all the necessary reinforcements Mirror and position the Hinge & Striker Provide Mastic Data  Emboss Define Provide the Detailed Report   Data to be used: Hood…

Answer:-                                                     SECTION MODULUS OF AN HOOD Section modulus is a direct measure of strength of any  sectional area of an object about an reference…

FENDER DESIGN OBJECTIVE : The main objective of this project is to design a fender using Catia v5. INTRODUCTION : Design of any product starts from an requirement . The design engineer sketches the product based on the the requirement . Then the 2D sketch  with the proper dimensions is converted into the 3D model…

Question: For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs.…

Answer:- Wheel Arch gap - Calculations   Aim:-      To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure…

Answer:- Aim:  From the given CLASS A surface, create a Backdoor Design using Catia v5 software. Provide the Reinforcements (Hinge axis, Gas stay, Wipper motor, Stricker) and Emboss defination  (Design cosidretation)   OBJECTIVE:- To create the following components of the backdoor panel from the given styling surface.…

Answer: Objective:- The objective of this project is to design the assembly of the Butterfly valve and apply the GD&T concepts to the various parts of the Butterfly Valve.   Software used:- NX cad   INTRODUCTION:- A butterfly valve is from a family of valves called quarter-turn valves. In operation, the…

                                                                                                              MODELING OF AMERICAN CHOPPER IN SOLIDWORKS   Objectives- The main objectives of this project are: To make the individual parts of Chopper using solidworks. To assembled all the individual parts into chopper To…

Answer:- Title:- Radar Mast & Final Assembly of Yacht Objective:- Design of Radar Mast  Major Feature:- Extruded boss/base, Revolved boss/base, Sweep, Combine, Projective curve, Shell, Dome, Fillet and Cut sweep i.e. Radar Mast :- First one, we have create a new file and go to insert then part …

Answer:- Design, Assembly and Rendering of Circular Loom Machine using SolidWorks and SolidWorks Visualize Objective:- Design the parts of the Circular Loom Machine Assembled the parts in solidworks assembly. Rendering image using photoview 360 and SolidWorks Visualize.   Link of Parts & Assembles -  https://drive.google.com/drive/folders/1HLHXGXXHmPtvlKT5RnSF5R76lDleM3Va?usp=drive_link…