refer attachment..

Refer to the attachment.

refer the attachment

report & model is attached herewith..

refer the attachment

refer attachment...

refer to the attachment for the report & model.

Please refer to the attachment of the model & report Application: 1. Synchronous modeling 2. Part optimization 3. weight reduction proposals 4. New variant introduction 5.concept generation for innovative ideas  

refer to the attachment for the report but the model unable to attach

please refer to attachment for report & model..

 Please refer the attachment for model & report..

please find the attachment for report & model....

Objective: Create a Tetra mesh for Housing component with the following quality criteria. Tetra Mesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15 Housing Model   For the given model, Create a 3D Tetra mesh with the following quality…

Objective: To perform & Deploy the connection on the components as per the challenge requirement. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L)  Left_Rail_2 & Front_truss_1:- Quad elements  Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 2 Layers and 5…

Objective: Perform meshing on the following side door components with the given criteria and assign material, proper thickness.   Procedure: The meshing is done by following steps 1. Import side_door_panel.hm in to Hypermesh  2. CAD Geometry clean up and topology 3. Mid-surface extraction 4. Defeaturing…

Objective: Perform meshing on the following Rear Wheel Holder components with the given criteria and assign material, proper thickness.   Procedure: The meshing is done by following steps 1. Import Rear Wheel Holder.hm in to Hypermesh  2. CAD Geometry clean up and topology 3. Mid-surface extraction 4. Defeaturing…

Objective:- Write a detailed report on unit conversion with calculations and there units. 1) Convert Kg cm ms MASS 1kg = 1000gms. LENGTH 1m = 100cm. TIME 1s = 1000ms FORCE = ma=mass * Acceleration unit = kg·m/s2   STRESS = Force/Unit area unit = N/m^2. Value of the following measurements…

Aim: To study about implicit and explicit method to solve engineering problems. Objective: To demonstrated in the PDF, F(u) = u3+9u2+4u use this equation and solve using both Explicit and Implicit Methods with tolerance of 10-2. Explicit: As opposed to Implicit methods, explicit method is a function of time.…

                                                                    Drop Test of Cell phone on plate…

AIM: To simulate a crash test simulation of crash box impacting a rigid wall in LS-Dyna. OBJECTIVES: To create a rigid wall in LS-Dyna Apply initial velocity of 50 kmph to the crash box. Run the simulation and compare results of crash box having thickness 1.2 mm and 1.5 mm respectively. The unit system followed is gm-mm-ms…

AIM: To create a block of 10mm*10mm*10mm dimension with 10 elements each direction and use the material card attached.(ogden_material.k). To use appropriate boundary conditions to simulate uniaxial tensile behaviour of the model. compare the results of the simulation with ELFORM=1,2,-1,-2 by plotting…

  Report is attached. Related files are attached in google drive & link is shared in report.   Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue & i had faced the issue in eralier challenge as well.}    

Report is attached.   Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue & i had faced the issue in earlier challenge as well.}

Report is attached.   Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue & i had faced the issue in eralier challenge as well.}

Report is attached.    Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue & i had faced the issue in eralier challenge as well.}

Report is attached. Related files are attached in google drive & link is shared in report.   https://drive.google.com/file/d/1XOnK8PU4B1LUufmTjoJ6tExkNQRxy2DY/view?usp=drive_link   Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue &…

Report is attached.         Info: { The report is not being processed while it is being written in the allotted space. Kindly resolve the issue & i had faced the issue in earlier challenge as well.}