Abstract: Butterfly Valve is used to regulate and control, Throttle the flow. They are featured by fast operation and low pressure drop. Objective: To model a Butterfly Valve using Ansys Design Moduler software. Procedure: A Butterfly Valve generally consist of three main units a main central units, a top head and…

Abstract: whenever a uniform plate without any defect is subjected to axial loading the stress distribution along any cross section is uniform however when any hole is present in the plate the stress distribution at the cross section of the plate near the hole more as compare to the other area. The stress calculated…

Grip Dependency: In a finite analysis method infinite degree of freedom of any component is converted into finite degree of freedom by the concept of meshing. In Meshing the overall component is converted into the combination of elements and nodes. All the results are calculated at the nodes and then interpolated on the…

Objective: To perform a static structural analysis on a railwheel and track setup using two different bearing loads (100000N & 500000N) and compare the results for Total deformation, Euivalent stressand Fatigue life and also to Implement a User defined result and calculate the Total Deformation from this result and…

Objective:To perform static structural analysis of Spur gear using three different material (Cast steel, Cast Bronze and Cast iron) and  to find out Equivalent stress, Total deformation and Stress intensity. Stress Intensity: Stess Intensity factor (K) is used to define the crack intensity factor at the crack tip. It depend…

Objective: To perform a sheet metal bending analysis using three different materials ( Al Alloy 1199, Cu Alloy NL, Mg Alloy NL) and compare their results for Equivalent Stress, Elastic strain and total deformation in Y direction and also to perform a grid dependency test using Al Alloy NL as a material for the sheet metal.…

Objective: To do the analysis of weld joints using three different materials( Al Alloy, Stainless steel and Bronze) and compare their result for the Directional Deformation and equivalent strain experienced by the setup and also to Identify the weld joint that experiences the highest equivalent stress in each case and…

Objective: To simulate the rolling operation on a workpiece made of copper and then to evaluate Equivalent stress for the whole setup,Equivalent Plastic strain for the workpiece,Directional Deformation in the Z axis for the workpiece and also to prove that the workpiece has displaced by 90mm. Set up & procedure:…

Objective: To perform the analysis to simulate a sphere pressing on a plate by 4mm downward and to capture the plastic deformation on the plate. Set up & procedure: From the Engineering data source we have selected Structural steel and Structural steel NL for analysing the above simulation. The material properties…

Objective: To perform the bending test of iphone and to compare the results with another case where the bottom hand has been displayed from their defined position to the given position X= 22.5mm & Z= 10mm and obtain the results for the simulation and also to define the S-N curve for the Aluminium Alloy material as per…

Objective: To perform an analysis to simulate the bending of a wire in ANSYS,for which we will have to use Copper Alloy (Non Linear), Aluminium Alloy (Non Linear) and Magnesium Alloy ( Non Linear) for the wire alone. We need to find out the Equivalent stress and Equivalent strain on the wire alone and Compare out the results.…

Objective: To perform a transient analysis on a piston and cam mechanism model that has been provided to us and we need to run the analysis with Frictionless contact, Frictional with 0.1 and 0.2 as the frictional contact for a total of 3 cases and we have to find out the Equivalent Stress, Directional Deformation and Equivalent…

Objective: To perform a transient structural analysis on a double universal joint with a spring using three different materials: Structural Steel, Stainless Steel and Titanium alloy and to obtain the Equivalent stress and total deformation for all the three cases and compare them. Case setup & Procedure: From the engineering…

Objective: To perform a transient structural analysis on a worm gear assembly and we need to cut the gear by half so as to bring the model within  acedemics limits. For the challenge, you have to rotate the worm so as to get to almost end of the half cut and get results for Equivalent stress, Equivalent elastic strain…

Objective: To perform the tension and torsion test on the specimen provided, In case for the tension test we have to displace one end of the specimen to 18mm while keeping the other fixed whereas For the torsion test, we will have to displace one end of the specimen to an angle of 1200 degree and finally we need to Find…

Objective: To perform an explicit dynamics simulation for Machining with planer and to find out the Equivalent Stress, Total Deformation and also insert a User defined result to calculate the temperature of the body. We need to perform this for 2 cases. One will be with a cutting velocity of 20000mm/s and the other will…

OBJECTIVE: To simulate a bullet penetrating into a bucket by using 3 different non linear materials for the bucket and analyse their behaviour for the same velocity of bullet. Case setup: From the engineering data source we have selected three non linear material i.e Aluminium alloy NL, Stainless Steel NL, Magnesium Alloy…

Objective: To perform a parametric study using 3 different values of thickness for the car body and to Analyse the total deformation and Equivalent stresses acting on the model. Case Setup: From the engineering data source we have selected structural steel and stainless steel NL for carrying out our analysis.          …