DESIGN AND RENDERING  OF AMERICAN CHOPPER BIKE OBJECTIVES             TO CREATE MODELLING AND PHOTOREALISTIC RENDERING OF AMERICAN CHOPPER BY…

1. RADAR MAST 2. YACHT ASSEMBLY 0                                     Modeling and Assembly of Sunseeker predator yatch objective:                      The main aim is to produce…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the draft angle requirements and performing the draft analysis on the model at the end. INTRODUCTION The Draft allows the part to easily eject from…

Switch Bezel Design: Objective : To design switch bezel as per automotive OEM Standard. Create B Class and C Class and tooling axis. Converting close surface into the solid inside part workbench and providing the thickness of 2.5mm. Performing draft analysis to verify the creation of the Tooling axis and C Class surface.…

  BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surfaceand the outermost surface.CLASS-B SURFACE: a surface below a certain thickness from…

 DESIGN OF COIN HOLDER AIM: To create the coin holder plastic component through the given Class A surface. To begin with, the tooling axis for the given Class-A surface should be created meeting the requirements of the draft angle and at the end perform the draft analysis on the model. Take the thickness of the…

AIM: to create the core and cavity for the switch bezel considering all design rules. TOOLING AXIS: IT IS THE AXIS IN WHICH THE DIRECTION CORE AND CAVITY OPEN. THIS IS THE VERY IMPORTANT FOR THE PRODUCTION OF PLASTIC COMPONENTS. MOST OF THE DEFECTS WILL BE DONE IMPROPER TOOLING AXIS CREATION BY THE PLASTI DESIGNER.…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

AIM: Create  A pillar Design with Master Section OBJECTIVE: Creation of proper tooling direction following the master section to create the part that meets the requirements Draft analysis check to make sure that the class A surface is meeting the draft required along the tooling direction Creation of Dog house,…

AIM Create the Dog House for the Door Trim considering the design rules mentioned in the video. Requirement Screenshots of the completed design in various orientations (Isometric, Front, Side, and Top View) A detailed report explaining the draft analysis and the tooling axis creation should be done.  An explanation…

  AIM-  Define given connectors & connector clip as Electrical Connectors and add they're necessary properties using the Electrical Part design workbench in CATIA V5 OBJECTIVE- The objective of this project is to first download the given files from TE.com, then define them as an electrical connector…

Q1. Download the following cad data & define it as Electrical support using the Electrical Part Design Workbench. Define all the necessary properties. Q2. Download the following Back shell cad data & define it as an Electrical back shell using the Electrical Part Design Workbench. Define all the necessary properties.…

AIM:- Route the following harness layout in the Electrical workbench. Make assumptions for harness bundle diameters. Use the following connectors as shown in the layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)  Download…

Q1. Route the following harness layout in the Electrical workbench. Assume harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add a snap of the result in the submission Add annotation to all connectors. Make assumptions for annotations like connect 1, 2, etc…

AIM- To prepare a flattened view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals on the…

 already i submitted this challenge but it not showing and also i got a markes but now it showing to attempt AIM-  Define given connectors & connector clip as Electrical Connectors and add their necessary properties using the Electrical Part design workbench in CATIA V5 OBJECTIVE- The objective…

 I ALREADY COMPLETED THIS CHALLENGE Q1. Download the following cad data & define it as Electrical support using the Electrical Part Design Workbench. Define all the necessary properties. Q2. Download the following Back shell cad data & define it as an Electrical back shell using the Electrical Part Design Workbench. Define…

I ALREADY COMPLETED THIS CHALLENGE  AIM:- Route the following harness layout in the Electrical workbench. Make assumptions for harness bundle diameters. Use the following connectors as shown in the layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end…