Introduction:  In this project, we learnt about designing an American Chopper using Solidworks. learn about each command and create each part in Solidworks. After designing the parts and doing the assembly after that rendering the model using Photo view 360 and Solidworks VisualizeWhile rendering we get to know about…

OBJECTIVE : To model every part of the Sunseeker in solidworks   INTRODUCTION : This project is about modeling parts of the Sunseeker and assembling it using Solidworks  PROPELLER : Propeller is used to push the water and to navigate across the ocean. Commands used to model the propeller are Spline, Circle, Line,…

ASTON MARTIN OBJECTIVE: To model parts of Aston Martin One-77 Modelling, assembling and rendering of Aston martin car model using surface modelling and solid modelling techniques in solid works. INTRODUCTION: In this project we learn how model the parts of the Aston Martin One-77 Flow Chart: TOOLS USED:  …

Objective: To model parts of Boeing 747  in SolidWorks and assembl them and  then rendered for photo realistic view using SolidWorks Visualize. Introduction: Boeing 747-8 is a wide body aircraft being the largest variant of the 747 is modelled using the Solidworks. The below data shows the…

Result: Flow through Cylinder Explation: Here in this we will Calculate the pressure and velocity at the value and Re also Precedure: first draw sketch of the cylinder and extrude  the apply the boundary conditions  the apply the cut plots and then do the animation Result: At V=12,re=32219 pressure at v=14,re=37589…

Objective: Model the flow over a NACA0017 airfoil For the angle of attacks 0,2,4,6,8,10 compare the lift and drag forces Procedure: Importing the co-ordinates of the airfoli (Insert -> Curve -> Curve through XYZ points ->bowse the file ->open-> ok)     Converting into sketch (Front plane ->…

OBJECTIVE: To a Perform a Grid dependency test for a particular valve lift Perform a parametric study to determine the effect on the mass flow rate with different valve lifts Plot velocity cutplot for different valve lifts. PROCEDURE: Draw the Circle    Do the Boss Extrude    Draw the Intake Port         …

OBJECTIVE Run the parametric study of a centrifugal pump for different velocity at outlet Plot the pressure ratio vs mass flow rate THEORY: A centrifugal pump is a mechanical device designed to move a fluid by means of the transfer of rotational energy from one or more driven rotors, called impellers. Fluid enters the…

AIM: To performance of three types of beams under bending load. PROCEDURE: Draw the rectangle as given dimension and another 2 shapes          Now do the Boss Exrude upto 400      Now apply the new simulation study static and apply the material to all three types beams…

Aim: To apply the static process on T-section. Note: Units are in mm Procedure: Select the front plane draw the t section and give the required dimensions. Now the Boss Extrude Now Boss extrude 80mm Now do the simulation command Create the new study and perform the static process Now apply the alloy steel(ss) to created…

Aim: To perform the geneva mechanism on created the 3D model to perform the motion study at different speed. Introduction: Geneva mechanism, also called Geneva Stop, one of the most commonly used devices for producing intermittent rotary motion, characterized by alternate periods of motion and rest with no reversal…

Aim: To design the  planetary gear and to do the the motion analysis on the gear procedure: Here in the we will design the Planetry gear and do motion analysis on it  it will design according to the given values

Aim: To do MBD Simulation on a Piston Assembly parts of piston assembly: piston connecting rod end cap wrist pin crank    procedure: Design of piston assembly  as per given dimensions   Design of piston: Design of connecting rod: Design of end cap: Design of wrist pin: Design of crank: Assembly:…

Aim: To do the MBD Simulation on IC Engine Valve Train. Parts of IC engine: cam engine valve pushrod rocker's arm valve engine valve mount After analysis the results of plots:        

Aim: To do the motion analysis on the bevel pinion & gear. Software used: Solidworks software 2022. Note: Units in mm Procedure: First, we will get the gear from the design library of bevel pinion & gear As per the required data, we will set up the gear teeth and dimensions  In this motion study, we will give…

Aim: To Design the Four-cylinder Engine. Introduction: In this project, we learnt about designing a Four-cylinder engine using Solidworks. learn about each command and create each part in Solidworks. After designing the pieces and doing the assembly after that rendering the model using Photo view 360 and Solidworks VisualizeWhile…