Objective: To plot graph showing the effect of variation in Velocity of Cyclist and Coefficient of Drag on the Drag Force Problem Statement:  Given the factors involved in the computation of the Drag Force, which are:      Velocity of the Cyclist (v)                                                …

Objective: To write a program to simulate the forward kinematics of a 2R Robotic Arm Problem Statement:  A robotic arm is a type of mechanical arm, usually programmable. The arm may be the sum total of the mechanism or may be part of a more complex robot. The links of such a manipulator are connected by joints allowing…

Objective: To solve an Otto cycle, create a PV diagram and compute the thermal efficiency of the engine.  Problem Statement:  The Otto cycle is a set of processes used by spark-ignition internal combustion engines both 2-stroke or 4-stroke cycles. These engines ingest a mixture of fuel and air, compress it, cause…

Objective: To write a program that solves the ODE that represents the equation of motion of a simple pendulum with damping. And also, to simulate the transient behavior of a simple pendulum and to create an animation of its motion. `(d^2theta)/dt^2 + b/m *(d theta)/dt+g/L *sin theta=0` Problem Statement: In Engineering,…

Objective: Writing a python script to solve for the minimum value of pressure using the Newton Raphson method.      where p denotes the cushion pressure, h the thickness of the ice field, r the size of the air cushion, σ the tensile strength of the ice, and β is related to the width of the ice…

What do popt and pcov mean? popt: It gives an array with the optimal values for the parameters so that the sum of the squared residuals of data is minimized. pcov: It is a 2d array with the estimated covariance of the parameters in popt. It can be used to calculate the standard deviation errors of popt. What does np.array(temperature)…

Objective: To write a program to analyze various data plots for a converge engine output data file and calculate the required parameters. Problem Statement: To write a script that does the following: Data Extraction The data is to be stored a 2D array which contains for all parameters individually  Data visualizer…

Objective: To perform the external pipe flow simulation. Run a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number by a factor of 20%, 40%, and 100% then run the transient flow simulation. Introduction to the underlying Concept and Software used: Engineering Fluid Dynamics (EFD)…

Objective:Model the flow over a NACA0017 airfoil for the angle of attacks 02,4,6,8,10 compare the lift and drag forces. Theory:Airfoil shape like that of an airplane wing, tail, or propeller blade produces lift and drag when moved through the air. An airfoil produces a lif5in force that acts normally to the airstream and…

Objective: Create a 3D model of a flow bench. Run a parametric study on different valve lift. Run flow analysis and obtaining a plot graph between lift and mass flow rate Introduction: A flow bench is a device used for testing the internal aerodynamic qualities of an engine component. It is mainly used for testing the…

Introduction:A Centrifugal Pump is a hydraulic machine used to raise the liquids from a lower to a higher level by creating a required pressure by means of centrifugal action. These are the machines that increase the pressure energy of a fluid. These may either lift the fluid or just boost the pressure in a pipeline. Working…

Objective: To write a program that solves the ODE that represents the equation of a motion of a simple pendulum with damping. And also, to simulate the transient behavior of a simple pendulum and to create an animation of its motion. Problem Statement: In Engineering, ODE is used to describe the transient behaviour of…

Objective: To perform frequency analysis on the rotating shaft and to determine the made shapes and resonant frequencies of the model. Introduction: Frequency analysis is carried out to determine the natural frequencies of a part. Frequency analysis in SOLIDWORKS Simulation allows us to efficiently investigate the resonant…

AIM: Design the Internal Geneva Mechanism and perform the Motion analysis of it for different cases.   OBJECTIVE: Create 3D models for driver and driven wheels. Perform motion analysis by rotating the driver wheel at 10 rpm for 1st study and at 20rpm for another case. Obtain the results for Contact Force (between…