clear all close all clc b = 0.05; %DAMPING COEFFICIENT g = 9.81; %gravitational force l =1; %length of pendulum m = 1; %mass %initial conditions as theta 0 and 5 theta_0 =[0;3]; %time points here 100 values are taken betweem 0 to 20 t_span = linspace(0,20,500); %solve ode and ode function %ode45 id inbuilt solver working…

AIM : to find maxima of the function and get familiar with GENETIC ALGORITHM(ga) clear all close all clc %defining our search space where here 0 to 0.6 is divided in 150 %parts/numbers. x = linspace(0,0.6,150); y = linspace(0,0.6,150); %this is provided so that iteration or loop is executed for 50 times numcases = 50 ;…

AIM : 1)To get familiar with file parsing 2) Read the NASA thermo file 3) Extract the imformation needed to plot various graphs of different species with temperature. 4) Find molecular mass of each specie. close all clear all clc %opening the file f1 = fopen('THERMO.dat','r'); f2 = fopen('Molecular_mass.txt','w'); %as…

AIM : 1) To Simulink model of Doorbell using solenoid block.          2) To Use a thermistor to sense the temperature of a heater & turn on or turn off the fan as per conditions. SOL1:   1) To provide signal source pulse generator is used and as we have to close…

SOL1: 1)Two constant block are provided which work as switche for power supply and second as to know conditions of water is supplied or not. 2)In side chart 1st block takes input as water is supplied then 1 and is not then 0 same is for power supply. 3)If the power is not supplied 0 value is passed and according to conditions…

AIM : To study the simulation of  baja all terrain vehicle atv model. ATV : An all-terrain vehicle, also known as a light utility vehicle,  is a vehicle that travels on low-pressure tires, with a seat that is straddled by the operator, along with handlebars for steering control.  CVT model one:  The cvt model contains…

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% %% Skill-Lync -> Hybrid Drives Development % Project 1 - Conventional Vehicle Model % By - Ullekh Gambhira % Description: % The following file is to used with the Initialization file and Simulink % results for post-processing of the data. % The file…

TYPE FORMULA CATHODE MATERIAL ANODE MATERIAL SEPERATOR APLLICATION 1]  LCO LiCoO2  cobalt oxide Graphite carbon polyolefin Mobile phones, Tablets. 2] LMO LiMn2O4 Lithium manganese oxide Graphite carbon polyolefin Powertrains 3] NCA LiNiCoAlO2 Lithium Nickel Cobalt Aluminum Oxide Graphite carbon polyolefin Medical,Ev,Industrial…

Simulate the 3 test cases: CASE 1: From TEST SEQUENCE VARIANT block 1st case is seclected and model is run. when case  1 is seclected the folowing test sequence is seclected From BMS STATE REQUEST block: lets understand what this case actually is  the following image says about the same  1]For 1st 3000 sec…

The above cell has the specifications of nominal voltage (V)=3.3V Cell capacity (Ah) =2.5Ah Cell energy (E)=3.3*2.5=8.25kwh. We need to build 18kwh capacity battery pack. let us assume the vehicle motor has the voltage rating of 120V. Then the battery pack should have the same voltage rating to satisfy the load .ie, 120V.…

For better results I have used matlab example 20 series cell with fault and modified it. The thermal block are same as we used in previous challenges . 1]CONVECTIVE HEAT TRANSFER : this block is used cause in real life there are no such heaters used to heat the battery except working below 0DC , so the heating here takes…

DOING UNDEFINED checks: an example of part 2 is shown and same is done for all parts part2: before after Doing GEOMETRY checkup part1 before after BEFORE MESHING: part1: part2: part3: part4: • Cons and Hot points are altered according to fit the criteria, i.e., for hemming surface cons are joined to avoid failing…

AIM: To check for the geometrical errors and take the mid surface by suitable mid surfacing techniques ,for the given Plastic Bottle Cap model.  PROCEDURE: 1) Geometric Clean up. 2)Seting Target length to 1. 3)Uncuting and cuting the faces for better mesh elements. 4)Using curve middle for projection of complicated parts.…

Reason for late submission: Was out of station for couple of days  due to family issue

Aim: For the given Rear view mirror component 1]Mesh the Surfaces. 2]Mesh the Volumes defined in the model. SOLUTION: 1] Topo: 2] Geometry Checkup and fixing: 3] Repairing the elements failing for min/max values: a]By Reconstruct command: b] By using Transform->Move command:  ALL STEPS FOLLOWED: 1]Topo is done…

NOTE: Elements are failing near the hotes for min/max values are not resolved fully because reconstruction caused distortion in shape of holes . and support engineer suggested to focus on no off elements are present in volume mesh and collapse fails.

AIM:  1] To Development of MATLAB Simulink model for Vehicle Direction Detection. 2]Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems.   General Overview: Identifying the direction of the vehicle is one of the important & diverse…

AIM:  Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD creation, Configuration Parameter changes, Model Advisor check & Code Generation. In Configuration Parameters: enable “Support Floating Numbers”…

AIM: To Build Traffic Jam Assistant Feature on basis of requirenments Given. This model must be developed in MATLAB Simulink as per MBD guidelines. Code Generation Profile must be in Embedded Coder. Simulink Data Dictionary must be created for the model & must be linked to the model. Model Advisor Report is mandatory &…