WEEK 8 CHALLENGE 1

WEEK 8 CHALLENGE 2

                                         WEEK 8 CHALLENGE 3 COIN HOLDER

                        WEEK 8 CHALLENGE 6 CORE AND CAVITY

                 WEEK 8 CHALLENGE BUMPER

           Report: Checking continuity of given class A surface.First of all we have to check continuity of given class A surface to ensure class A surface is properly and to make tooling axis of the given component by using bisecting line method.

Checking continuity of given class A surface.First of all we have to check continuity of given class A surface to ensure class A surface is properly and to make tooling axis of the given component by using bisecting line method and next side tooling axis also want to create for draft analysis.

                            REPORT:Class A surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surface and the outermost surface. Class B surface below a certain thickness from the class-A surface…

                  Draft Analysis of A-Pillar design with Master section

BENCHMARKING-Benchmarking is a comparission of two products,process and servies which are already available in markets and new products.For example  compare processes in one retail store with those in another store in the same chain. REPORT: He uses his car for Daily office purpose and a monthly trip to his native…

UNDERBODY COATING         Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion rust underbody coating provides long term protection from corrosion to car's underbody.The underbody coating that is most commonly used on cars in India and…

HOOD DESIGN: AIM: To design the Hood or Bonet of the front driving car by using the master section and standard procedure which is used in the OEM Manufacturer's. GIVEN MASTER SECTION: HOOD: Hood is the component which is placed over the engine compartment. The design of the hood is not only to enhance the look of the…

Section Modulus calculation and optimization Aim:      To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive…

Aim:  To Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. Fender Arch:          Wheel arch is the semi circular part of the fender positioned above the wheel of the vehicle .The design of the wheel arch of the fender should…

FENDER DESIGN USING NX-CAD OBJECTIVE: The main objective of this project is to design a fender using a new age design software-NX-CAD INTRODUCTION:              Aluminum automotive components made using a hot blow forming process are reducing vehicle weight and increasing the fuel efficiency…

  ROOF DESIGN OBJECTIVE :        The objective of this project is to design car roof with  essential flanges and reinforcements  like ditch area , front roof rail , bow roofs, central roof rail and rear roof rail for the the given styling surface Perform a curvature study on the…

Design of Backdoor BACK-DOOR  DESIGN Objective:        Use the provided styling surface to come up with a back door design, use appropriate design methodologies and provide the necessary reinforcements and embosses. Software Used: NX CAD AIM: Use the provided styling surface to come up with a back…

Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:        Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch…

Wiring harness routing & packaging Rules Week 3 Challenge 1.Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 STEPS: Create two points one as entry and another as exit point. create planes…

Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA…

Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of…

Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM:  To flatten the wire harness assembly completed in week 4 assignment and place the flattened view on a drawing sheet.   OBJECTIVE: To flatten the wire harness assembly completed in week 4 assignment.  To orient the wire bundle as shown…

WIRING HARNESS DESIGN PROJECT 1 AIM: Design and develop the Wiring harness on Given V6 Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.   INTRODUCTION: A wire harness, also mmonly referred to as…

WIRING HARNESS ROUTING OF TAIL GATE Aim: Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while…

DESIGN OF BUTTERFLY VALVE & APPLYING GD&T TO THE PARTS & ASSEMBLY Objective The objective of this project is to model a butterfly valve and apply GD&T to the different parts and assembly of the butterfly valve.  Introduction A Butterfly valve is a quarter-turn rotational motion valve, that is used…

1.BIW:          The stage in automotive ndesign or manufacturing in which the car body sheet metel components are been assembled by welding and other joining process.In this stage in automobile manufacturing in which a car body's frame has been joined together, that is before painting and before…

1).The process of project execution activity   Project Execution         Project execution is carrying out the already designed plan. It involves putting into action all the activities that were set in the previous processes of the project cycle. All the activities are done according to the…

1. Design Methodology:      In this methodology we learn about three design processes, we're going to study how do we proceed while doing a design. And one of the things that we take care of structuring or design tree so we'll be learning how to structure the design tree, and how to name the particular…

Week 4:- Pin Unit Design Challenge Aim: To design two different types of Fixed Pin Unit and Retractable Pin Unit with different Pins, Riser, Blade, and Block design using Catia V5 OBJECTIVE: To design 2 different types of fixed pin units with different pins, risers, Blades &Blocks, and 2 Different types of retractable…

Week 5:- Rest Unit & Clamp Unit Design Challenge CLAMP UNIT AND REST UNIT DESIGN CHALLENGE: AIM: To design 3 Different types of Power Clamp Unit with Different Riser, Blade, and Clamp Arm and design 2 Different types of Rest Unit for the given Car Panel. INTRODUCTION A Clamp is a device that is used to hold the part…