ISRO Scientist/Engineer Mechanical 2025 paper: Part A, questions 21 to 40, solved

Questions 21 to 40 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 26 Oct 2025 (Set A): 20 questions, each solved by Skill-Lync and checked against ISRO's final answer key.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 95 questions on this page

ISRO 2025 · Mechanical Set A · Q.21Part A · 1 mark · -0.33 if wrongHeat transfer

Temperature profile in a plane wall of constant conductivity with internal heat generation

The temperature profile for heat conduction through a wall of constant thermal conductivity in presence of a heat source is

  1. (a)Linear
  2. (b)Parabolic
  3. (c)Logarithmic
  4. (d)Hyperbolic

Answer: (b) Parabolic Official final key: (b)

For steady one-dimensional conduction in a plane wall with uniform volumetric generation and constant , the heat equation is

The second derivative is a constant, . Integrating twice gives , a quadratic in . With equal surface temperatures on a wall of half-thickness it becomes , a parabola with its maximum at the centre.

Linear is the no-generation case (). Logarithmic is the radial profile in a cylinder without generation. So the profile is parabolic.

Where this shows up in industry

Electrical windings, nuclear fuel plates and curing composite laminates all generate heat internally, and the parabolic profile sets the peak centre temperature designers must keep below the material limit.

ISRO 2025 · Mechanical Set A · Q.22Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Mechanism behind the rise in strength and hardness during cold working of metals

What is the primary mechanism responsible for the increase in strength and hardness during cold working of metals?

  1. (a)Formation of new grains through recrystallization
  2. (b)Increase in dislocation density and entanglement, hindering dislocation movement
  3. (c)Reduction of dislocations in the crystal structure
  4. (d)Melting of metal surface layers due to deformation

Answer: (b) Increase in dislocation density and entanglement, hindering dislocation movement Official final key: (b)

Cold working is plastic deformation below the recrystallization temperature. Plastic flow happens by dislocation glide, and during deformation new dislocations are generated continuously (Frank-Read sources), so the dislocation density rises by several orders of magnitude, from about to about .

The dislocations tangle and pin one another, so a higher stress is needed to keep them moving. That is strain (work) hardening: yield strength and hardness go up, ductility goes down. The flow stress grows roughly as , where is the dislocation density.

Option (a) is the reverse: recrystallization during annealing creates new strain-free grains and removes the hardening. Option (c) is also the reverse, and nothing melts in cold work. The answer is (b).

Where this shows up in industry

Cold-drawn wire, cold-rolled sheet and roller-burnished fillets rely on strain hardening for strength; a process annealing step is added when the material becomes too hard to form further.

ISRO 2025 · Mechanical Set A · Q.23Part A · 1 mark · -0.33 if wrongStrength of materials

Bulk modulus of a material with E = 200 GPa and Poisson's ratio 0.3

A material has a Young's modulus of 200 GPa and Poisson's ratio of 0.3. What is its bulk modulus?

  1. (a)100 GPa
  2. (b)153.8 GPa
  3. (c)76.9 GPa
  4. (d)166.7 GPa

Answer: (d) 166.7 GPa Official final key: (d)

For an isotropic linear elastic material the elastic constants are related by

So .

The trap is option (c): is the shear modulus , not the bulk modulus.

Answer: .

Where this shows up in industry

Bulk modulus governs how much a solid propellant grain, a hydraulic component or a deep-sea housing changes volume under pressure, and enters every 3D finite element material card through E and Poisson's ratio.

ISRO 2025 · Mechanical Set A · Q.24Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Degrees of freedom of a linkage driving a wheel that rolls without slipping

Find the total number of degrees of freedom for following system. Assume rolling without slipping.

μ ≠ 0
  1. (a)0
  2. (b)1
  3. (c)2
  4. (d)Cannot be determined

Answer: (b) 1 Official final key: (b)

Use Gruebler's criterion for planar mechanisms: , where counts single-freedom joints and two-freedom joints.

Links: the ground, the crank pivoted to the ground, the connecting rod and the wheel, so .

Joints: crank to ground (revolute), crank to rod (revolute), rod to wheel centre (revolute) and wheel to ground. Rolling without slipping ties the wheel's rotation to its translation, so the contact allows only one relative motion and counts as a single-freedom joint. So , .

If the wheel could slip, the contact would be a two-freedom joint and would be 2, which is the trap in option (c). With and no slip, the system has 1 degree of freedom.

Where this shows up in industry

Mobility counts like this are the first check when laying out rover suspensions, landing-gear linkages and deployable mechanisms: a wrong count means the mechanism either locks up or flops.

ISRO 2025 · Mechanical Set A · Q.25Part A · 1 mark · -0.33 if wrongMachine design

Stiffness of the 8-coil piece of a 20-coil spring of stiffness K cut into 8 and 12 coils

A closed-coil helical compression spring with 20 active coils has a spring stiffness of K. It is cut into two parts having 8 and 12 active coils respectively. What is the stiffness of the spring with 8 active coils?

  1. (a)1.5 K
  2. (b)2.0 K
  3. (c)2.5 K
  4. (d)3.0 K

Answer: (c) 2.5 K Official final key: (c)

The stiffness of a closed-coil helical spring is

Cutting the spring does not change the wire diameter , coil diameter or material , so .

. (The 12-coil part has ; the two in series give back .)

Answer: .

Where this shows up in industry

Spring makers trim coils to tune stiffness for valve springs, clutch springs and the separation springs that push spacecraft stages and satellites apart.

ISRO 2025 · Mechanical Set A · Q.26Part A · 1 mark · -0.33 if wrongMachine design

Life of a ball bearing with dynamic load rating 60,000 N under a 20,000 N load

A ball bearing has a dynamic load rating of 60,000 N and experiences a load of 20,000 N. The expected life in million revolutions is :

  1. (a)8
  2. (b)18
  3. (c)27
  4. (d)64

Answer: (c) 27 Official final key: (c)

The basic rating life of a rolling bearing is million revolutions, with for ball bearings ( for roller bearings).

Option (d), 64, would need a load ratio of 4, and 8 would follow from an exponent of about 1.9. The expected life is 27 million revolutions (with 90 per cent reliability).

Where this shows up in industry

The same cube law is used to size bearings in turbopumps, reaction wheels and machine-tool spindles; halving the load gives eight times the life.

ISRO 2025 · Mechanical Set A · Q.27Part A · 1 mark · -0.33 if wrongHeat transfer

Which statement about the Stanton number in forced convection is true

In forced convection, which of the following is true for Stanton number?

  1. (a)It is the ratio of heat transferred to thermal capacity of fluid
  2. (b)It is the ratio of Nusselt number and Reynolds number
  3. (c)It is the ratio of Nusselt number and Prandtl number
  4. (d)Both (a) and (b)

Answer: (a) It is the ratio of heat transferred to thermal capacity of fluid Official final key: (a)

The Stanton number is defined as

The numerator is the heat transferred to the wall per unit area per unit temperature difference; the denominator is the heat capacity flux of the fluid stream. So statement (a) is the physical meaning of .

In terms of other groups, , because . It is not (that would leave out) and not . Since (b) is false, (d) is false too.

Answer: (a).

Where this shows up in industry

Stanton number appears in Reynolds-Colburn analogies used to estimate heat flux to rocket nozzle walls and re-entry heat shields from skin-friction data.

ISRO 2025 · Mechanical Set A · Q.28Part A · 1 mark · -0.33 if wrongEngineering mechanics

Stress in cable L of a three-pulley system lifting a 70 kN load

A load of 70 kN is lifted using a frictionless pulley system shown in the figure below. At each pulley, cables of square cross section with side of 10 mm are used. The stress in cable “L” will be :

CBA70kNLMNP
  1. (a)100 MPa
  2. (b)200 MPa
  3. (c)400 MPa
  4. (d)700 MPa

Answer: (c) 400 MPa Official final key: (c)

With frictionless pulleys the tension is the same on both sides of each cable, and each hanging pulley is held by a cable carrying twice the tension of the cable that wraps it.

  1. Cable over A: the free end carries , so cable N also carries . Pulley A is held by a cable of tension .
  2. That cable passes over B, so cable M carries , and pulley B is held by a cable of tension .
  3. That cable passes over the fixed pulley C, so cable L carries .

Equilibrium of the load: , so and .

Cable area , so .

Option (d) assumes cable L carries the whole load; option (a) is the stress in cable N. Answer: .

Where this shows up in industry

Tension bookkeeping in pulley and sheave trains is routine in crane, hoist and launch-pad umbilical design, where each rope is sized for its own tension rather than the full load.

ISRO 2025 · Mechanical Set A · Q.30Part A · 1 mark · -0.33 if wrongHeat transfer

View factors F12 and F21 between a horizontal plate and an inclined plate sharing an edge

Determine and for the following configuration having long inclined plates and point is directly above the center of

B100 mmA1A2200 mm
  1. (a),
  2. (b),
  3. (c),
  4. (d),

Answer: (a) , Official final key: (a)

The plates are long, so this is a two-dimensional problem and Hottel's crossed-strings method applies. For two surfaces that share an edge, it reduces to

where is the string joining their free ends.

Take the left end of as the origin. runs from to mm, and is at mm. So , , and the free ends are joined by .

.

Reciprocity (per unit length) gives , so .

Option (b) swaps the two values. Answer: , .

Where this shows up in industry

Crossed-string view factors are a quick hand check on the radiation models used for spacecraft radiator panels, solar-array hinges and furnace walls before running a full Monte Carlo ray-trace.

ISRO 2025 · Mechanical Set A · Q.31Part A · 1 mark · -0.33 if wrongEngineering mechanics

Maximum altitude and time to impact of a booster separated at 1.125 km moving at 200 m/s

A rocket is launched vertically up. It attains the velocity of 200 m/s at an altitude of 1.125 kms. At this point, its booster stage is separated without any relative velocity. Find the maximum altitude the booster stage attains and the time duration between separation and its impact on ground. Consider no drag effect on the separated booster stage and .

  1. (a) km and s
  2. (b) km and s
  3. (c) km and s
  4. (d) km and s

Answer: (d) km and s Official final key: (d)

With no relative velocity at separation, the booster starts at 1125 m moving up at 200 m/s, and then moves under gravity alone.

Further rise: , so .

Time to the top: . Fall from 3125 m from rest: .

Total time from separation to impact: . (Same result from , whose positive root is .)

Option (b) gives only the fall time; option (c) gives only the extra rise. Answer: , .

Where this shows up in industry

Spent-stage trajectory estimates like this, refined with drag, fix the drop zones and range-safety corridors that launch agencies notify before every launch.

ISRO 2025 · Mechanical Set A · Q.32Part A · 1 mark · -0.33 if wrongEngineering mechanics

Angular velocity of a boat moving east at 40 m/s seen by an observer 100 m south of it

A boat is travelling at a speed of 40 m/s due east as shown in the figure below. An observer is stationed 100 m south of the line of travel. Determine the angular velocity of the boat, relative to the observer, when in the position () shown in the figure.

Boat40m/sθ=30°100 mNorthEastObserver
  1. (a)0.3 rad/sec
  2. (b)0.4 rad/sec
  3. (c)0.6 rad/sec
  4. (d)0.8 rad/sec

Answer: (a) 0.3 rad/sec Official final key: (a)

Measure from north, as in the figure. The boat's east coordinate is , with the 100 m north distance fixed.

Differentiate with respect to time: , so

With and : .

Check with relative velocity: the line of sight is long, and the velocity component perpendicular to it is , so .

Option (b), , is the value only when the boat is directly north (). Answer: .

Where this shows up in industry

Ground tracking stations work out exactly this line-of-sight rate to slew antennas and radars onto a rocket or a low-orbit satellite passing overhead.

ISRO 2025 · Mechanical Set A · Q.33Part A · 1 mark · -0.33 if wrongHeat transfer

Dimensionless number for the ratio of thermal diffusivity to mass diffusivity

What is the name of the dimensionless number that characterizes the ratio of thermal to mass diffusivity?

  1. (a)Lewis number
  2. (b)Prandtl number
  3. (c)Reynolds number
  4. (d)Schmidt number

Answer: (a) Lewis number Official final key: (a)

The three diffusivity ratios are:

  • Prandtl number : momentum to thermal diffusivity.
  • Schmidt number : momentum to mass diffusivity.
  • Lewis number : thermal to mass diffusivity.

The Reynolds number compares inertia with viscous forces and is not a diffusivity ratio. Answer: Lewis number.

Where this shows up in industry

Lewis number links heat and mass transfer in cooling towers, evaporative coolers and the transpiration and film cooling of combustor and nozzle walls.

ISRO 2025 · Mechanical Set A · Q.34Part A · 1 mark · -0.33 if wrongMachine design

Axial force for a single plate clutch carrying 50 Nm, friction 0.3, mean radius 0.1 m

A single plate clutch transmits 50 Nm torque with a coefficient of friction 0.3 and mean radius 0.1 m. What is the axial force required?

  1. (a)1000 N
  2. (b)1500 N
  3. (c)1670 N
  4. (d)2000 N

Answer: (c) 1670 N Official final key: (c)

The friction torque on one friction surface is , where is the axial force and the mean radius.

That rounds to 1670 N, option (c), so the options are built on one pair of contact surfaces. Note that a practical single plate clutch has friction lining on both faces of the plate, giving and ; that value is not offered, so use the single-surface relation here.

Answer: .

Where this shows up in industry

The same torque-capacity relation sizes the clamp springs in car and tractor clutches and the friction brakes in machine tools and hoists.

ISRO 2025 · Mechanical Set A · Q.35Part A · 1 mark · -0.33 if wrongStrength of materials

Statements on shear stress, complementary shear stress and shear strain

Consider the following statements related to stress and strain :

  1. Shear stress is always tangential to the face over which it acts.
  2. Shear stresses on the transverse pair of faces are known as complimentary shear stresses.
  3. Shear strain is defined as the change in the right angle of the element measured in radians.

Which of the above statements is correct?

  1. (a)1 and 2 only
  2. (b)1 and 3 only
  3. (c)2 and 3 only
  4. (d)1, 2 and 3

Answer: (d) 1, 2 and 3 Official final key: (d)

Check each statement.

  1. True. Shear stress acts in the plane of the face, i.e. tangential to it; the normal component is the direct stress.
  2. True. If shear stress acts on one pair of opposite faces of an element, moment equilibrium needs an equal shear stress on the perpendicular (transverse) pair. These are the complementary shear stresses. (The paper spells it "complimentary".)
  3. True. Shear strain is the change in the original right angle between two edges of the element, measured in radians.

All three are correct. Answer: (d) 1, 2 and 3.

Where this shows up in industry

Complementary shear is why a bolted lap joint or a bonded composite patch is checked for shear on both the bond plane and the plane at right angles to it.

ISRO 2025 · Mechanical Set A · Q.36Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Heat rejected by a reversible engine taking 250 kJ/s at 227 C and rejecting at 27 C

A heat engine is supplied with 250 KJ/s of heat at a constant fixed temperature of 227°C. The heat is rejected at 27°C and the cycle is reversible. What is the amount of heat rejected?

  1. (a)273 KJ/s
  2. (b)200 KJ/s
  3. (c)180 KJ/s
  4. (d)150 KJ/s

Answer: (d) 150 KJ/s Official final key: (d)

For a reversible (Carnot) engine, with absolute temperatures.

and .

The efficiency is per cent and the power output is . Using Celsius temperatures directly would give a wrong ratio. Answer: .

Where this shows up in industry

The Carnot limit is the benchmark against which real power plants, waste-heat recovery units and spacecraft radioisotope power systems are judged.

ISRO 2025 · Mechanical Set A · Q.37Part A · 1 mark · -0.33 if wrongMachine design

Diameter of three rivets joining two plates under 50 kN with 50 N/mm2 permissible shear

Two plates subjected to tensile force of 50 kN, are fixed together by means of three rivets. The plates and rivets are made of same material. If the permissible shear stress in the rivets is , what is the diameter of the rivets? (Neglect stress concentration effects)

  1. (a)14.75 mm
  2. (b)20.60 mm
  3. (c)24.38 mm
  4. (d)29.52 mm

Answer: (b) 20.60 mm Official final key: (b)

Two plates riveted together form a lap joint, so each rivet is in single shear and the three rivets share the load equally.

, so .

If the rivets were wrongly taken in double shear, would be , close to option (a) but not equal to it. Answer: .

Where this shows up in industry

Riveted lap joints remain standard in aircraft skins and launch-vehicle interstage structures, and rivet sizing starts from exactly this shear check before bearing and tearing are checked.

ISRO 2025 · Mechanical Set A · Q.38Part A · 1 mark · -0.33 if wrongStrength of materials

Cantilever deflection ratio: total load W as a UDL versus the same W at the free end

A cantilever beam carries a load W uniformly distributed over its entire length. If the same load is placed at the free end of the same cantilever, then the ratio of maximum deflection in the first case to that in the second case will be

  1. (a)3/8
  2. (b)8/3
  3. (c)5/8
  4. (d)8/5

Answer: (a) 3/8 Official final key: (a)

Maximum deflection of a cantilever occurs at the free end.

  • Total load spread uniformly (): .
  • Same at the free end: .

Option (b) is the inverse ratio. Answer: .

Where this shows up in industry

Spreading a load instead of concentrating it at the tip is why antenna booms, robot arms and wing spars carry distributed loads far more stiffly than a tip mass of the same weight.

ISRO 2025 · Mechanical Set A · Q.39Part A · 1 mark · -0.33 if wrongStrength of materials

Maximum shear stress when a solid shaft of diameter D is replaced by a hollow D x D/2 one

A solid shaft of diameter ‘D’ undergoes a twisting moment that develops maximum shear stress ‘’. If the shaft is replaced by a hollow one of outside diameter ‘D’ and inside diameter D/2, then the maximum shear stress will be

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a)

For the same torque, , where is the polar section modulus.

Solid: . Hollow with : .

The traps come from the wrong power of : and . Removing the core costs only 6.7 per cent in stress while saving 25 per cent of the material. Answer: .

Where this shows up in industry

Hollow shafts are used in turbopumps, helicopter drive trains and car propeller shafts because the material near the axis carries little torque.

ISRO 2025 · Mechanical Set A · Q.40Part A · 1 mark · -0.33 if wrongHeat transfer

Condition for negligible temperature gradients in a hot sphere quenched in a liquid bath

A hot metal sphere is suddenly immersed in a liquid bath at a much lower temperature than the hot metal sphere. Under which of the following conditions, the temperature gradients in the metal sphere can be assumed to be neglected during the cooling of the sphere?

  1. (a)Nusselt number 1
  2. (b)Biot number 1
  3. (c)Biot number 1
  4. (d)Nusselt number 1

Answer: (c) Biot number 1 Official final key: (c)

The Biot number compares the internal conduction resistance of the solid with the external convection resistance:

with for a sphere. When (in practice ), heat moves through the metal much faster than it leaves the surface, so the temperature inside is nearly uniform and the lumped-capacitance model applies.

means large internal gradients. The Nusselt number uses the fluid's conductivity and describes the convection, not the gradient inside the solid. Answer: .

Where this shows up in industry

Heat-treatment shops use the Biot number to decide whether a quenched part cools uniformly or needs a transient conduction analysis to predict cracking and distortion.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.