ISRO Scientist/Engineer Mechanical 2025 paper: Part A, questions 61 to 80, solved

Questions 61 to 80 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 26 Oct 2025 (Set A): 20 questions, each solved by Skill-Lync and checked against ISRO's final answer key.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 95 questions on this page

ISRO 2025 · Mechanical Set A · Q.61Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

First step in the heat treatment of 18-4-1 high speed steel

Which of the following option is true for heat treatment of HSS 18 : 4 : 1?
  1. (a)First specimen is heated to
  2. (b)First specimen is heated to
  3. (c)First specimen is heated to
  4. (d)None of the above

Answer: (b) First specimen is heated to Official final key: (b)

18-4-1 HSS (18% W, 4% Cr, 1% V) has very low thermal conductivity and a hardening temperature close to its solidus, so it is hardened in stages:

  1. Preheat slowly to about to (roughly ) so the whole section is at one temperature and does not crack from thermal shock.
  2. Transfer quickly to the hardening furnace at about to , hold briefly to dissolve the alloy carbides.
  3. Quench in oil or salt bath.
  4. Temper (usually twice) at about to for secondary hardening.

So the first heating is to about . Option (a) is the second stage and option (c) is the tempering step after the quench. Answer: (b)

Where this shows up in industry

Tool rooms making HSS drills, taps and form tools follow this preheat, harden, double-temper cycle; skipping the preheat is a common cause of cracked tools.

ISRO 2025 · Mechanical Set A · Q.62Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

What Salmon's (Salomon's) hypothesis relates in machining

Salmon's hypothesis relates between
  1. (a)Surface finish and cutting tool geometry
  2. (b)Cutting forces and surface finish
  3. (c)Cutting speed and cutting temperature
  4. (d)Surface finish and cutting temperature

Answer: (c) Cutting speed and cutting temperature Official final key: (c)

Carl Salomon's 1931 hypothesis (spelt Salmon in the paper) is the basis of high-speed machining. He proposed that as cutting speed increases, the cutting temperature first rises to a maximum and then, beyond a critical speed range, falls again.

It is a statement about cutting speed versus cutting temperature. It does not deal with tool geometry, forces or surface finish, although later work on high-speed machining exploits it to get lower forces and better finish. Answer: (c) cutting speed and cutting temperature

Where this shows up in industry

High-speed milling of aluminium aerospace structures relies on running far above conventional speeds; Salomon's idea is the historical argument for why that need not overheat the tool.

ISRO 2025 · Mechanical Set A · Q.63Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Machinability index of SAE 1112 free-cutting steel

Machinability index for SAE1112 steel is
  1. (a)50%
  2. (b)75%
  3. (c)100%
  4. (d)None of the above

Answer: (c) 100% Official final key: (c)

Machinability index (rating) is a relative number: the cutting speed giving a standard tool life (usually 20 or 60 min) on the test material, divided by the speed giving the same tool life on a reference material, times 100.

The AISI/SAE (B)1112 free-cutting, resulphurised steel is that reference, so by definition its index is . Materials easier to machine than 1112 score above 100 (free-cutting brass, aluminium alloys) and harder ones below (stainless steels, titanium). Answer: (c) 100%

Where this shows up in industry

Process planners use machinability ratings to scale cutting speeds when a part moves from one steel grade to another.

ISRO 2025 · Mechanical Set A · Q.64Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Growth of laminar and turbulent boundary layers on a flat plate

Consider the following statement pertaining to boundary layer on a flat plate.
  1. The thickness of laminar boundary layer at a distance from the leading edge varies as .
  2. The thickness of turbulent boundary layer at a distance from the leading edge varies as .
  3. The boundary layer is laminar when Reynolds number is less than .
Which of the above statements are correct?
  1. (a)1, 2 and 3
  2. (b)1 and 2 only
  3. (c)1 and 3 only
  4. (d)2 and 3 only

Answer: (a) 1, 2 and 3 Official final key: (a)

Statement 1. Blasius solution: with . So . True.

Statement 2. With the 1/7th power velocity profile: , so . True.

Statement 3. The critical Reynolds number for a flat plate is taken as ; below it the layer is laminar. True.

All three are correct. Answer: (a) 1, 2 and 3

Where this shows up in industry

Boundary-layer growth sets skin-friction drag and heating on launch-vehicle fairings and on aircraft wings, and decides where transition trips are placed in wind-tunnel models.

ISRO 2025 · Mechanical Set A · Q.65Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Bourdon gauge reading on a closed tank moved to a place with 90 kPa atmosphere

A bourdon gauge connected to a closed tank indicates 40 kPa at a place where the atmospheric pressure is 95.48 kPa. If the tank is carried to a higher elevation where the atmospheric pressure is 90 kPa, the reading of the gauge will be
  1. (a)35 kPa
  2. (b)60.37 kPa
  3. (c)45.48 kPa
  4. (d)25.37 kPa

Answer: (c) 45.48 kPa Official final key: (c)

A Bourdon gauge reads gauge pressure: absolute pressure minus local atmospheric pressure. The tank is closed and rigid, so its absolute pressure does not change when it is moved.

Absolute pressure: .

New gauge reading: .

The reading goes up because the outside pressure acting on the gauge tube has dropped. Option (a) wrongly subtracts the change in atmosphere. Answer: (c)

Where this shows up in industry

Propellant and pressurant tank gauges on launch vehicles read differently on the pad and at altitude for exactly this reason, so flight telemetry uses absolute transducers.

ISRO 2025 · Mechanical Set A · Q.66Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Process variables in metal diffusion bonding

In metal diffusion bonding, which are the process variables?
  1. (a)Pressure and temperature
  2. (b)Pressure and Time
  3. (c)Pressure, temperature and time
  4. (d)Temperature and time

Answer: (c) Pressure, temperature and time Official final key: (c)

Diffusion bonding is a solid-state joining process: clean surfaces are pressed together at high temperature (typically to of the absolute melting point) and held until atoms diffuse across the interface.

  • Pressure collapses surface asperities to give intimate contact, without gross deformation.
  • Temperature sets the diffusion rate.
  • Time lets diffusion close the remaining voids.

All three must be controlled together; any pair alone is incomplete. Answer: (c) pressure, temperature and time

Where this shows up in industry

Diffusion bonding (often with superplastic forming) is used for titanium aerospace panels and for propellant tank and thruster components that need a joint as strong as the parent metal.

ISRO 2025 · Mechanical Set A · Q.67Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

What the symbol H7 represents in an H7/g6 fit

In the H7/g6 fit, the symbol H7 represents :
  1. (a)Shaft with fundamental deviation below the zero line
  2. (b)Hole with fundamental deviation above the zero line
  3. (c)Hole with tolerance zone starting at the basic size
  4. (d)Shaft with tight interference

Answer: (c) Hole with tolerance zone starting at the basic size Official final key: (c)

In ISO limits and fits, upper-case letters denote holes and lower-case letters denote shafts; the number is the IT tolerance grade. So H7 is a hole of grade IT7.

For the H hole the fundamental deviation (lower deviation EI) is zero: the tolerance zone starts exactly on the zero line, i.e. at the basic size, and extends upward by IT7. This is the basic hole of the hole-basis system.

Option (b) is the trap: holes A to G have their fundamental deviation shifted above the zero line, but H has none. Options (a) and (d) describe shafts. Answer: (c) hole with tolerance zone starting at the basic size

Where this shows up in industry

H7/g6 is the standard sliding or locating fit for gears and pulleys on shafts and for precision bores in gearboxes and actuators.

ISRO 2025 · Mechanical Set A · Q.68Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Actual length when a scale with +0.05 mm per 100 mm error reads 5 m

A linear measuring scale has a known systematic error of + 0.05 mm for every 100 mm of measurement. If this scale is used to measure a distance and the reading obtained is 5 meters, what is the actual length of the distance?
  1. (a)4995.00 mm
  2. (b)5002.50 mm
  3. (c)5000.00 mm
  4. (d)4997.50 mm

Answer: (d) 4997.50 mm Official final key: (d)

A positive systematic error means the scale reads more than the true length. The correction is therefore the error with its sign reversed.

Error over the reading: .

Actual length: .

Adding the error instead of subtracting it gives option (b). Answer: (d)

Where this shows up in industry

Calibration certificates for scales, tapes and laser trackers list such systematic errors so measured lengths can be corrected during inspection.

ISRO 2025 · Mechanical Set A · Q.69Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Least count of a micrometer with 0.5 mm pitch and 50 thimble divisions

What is the least count of a micrometre with a pitch of 0.5 mm and a thimble having 50 divisions?
  1. (a)0.01 mm
  2. (b)0.005 mm
  3. (c)0.02 mm
  4. (d)0.001 mm

Answer: (a) 0.01 mm Official final key: (a)

The least count is the pitch divided by the number of thimble divisions.

Answer: (a)

Where this shows up in industry

The standard outside micrometer on every machine-shop bench has exactly this 0.5 mm pitch, 50-division thimble.

ISRO 2025 · Mechanical Set A · Q.70Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Least count of a screw gauge moving 1 mm in two rotations with 100 divisions

A screw gauge moves 1 mm when two rotations were given. If the circular scale (near thimble) has 100 divisions marked circumferentially, what will be the least count?
  1. (a)0.001
  2. (b)0.020
  3. (c)0.010
  4. (d)0.005

Answer: (d) 0.005 Official final key: (d)

First find the pitch (advance per rotation), then divide by the circular-scale divisions.

Pitch .

Taking the pitch as 1 mm (forgetting the two rotations) gives option (c). Answer: (d)

Where this shows up in industry

Finer-pitch screw gauges and micrometer heads are used where 5 micrometre resolution is needed, such as checking sheet and foil thickness.

ISRO 2025 · Mechanical Set A · Q.71Part A · 1 mark · -0.33 if wrongHeat transfer

Temperature behaviour for flow in a tube with constant surface heat flux

Which of the following is true for the scenario of a fluid flowing along a tube and a constant heat flux applied on the tube surface?
  1. (a)The mean temperature of the fluid varies linearly along the tube length
  2. (b)The surface temperature of the tube varies linearly along the tube length
  3. (c)The difference between the tube surface temperature and mean fluid temperature remains constant throughout the tube length
  4. (d)All of the above

Answer: (d) All of the above Official final key: (d) · provisional key was (a)

Mean temperature. An energy balance on a length gives . With constant, is constant, so rises linearly. (a) is true.

Temperature difference. . In the thermally fully developed region is constant, so is constant. (c) is true.

Surface temperature. is a linear function plus a constant, so it is also linear and parallel to . (b) is true.

All three hold for the standard fully developed case (near the entrance is higher, so the gap is smaller there). Answer: (d) all of the above

ISRO's provisional key gave (a); the final key after objections is (d).

Where this shows up in industry

Electrically heated tubes, nuclear fuel channels and regeneratively cooled rocket nozzle passages are designed with the constant-flux model, where the wall runs a fixed margin above the coolant.

ISRO 2025 · Mechanical Set A · Q.72Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Most suitable actuator for simple on-off control such as door locks

Which of the following actuators is most suitable for simple binary (on-off) control applications such as door locks?
  1. (a)Stepper motor
  2. (b)Solenoid actuator
  3. (c)Proportional hydraulic actuator
  4. (d)Shape Memory Alloy (SMA) actuator

Answer: (b) Solenoid actuator Official final key: (b)

A solenoid is a coil around a movable iron plunger. Energising the coil pulls the plunger to one end; a spring returns it when the current stops. It has just two positions, switches in milliseconds, and needs only a switch or transistor to drive it, which is exactly what a lock or latch needs.

A stepper motor gives precise incremental positioning and needs a driver; proportional hydraulics gives continuously variable force and is bulky; SMA actuators are slow (heat and cool cycles) with limited force and life. They can be made to work, but none is the simplest fit. Answer: (b) solenoid actuator

Where this shows up in industry

Solenoids drive car central locking, fuel injectors, solenoid valves in propellant feed systems and latches in test rigs.

ISRO 2025 · Mechanical Set A · Q.73Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Which quantity is not a rigid body parameter in multibody dynamics simulation

In multibody dynamics simulation, which of the following is typically not considered a rigid body parameter?
  1. (a)Mass
  2. (b)Inertia tensor
  3. (c)Damping coefficient
  4. (d)Center of gravity

Answer: (c) Damping coefficient Official final key: (c)

A rigid body in a multibody model is defined by its inertial properties: mass, the location of its centre of gravity, and its inertia tensor about that point (plus its initial position and velocity).

Damping is not a property of a rigid body; it is energy dissipation in the connections: dampers, bushings, joint friction and contact elements defined between bodies. Answer: (c) damping coefficient

Where this shows up in industry

Tools such as Adams or Simscape Multibody model spacecraft appendage deployment and vehicle suspensions this way: bodies carry mass properties, connectors carry stiffness and damping.

ISRO 2025 · Mechanical Set A · Q.74Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Build material typically used in Selective Laser Sintering (SLS)

In Selective Laser Sintering (SLS), what is typically used as the build material?
  1. (a)Liquid photopolymer
  2. (b)Thermoplastic filament
  3. (c)UV-curable resin
  4. (d)Powdered polymers or metals

Answer: (d) Powdered polymers or metals Official final key: (d)

SLS spreads a thin layer of powder, and a laser scans each cross-section to sinter (fuse) the particles. A fresh layer is spread and the process repeats; unfused powder supports the part.

Typical materials are polyamide (nylon) powders; the same principle with metal powders is DMLS/SLM. Liquid photopolymer and UV resin belong to stereolithography, and filament to FDM. Answer: (d) powdered polymers or metals

Where this shows up in industry

Powder-bed laser processes make nylon ducting and brackets, and in metal form, rocket engine injectors and turbopump parts.

ISRO 2025 · Mechanical Set A · Q.75Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Additive manufacturing process that cures liquid resin with a UV laser

Which additive manufacturing process involves curing liquid resin using a UV laser?
  1. (a)Fused Deposition Modeling (FDM)
  2. (b)Selective Laser Sintering (SLS)
  3. (c)Stereolithography (SLA)
  4. (d)Electron Beam Melting (EBM)

Answer: (c) Stereolithography (SLA) Official final key: (c)

Stereolithography uses a UV laser to trace each layer on the surface of a vat of liquid photopolymer; the resin polymerises (cures) where the laser hits it. The platform moves by one layer and the next is traced.

FDM extrudes molten thermoplastic, SLS fuses powder with a laser, and EBM melts metal powder with an electron beam. Answer: (c) stereolithography (SLA)

Where this shows up in industry

SLA gives the finest surface finish among polymer processes and is used for wind-tunnel models, casting patterns and fit-check prototypes.

ISRO 2025 · Mechanical Set A · Q.76Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Break-even quantity for price Rs 300, variable cost Rs 200 and fixed cost Rs 50,000

If the selling price is Rs. 300/unit, variable cost is Rs. 200/unit, and fixed cost is Rs. 50,000, what is the break-even quantity?
  1. (a)100 units
  2. (b)150 units
  3. (c)200 units
  4. (d)500 units

Answer: (d) 500 units Official final key: (d)

At break-even, revenue equals total cost: , so . Each unit contributes towards the fixed cost.

Answer: (d) 500 units

Where this shows up in industry

Break-even analysis decides whether to make a part in-house on a new machine or buy it from a supplier.

ISRO 2025 · Mechanical Set A · Q.77Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Fifth-year sum-of-years-digits depreciation: cost Rs 11,000, 9-year life, salvage Rs 2,000

A machine is purchased at a cost of Rs. 11,000. The assumed useful life is 9 years and the salvage value is Rs. 2,000. Based on sum of year digits method the depreciation for the fifth year would be Rs.
  1. (a)1,500
  2. (b)1,200
  3. (c)1,000
  4. (d)800

Answer: (c) 1,000 Official final key: (c)

Sum-of-years digits: the depreciation in year is the remaining life at the start of year , divided by the sum of the year digits, times the depreciable amount (cost minus salvage).

Sum of digits: . Depreciable amount: .

Remaining life at the start of year 5: .

Check: year 1 is and the charge falls by 200 each year (1800, 1600, 1400, 1200, 1000), so year 5 is 1000. Year 5 is the middle of a 9-year life, so counting the digits from either end gives 5 here. Answer: (c) Rs. 1,000

Where this shows up in industry

Accelerated depreciation methods like this are used when costing machine-hour rates for new CNC equipment.

ISRO 2025 · Mechanical Set A · Q.78Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

PERT expected time with optimistic 8, most likely 10 and pessimistic 14 min

In a small engineering project, three time estimates of a PERT activity are : Optimistic time min, Most likely time min, Pessimistic time min The expected time of the activity would be :
  1. (a)12.13 min
  2. (b)10.33 min
  3. (c)10.76 min
  4. (d)11.25 min

Answer: (b) 10.33 min Official final key: (b)

PERT assumes a beta distribution for activity time, giving the expected time

Answer: (b)

Where this shows up in industry

PERT three-point estimates are used to schedule launch campaign and integration activities where durations are uncertain.

ISRO 2025 · Mechanical Set A · Q.79Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Sum of teeth in a gear pair with 200 mm centre distance and module 5 mm

For a gear pair, the center distance is 200 mm, and the module is 5 mm. The sum of teeth in the gear pair is:
  1. (a)40
  2. (b)80
  3. (c)60
  4. (d)100

Answer: (b) 80 Official final key: (b)

Pitch diameter , and for external gears the centre distance is half the sum of the pitch diameters:

Forgetting the factor 2 gives option (a). Answer: (b) 80

Where this shows up in industry

Gearbox designers fix the centre distance first (housing size) and then choose module and tooth numbers to fit it.

ISRO 2025 · Mechanical Set A · Q.80Part A · 1 mark · -0.33 if wrongHeat transfer

Minimum number of tubes in a shell-and-tube steam condenser

A shell-and-tube heat exchanger (1 shell pass, 2 tube passes) is to be used to condense 2.73 kg/s of saturated steam at 340 K. Condensation occurs on the outer tube surfaces and the corresponding convection coefficient is 10,000 . The temperature of the cooling water entering the tubes is and the exit temperature is not to exceed . Thin-walled tubes of 19 mm diameter are to be used and the mean velocity of water flow through the tubes is to be maintained at 0.5 m/s. Determine the minimum number of tubes that should be used?
Water properties: , , , ,
  1. (a)680
  2. (b)720
  3. (c)460
  4. (d)920

Answer: (b) 720 Official final key: (b)

The number of tubes is fixed by how much water must flow, and the water flow is fixed by the heat to be removed with at most a rise. The convection coefficient, and are not needed for this part (they are used to find the tube length).

Heat load. .

Minimum water flow (exit at the limit):

Flow per tube at : .

A higher exit temperature is not allowed, so a smaller water flow (and fewer tubes) is not possible; this is the minimum. With 2 tube passes this is the number of tubes in each pass. Answer: (b) 720

Where this shows up in industry

Surface condensers in power plants and the steam condensers of rocket engine test stands are sized first on cooling-water flow and velocity like this, then on area.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.