ISRO Scientist/Engineer Mechanical 2025 paper: Part A, questions 41 to 60, solved

Questions 41 to 60 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 26 Oct 2025 (Set A): 20 questions, each solved by Skill-Lync and checked against ISRO's final answer key.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 95 questions on this page

ISRO 2025 · Mechanical Set A · Q.41Part A · 1 mark · -0.33 if wrongStrength of materials

Thermal stress in a heated rod restrained by a 50 kN/m spring

A rod has coefficient of thermal expansion and Young’s modulus 200 GPa. It is fitted snugly between the supports as shown in the figure and heated.

The stress induced in it due to rise in temperature will be

10 mm ϕk = 50 kN/m0.5 m
  1. (a)0.1 MPa
  2. (b) MPa
  3. (c) MPa
  4. (d)0.2 MPa

Answer: (c) MPa Official final key: (c)

The rod is not held by two rigid walls. One end pushes against a spring, so the rod can expand and the spring compresses. The rod and the spring act in series: the free expansion is shared between the rod's elastic shortening and the spring's deflection, and both carry the same force .

Free thermal expansion: .

Area . Rod stiffness , which is about 600 times the spring's , so the spring takes almost all of the expansion.

Stress , compressive (the rod pushes on the spring), so with the tensile-positive sign convention: .

Trap: treating both ends as rigid gives , which is not among the options. The spring is what makes the stress tiny, and the sign is negative because the rod is in compression.

Where this shows up in industry

Spacecraft propellant lines and structural struts are often mounted on flexible brackets or bellows for exactly this reason: a compliant support turns a large thermal stress into a small spring load as the part heats in orbit.

ISRO 2025 · Mechanical Set A · Q.42Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Change in natural frequency of a cantilever with end mass when its length is halved

A cantilever beam of negligible mass has a mass at its free end. If the length of the cantilever is halved, what is the factor by which its natural frequency is increased?

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (d) Official final key: (d)

Tip stiffness of a cantilever under an end load: . The natural frequency of the end mass is , so .

Halving the length makes the beam 8 times stiffer, and the frequency rises by : .

Option (a), , is the right number inverted: it is the factor by which the frequency would fall if the length were doubled.

Where this shows up in industry

Antenna booms, solar-array arms and instrument masts on satellites are sized so their first cantilever mode stays well above the launch vehicle's excitation band; shortening the boom is the quickest way to raise that frequency.

ISRO 2025 · Mechanical Set A · Q.43Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Inversion of a mechanism: definition

Inversion of a mechanism is

  1. (a)Changing of a higher pair to lower pair
  2. (b)Obtained by fixing different links in a kinematic chain
  3. (c)Turning it upside down
  4. (d)Obtained by reversing the input and output motion

Answer: (b) Obtained by fixing different links in a kinematic chain Official final key: (b)

A kinematic chain becomes a mechanism when one of its links is fixed as the frame. Fixing a different link of the same chain gives a different mechanism: that is an inversion. The relative motion between links does not change, but the absolute motions seen by an observer do.

Example: the four inversions of the single slider-crank chain give the reciprocating engine, the Whitworth quick-return mechanism, the oscillating-cylinder engine and the hand pump.

(a) describes replacing a higher pair by an equivalent lower-pair linkage, (c) changes nothing kinematic, and (d) only swaps driver and follower. Answer: (b).

Where this shows up in industry

Designers use inversions to get several machines from one chain: the same four-bar or slider-crank geometry, with a different link grounded, becomes a pump, a quick-return shaper drive or a deployment linkage.

ISRO 2025 · Mechanical Set A · Q.44Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Air velocity for dynamic similarity of a sphere tested in a wind tunnel

A sphere is moving in water with a velocity of 1.6 m/s. Another sphere of twice the diameter is placed in a wind tunnel and tested with air which is 750 times less dense and 60 times less viscous than water. The velocity of air that will give dynamically similar condition is

  1. (a)5 m/s
  2. (b)10 m/s
  3. (c)20 m/s
  4. (d)40 m/s

Answer: (b) 10 m/s Official final key: (b)

A fully submerged sphere has no free surface, so viscous forces govern and dynamic similarity means equal Reynolds numbers: .

So .

.

Common slip: multiplying by 60 instead of dividing. Air being 60 times less viscous helps the Reynolds number, so it lowers the required speed.

Where this shows up in industry

Wind-tunnel and water-tunnel tests of launch-vehicle fairings, rocket nozzles and car bodies are planned the same way: match the governing dimensionless number, then pick the test speed from the fluid properties and model scale.

ISRO 2025 · Mechanical Set A · Q.45Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Unbalanced force ratio: full mass at 3000 rpm vs half mass at 300 rpm

In the statement, an eccentric mass rotating at 3000 rpm will create X times more unbalanced force than 50% of the same mass rotating at 300 rpm, ‘X’ will be

  1. (a)10
  2. (b)50
  3. (c)100
  4. (d)200

Answer: (d) 200 Official final key: (d)

The centrifugal (unbalanced) force of an eccentric mass is , so it is proportional to the mass and to the square of the speed, for the same eccentricity .

.

The speed ratio alone gives , option (c). That misses the second factor of 2 from the halved mass on the slower rotor.

Where this shows up in industry

This square law is why turbopumps in liquid rocket engines, which spin at tens of thousands of rpm, need far tighter balance grades than slow industrial fans: a tiny residual unbalance becomes a large bearing load at speed.

ISRO 2025 · Mechanical Set A · Q.46Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Critical damping coefficient of a 10 kg mass on a 0.49 N/mm spring

A mass of 10 kg is attached to the end of a spring with a stiffness 0.49 N/mm. The critical damping coefficient of this system is

  1. (a)14
  2. (b)70
  3. (c)140
  4. (d)700

Answer: (c) 140 Official final key: (c)

Critical damping coefficient: .

Convert the stiffness to SI first: .

.

Leaving in N/mm gives , and forgetting the factor 2 gives 70 (option b), which is only.

Where this shows up in industry

Shock absorbers, landing-gear dampers and isolators for spacecraft electronics boxes are specified as a fraction of critical damping, so is the first number computed in any suspension or mount design.

ISRO 2025 · Mechanical Set A · Q.47Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Frequency ratio for transmissibility below unity at any damping

In a vibration isolation system, the transmissibility will be less than unity for all values of damping factors, if the ratio of forcing frequency to natural frequency is

  1. (a)equal to 1
  2. (b)less than
  3. (c)more than
  4. (d)equal to 2

Answer: (c) more than Official final key: (c)

With frequency ratio and damping factor , the transmissibility is

needs , that is . The damping term cancels out of this condition, so all curves pass through at and stay below 1 beyond it, whatever is.

At (resonance) and for , the force is amplified. also gives , but it is one value inside the range, not the condition. Answer: (c) more than .

Where this shows up in industry

Isolators for reaction wheels, cryocoolers and launch-load mounts are tuned so the disturbance frequency sits well beyond times the mount frequency; below that, the soft mount makes vibration worse, not better.

ISRO 2025 · Mechanical Set A · Q.48Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Maximum number of nodes in a multi-rotor torsional system

In a multi-rotor system of torsional vibrations, maximum number of nodes that can occur is

  1. (a)Two
  2. (b)Equal to number of rotors plus one
  3. (c)Equal to number of rotors
  4. (d)Equal to number of rotors minus one

Answer: (d) Equal to number of rotors minus one Official final key: (d) · provisional key was (c)

A shaft carrying rotors (free at both ends) has degrees of freedom. One of them is rigid-body rotation with no twist and no node. The other are true torsional modes: the first has one node, the second two, and so on.

A node is a section of zero angular motion and lies on a shaft segment between two rotors. There are only segments, and the highest mode puts one node in each. So the maximum number of nodes is : a two-rotor system has one node, a three-rotor system up to two.

Answer: (d) equal to number of rotors minus one.

ISRO's provisional key gave (c); the final key after objections is (d).

Where this shows up in industry

Torsional analysis of engine crankshafts, gearbox trains and turbopump shafts uses this multi-rotor model (Holzer's method) to find each mode and where its nodes fall, so couplings and dampers are placed away from them.

ISRO 2025 · Mechanical Set A · Q.50Part A · 1 mark · -0.33 if wrongStrength of materials

Uniform bar diameter giving the same extension as a tapered bar

A tapering bar (diameters of end sections being and ) and a bar of uniform cross-section have the same length and are subjected to the same axial pull. Both the bars will have same extension if is equal to

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Official final key: (b)

Extension of a bar whose diameter varies linearly from to (integrate along the length):

Extension of a uniform bar of diameter : .

Setting gives , so , the geometric mean of the end diameters.

The arithmetic mean is the trap: it is always larger than , so a bar of that diameter is stiffer and stretches less than the taper.

Where this shows up in industry

Tapered members such as interstage struts, connecting rods and tapered bolts are replaced by an equivalent uniform bar in quick stiffness estimates, using this geometric-mean diameter.

ISRO 2025 · Mechanical Set A · Q.51Part A · 1 mark · -0.33 if wrongStrength of materials

Type of stress in the copper bar of a heated copper-steel composite

A bar of copper and steel together forms a composite system are heated to a temperature of 40°C. What type of stress is induced in the copper bar?

  1. (a)Tensile
  2. (b)Compressive
  3. (c)Shear
  4. (d)Tensile as well as compressive

Answer: (b) Compressive Official final key: (b)

Copper expands more than steel for the same temperature rise: against .

Because the two bars are joined, they must end at a common length that lies between their free expansions. Copper is held back from its free length, so it is compressed; steel is stretched beyond its free length, so it is in tension. Equilibrium: .

Copper: compressive (b). Tensile stress appears in the steel, not the copper, which is why (d) is wrong for the copper bar alone.

Where this shows up in industry

The same mismatch drives stresses in bimetallic strips, brazed copper-steel rocket chamber liners and solder joints on electronics boards that cycle between hot and cold.

ISRO 2025 · Mechanical Set A · Q.52Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Variation of terminal velocity with sphere diameter in a viscous fluid

For solid sphere falling vertically downwards under gravity in a viscous fluid, the terminal velocity varies with diameter of the sphere as :

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Official final key: (b)

(The paper writes for 'proportional to', .)

At terminal velocity, the weight equals buoyancy plus drag. In the viscous (Stokes) regime the drag is :

. Doubling the diameter makes the sphere fall four times faster.

belongs to the opposite limit, high Reynolds number with a constant drag coefficient, not to a viscous fluid.

Where this shows up in industry

Stokes' law sets settling rates in viscometers, propellant slurry mixing, particle filters and sedimentation tanks, and is used to estimate how long debris or droplets stay suspended in a fluid.

ISRO 2025 · Mechanical Set A · Q.53Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Mechanical efficiency of a lathe: 2.5 kW input, 800 N force at 90 m/min

The power required for a turning operation is measured as 2.5 kW. If the cutting force is 800 N and the cutting speed is 90 m/min, calculate the mechanical efficiency.

  1. (a)86.4%
  2. (b)55.5%
  3. (c)40.8%
  4. (d)48%

Answer: (d) 48% Official final key: (d)

Power actually used at the tool tip is cutting force times cutting speed. Convert the speed to m/s: .

Mechanical efficiency .

.

The rest of the measured 2.5 kW goes into friction in the spindle bearings, gears and drive.

Where this shows up in industry

Machine shops use this ratio to size lathe motors and to spot worn spindles or gearboxes: a falling efficiency at a known cutting load shows rising friction losses in the drive.

ISRO 2025 · Mechanical Set A · Q.54Part A · 1 mark · -0.33 if wrongEngineering mathematics

Rate of temperature change felt by a rising weather balloon

A weather balloon is rising vertically in the atmosphere. Temperature (T) at any point depends on both time (t) and altitude (h). The balloon rises with a vertical velocity of 10 m/s. For a given time the change in temperature with respect to altitude is . Similarly for a given altitude, the change in temperature with respect to time is . The total change in temperature () experienced by the balloon is :

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a)

Temperature is and the balloon's altitude changes with time, so the rate it feels is the total (material) derivative, by the chain rule:

Substitute: .

.

Option (d), , is only the local change at a fixed altitude; it ignores the balloon carrying itself into colder air.

Where this shows up in industry

The same material derivative appears in fluid mechanics (local plus convective acceleration) and in trajectory analysis, where a launch vehicle's sensors see atmospheric changes due to both time and the vehicle's own climb.

ISRO 2025 · Mechanical Set A · Q.55Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Velocity potential for the stream function x^2 - y^2

For a two-dimensional, steady, incompressible and irrotational flow, a stream function is given by . The potential function of the flow will be :

  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Official final key: (b)

With , using , : , . The flow is irrotational (), so a potential exists.

With the convention , :

Then must equal , so and is a constant.

.

Options (a) and (d) stop halfway: the leftover function is fixed by the second velocity component and turns out to be a constant. (If is used, the result is ; the sign only depends on convention, and (b) is the only option of the correct form.)

Where this shows up in industry

Potential-flow solutions like this corner flow are the building blocks of panel methods used for quick aerodynamic loads on wings, nose cones and intake lips before a full CFD run.

ISRO 2025 · Mechanical Set A · Q.56Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Spindle speed for a 100 mm face mill at 1 m/s cutting speed

In face milling with a cutter of 100 mm diameter, if the cutting speed is 1 m/s, what should be the spindle speed (rpm)?

  1. (a)190
  2. (b)150
  3. (c)180
  4. (d)120

Answer: (a) 190 Official final key: (a)

Cutting speed is the peripheral speed of the cutter: with in m, in rpm and in m/s.

, so the nearest option is 190 rpm.

Where this shows up in industry

Every CNC milling program sets spindle rpm this way from the tool diameter and the recommended surface speed for the tool-workpiece pair, then derives the feed from feed per tooth.

ISRO 2025 · Mechanical Set A · Q.57Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Why brass is gas welded with an oxidising flame

Brass is welded using oxidizing flame due to

  1. (a) is prevented entering from the atmosphere
  2. (b)Zinc is prevented from evaporating
  3. (c)Zinc is oxidised
  4. (d)All of the above

Answer: (b) Zinc is prevented from evaporating Official final key: (b)

Brass is a copper-zinc alloy, and zinc boils at about , well below the melting range of brass. In a neutral flame the zinc fumes off, leaving a porous, zinc-poor weld and toxic zinc oxide smoke.

An oxidising flame (excess oxygen) forms a thin film of zinc oxide over the molten pool. That film seals the surface and stops further zinc from vaporising. So the reason for using the oxidising flame is (b) to prevent zinc from evaporating.

(c) describes the mechanism (a surface skin of oxidised zinc) rather than the purpose, and (a) is wrong because the flame supplies extra oxygen, so (d) fails too.

Where this shows up in industry

Brazing and gas welding of brass fittings, radiator cores and plumbing hardware rely on this oxidising-flame practice (or a flux) to keep the zinc content, and hence the strength and colour, of the joint.

ISRO 2025 · Mechanical Set A · Q.58Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Equation that describes a thermodynamic system undergoing a phase transition

Which of the following equations describes the behaviour of a thermodynamic system undergoing a phase transition?

  1. (a)Clausius-Clapeyron equation
  2. (b)Van der Waals equation
  3. (c)Maxwell-Boltzmann distribution
  4. (d)Gibbs-Duhem equation

Answer: (a) Clausius-Clapeyron equation Official final key: (a)

The Clausius-Clapeyron equation gives the slope of the saturation (coexistence) curve between two phases, derived from equal Gibbs energies of the phases and a Maxwell relation:

It links the latent heat to how saturation pressure changes with temperature, which is exactly the behaviour during a phase change. Answer: (a).

Van der Waals is a real-gas equation of state, Maxwell-Boltzmann is a molecular speed distribution, and Gibbs-Duhem relates chemical potentials in a mixture; none of them describes the phase transition itself.

Where this shows up in industry

Vapour-pressure curves for cryogenic propellants such as liquid oxygen and hydrogen, and refrigerant saturation tables, are fitted and extrapolated with Clausius-Clapeyron to size tank pressurisation and boil-off.

ISRO 2025 · Mechanical Set A · Q.59Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

HSS tool life at 24 m/min from 3 hours at 18 m/min, n = 0.125

The useful tool life of a HSS tool machining MS at 18 m/min is 3 hours. Calculate the tool life when the tool operates at 24 m/min. Assume ‘’’ (exponent) which depends on cutting conditions as 0.125?

  1. (a)28 min
  2. (b)18 min
  3. (c)14 min
  4. (d)22 min

Answer: (b) 18 min Official final key: (b)

Taylor's tool life equation: , so .

, so .

. A one-third rise in speed cuts the tool life to a tenth, because is a steep exponent for HSS.

Where this shows up in industry

Process planners use Taylor's equation to trade cutting speed against tool changes; for HSS the low means a small speed increase sharply raises tool cost and downtime.

ISRO 2025 · Mechanical Set A · Q.60Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Cause of weld decay in stainless steel

Weld decay in stainless steel is due to

  1. (a)Depletion of Chromium at heat affected zone
  2. (b)Depletion of Titanium in the weld
  3. (c)Both (a) and (b)
  4. (d)None of the above

Answer: (a) Depletion of Chromium at heat affected zone Official final key: (a)

In austenitic stainless steel, the part of the heat-affected zone that stays in roughly to during welding lets carbon combine with chromium as chromium carbide () at the grain boundaries. This is called sensitisation.

The metal next to those boundaries drops below the roughly chromium needed for a passive film, so it corrodes along the grain boundaries in service: weld decay. Answer: (a) depletion of chromium in the heat-affected zone.

Titanium (or niobium) is added deliberately to stabilise the steel: it grabs the carbon first so chromium stays in solution. Its loss is not the cause, so (b) and (c) are wrong. Low-carbon grades (304L, 316L) are the other cure.

Where this shows up in industry

Stainless propellant feed lines, cryogenic tanks and chemical plant piping are made from L-grade or stabilised steels, or solution-annealed after welding, precisely to avoid weld decay.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.