GATE Electronics (EC): Networks (nodal and mesh analysis, Thevenin and Norton, AC phasors and power, resonance, RL, RC and RLC transients, Laplace, two-port parameters), previous-year questions solved, part 4

Part 4 of 4 of the Networks: Theorems, AC, Transients hub: 5 more official GATE EC questions on two-port networks, each solved step by step and checked against the official answer key. Part 1 covers DC circuit analysis: nodal, mesh, superposition, Thevenin and Norton, AC steady state: phasors, impedance, power and resonance and transients and Laplace analysis of RL, RC and RLC circuits.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 5 of 24 questions on this page

GATE 2022 · EC · Q.54NAT · 2 marksTwo-port networks

Two-port with 10 V on Port 1, V2 = 5 V open and 4 V at I2 = -4 mA: I2 with a 1 kOhm and 10 V load?

A linear -port network is shown in Fig. (a). An ideal DC voltage source of is connected across Port . A variable resistance is connected across Port . As is varied, the measured voltage and current at Port is shown in Fig. (b) as a versus plot. Note that for , , and for , .

When the variable resistance at Port is replaced by the load shown in Fig. (c), the current is _______ mA (rounded off to one decimal place).
Figure (a): a linear two-port network with a 10 volt DC source across Port 1 (current I1 into the network, voltage V1 plus at the top) and a variable resistance R across Port 2 (current I2 into the network at terminal A, voltage V2 plus at A, terminal B below). Figure (b): V2 against minus I2 is a straight falling line, 5 volt at zero current and 4 volt at minus I2 equal to 4 milliampere. Figure (c): terminal A, a 1 kilo-ohm resistor, a 10 volt battery with its plus plate towards the resistor, then terminal BNetwork10 VI1 +−V1 I2 ABR+−V2 (a)5 V4 V4 mAV2 −I2 (b)A1 kΩB10 V(c)

Answer: Official key: 3.9 to 4.1

  1. Port is held at the whole time, so as seen from Port the linear network is just a Thevenin source: , with the current into the network at terminal (the direction marked in Fig. (a)).
  2. Read the plot. At (port open) , so . At , , so . In , and : .
  3. Now the load of Fig. (c): a resistor in series with a battery whose plus plate is on the resistor side (towards ). flows out of the load into , so the voltage at is .
  4. Equate the two relations at the port: , so and .
  5. Check: , and . The sign is positive, so the current really flows into the network: the battery is stronger than the the network produces on its own.

Trap: three slips land outside the official range to . Ignoring gives . Using the plot with the wrong sign, , gives . Reading the battery as reversed gives . The code built two different internal networks (a divider with and in series at Port , and with ), checked that both reproduce the plot ( open, at , ) by solving the nodal equations, and then solved both with the Fig. (c) load: and . The answer depends only on and , not on what is inside the box.

Where this shows up in industry

Characterising a block by measuring its port voltage and current with a few different loads, then replacing it with a Thevenin or Norton model, is exactly how engineers treat a power supply, a sensor output or a measured two-port in S-parameter work: the model predicts the behaviour with any new load without knowing the internals.

GATE 2023 · EC · Q.33NAT · 1 markTwo-port networks

Two-port with [Y] = (1/100)[[2, -1], [-1, 4/3]] S, 120 V source and 10 Ohm: load for maximum power?

For the two port network shown below, the -parameters is given as . The value of load impedance , in , for maximum power transfer will be _______ (rounded off to the nearest integer).
A 120 volt source in series with a 10 ohm resistor drives port 1 of a two-port network whose admittance matrix [Y] is given. A load impedance Z_L is connected across port 210 Ω+−120 V[Y]ZL

Answer: Official key: 80 to 80

  1. Maximum power transfer to happens when equals the conjugate of the Thevenin impedance seen from port 2 looking back into the two-port and the source. So find at port 2.
  2. Port equations (currents into the two-port): and (here ). The source side gives .
  3. Kill the source (short it), so . Then , so and . Hence .
  4. . So , a pure resistance, and .
  5. Check: with port 2 open (), , and , so and . Maximum power is .

Trap: using ignores the on the source side, which changes the output impedance because couples the ports. The code solved the four port equations with a test source at port 2 and the source shorted: . It also swept a resistive load from to with the real source and found the maximum load power (20.00 W) at 80.00 .

Where this shows up in industry

Matching a load to the output impedance of a two-port is the daily job of RF amplifier and antenna design, where y, z and S parameters are measured and the source and load are tuned for maximum power transfer. The same Thevenin step gives the output impedance of any stage with feedback.

GATE 2024 · EC · Q.60NAT · 2 marksTwo-port networks

Two-port with 2 Ohm series, 4 Ohm shunt and a 8 V1 controlled source: Y21 in siemens?

For the two port network shown below, the value of the parameter (in Siemens) is ______.
Two-port network. Port 1 (terminals 1 and 1', V1 plus at the top, current I1 flowing in) connects through a 2 ohm series resistor to a middle node, which is also directly connected to terminal 2 (port 2 with V2 plus at the top and current I2 flowing in). From the middle node, a 4 ohm resistor in series with a controlled voltage source 8 times V1 goes to the bottom wire joining 1' and 2'. The controlled source has its minus terminal at the top, next to the 4 ohm resistor, and its plus terminal at the bottomI12 ΩI24 Ω−+8V1 11'22'+−V1+−V2

Answer: Official key: 1.5 to 1.5

  1. The definition is . Short port 2. The middle node is then at , the same as the bottom wire.
  2. The resistor now has across it: .
  3. The controlled source has its plus terminal at the bottom, next to the bottom wire, so the bottom of the resistor sits at . The voltage across the resistor from the middle node down is , so it carries downwards.
  4. KCL at the middle node. and both flow into it and the branch takes away: .
  5. . So .
  6. The same method gives the full matrix . Since , the network is not reciprocal. That is expected, because a controlled source is inside.

Trap: reading the controlled source with the opposite polarity gives , so . Taking as the current alone, and forgetting that also enters the node, gives . Both are outside the key. The code computed the matrix from the port definitions with voltage test sources, then again with current test sources and a matrix inverse, and both agree.

Where this shows up in industry

Y21 is the forward transadmittance of a device, the quantity behind small-signal amplifier models and RF device data. A network analyser measures it by shorting the output port, exactly as in this test. Y12 not equal to Y21 is the signature of an active network, which is what every amplifier is.

GATE 2025 · EC · Q.40MCQ · 2 marksTwo-port networks

Z-parameter matrix of a two-port: five 2 ohm resistors, two series, shunt, series, shunt, series (ladder)

The -parameter matrix of a two port network relates the port voltages and port currents as follows:

The -parameter matrix (with each entry in Ohms) of the network shown below is __________.
Two-port resistive ladder. Port 1 on the left (current I 1 entering the top terminal, voltage V 1 with plus at the top). Along the top wire are a 2 ohm series resistor, a node with a 2 ohm shunt resistor to the bottom wire, a 2 ohm series resistor, a second node with a 2 ohm shunt resistor to the bottom wire, and a final 2 ohm series resistor to port 2 on the right (current I 2 entering the top terminal, voltage V 2 with plus at the top).2 Ω2 Ω2 Ω2 Ω2 ΩI1 I2 +−V1 +−V2
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. and with port 2 open (). The last series resistor carries no current, so it drops no voltage and equals the voltage across the second shunt .
  2. Looking in from port 1: the second shunt is in series with the middle , giving . That is in parallel with the first shunt : . Add the first series : .
  3. With injected, the voltage at the first shunt node is . The middle and second shunt form a half-and-half divider, so and .
  4. The network is symmetric (mirror image left to right) and made of resistors only, so it is reciprocal: and .
  5. , option (A).

Trap: adding the five series resistors as one line to get (and ), which is option (C). That ignores the two shunt resistors, which carry part of the current to the bottom wire. The code built the four-node conductance matrix of the ladder and injected a test current of at each port in turn, with the other port open, reading off the port voltages. It got , matched only (A), and agreed with the product of the five cascaded ABCD matrices converted to and with a sympy series-parallel reduction.

Where this shows up in industry

Z, Y and ABCD parameters are how attenuators, matching pads and filter sections are cascaded: ABCD matrices multiply, which is the cascade check used here. In RF work the same two-port idea appears as S-parameters, measured on a network analyser and exported to simulators.

GATE 2026 · EC · Q.51MCQ · 2 marksTwo-port networks

Two-port made of a T of three 1 kOhm resistors: which set of A, B, C and D parameters is correct?

Consider the two-port network as shown in the Figure.

Which of the following options provides the correct set of values of , , and parameters?
Resistive T network between port P1 on the left and port P2 on the right. A 1 kilo-ohm resistor is in series in the top wire on each side of the centre node, and a 1 kilo-ohm resistor joins the centre node to the bottom wire1 kΩ1 kΩ1 kΩP1P2
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. ABCD (transmission) parameters are defined by and , where is taken as flowing out of port 2. Each parameter is found by opening or shorting port 2.
  2. Port 2 open (): no current in the right-hand , so equals the voltage across the shunt . Then and .
  3. Port 2 shorted (): the shunt and the right-hand are in parallel, , so . The current splits equally, so the short carries . Then and .
  4. Check: , as it must be for a reciprocal network. The set is : option (D).

Trap: option (A) has , which is with port 2 open (0.50), the inverse of . Option (B) drops the : the resistors are , not , so and carry the factors and . Option (C) doubles and , which would need a shunt resistor of and fails (). The code found , , , from the port definitions with a nodal solver: 2, 3000, 0.001, 2, with = 1.000.

Where this shows up in industry

A T of resistors is the standard attenuator pad in RF and audio gear, and ABCD matrices let you analyse a chain of such stages by multiplying their matrices. The same cascade method is used for filter chains, cables and RF line sections.

From GATE prep to a power electronics or hardware design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.