GATE Electronics (EC): Networks (nodal and mesh analysis, Thevenin and Norton, AC phasors and power, resonance, RL, RC and RLC transients, Laplace, two-port parameters), previous-year questions solved, part 2

Part 2 of 4 of the Networks: Theorems, AC, Transients hub: 7 more official GATE EC questions on AC steady state: phasors, impedance, power and resonance, each solved step by step and checked against the official answer key. Part 1 covers DC circuit analysis: nodal, mesh, superposition, Thevenin and Norton, transients and Laplace analysis of RL, RC and RLC circuits and two-port networks.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 7 of 24 questions on this page

GATE 2022 · EC · Q.38MCQ · 2 marksAC steady state: phasors, impedance, power and resonance

Locus of Z(jw) for R1 in series with R2 parallel C, semicircle from 5 kOhm to 2 kOhm: R1 and R2?

For the circuit shown, the locus of the impedance is plotted as increases from zero to infinity. The values of and are:
Series resistor R1 followed by R2 in parallel with capacitor C, with impedance Z of j omega looking in from the left. Beside it is the locus of Z as omega goes from 0 to infinity: a semicircle above the real axis from 5 kilo-ohm at omega equals 0 to 2 kilo-ohm as omega tends to infinity, with a peak of 1.5 kilo-ohm in minus Im ZR1 R2 CZ(jω)0123451.50ωω = 0ω → ∞Re(Z) kΩ−Im(Z) kΩ
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The impedance seen from the terminals is .
  2. At the capacitor is an open circuit, so . On the plot this is the right-hand end of the arc, . So .
  3. As the capacitor is a short circuit and it shorts out , so . That is the left-hand end, . So and .
  4. Check with the shape. The term traces a semicircle of diameter in the lower half plane (its imaginary part is negative, so the plot shows ). Its height is , which is exactly the marked on the vertical axis.
  5. So , : option (A).

Trap: reading the right end, , as one resistor alone. Option (D) takes and options (B), (C) take . But the right end is the sum. With option (D) the arc would run from to and rise to , and with option (B) it would run from to . The code swept for all four pairs and compared the end points and the peak with the plot: only (A) matches (, and ). It also confirmed that every point of the (A) locus lies at distance from on the real axis.

Where this shows up in industry

Impedance plots like this are how engineers read a measured component: a resistor in series with a parallel R and C is the standard model of a battery cell, a sensor or an electrode in impedance spectroscopy, and the two ends of the arc give the series and total resistance.

GATE 2022 · EC · Q.39MCQ · 2 marksAC steady state: phasors, impedance, power and resonance

V(t) = sin t, 1 Ohm in series with Z, steady current peak 1/sqrt2 A, zero rising at t = pi/4: what is Z?

Consider the circuit shown in the figure with input in volts. The sinusoidal steady state current flowing through the circuit is shown graphically (where is in seconds). The circuit element can be ________.
A sinusoidal source V of t equals sin t drives a 1 ohm resistor in series with an unknown element Z, current I of t flowing through the resistor. Beside it is the steady-state current I of t, a sine wave of amplitude 1 over root 2 ampere that crosses zero going upward at t equal to pi over 4ZI(t)1 ΩV(t) = sin(t)t = π/41/√2 A0 A−1/√2 At →I(t)
  1. (A)a capacitor of
  2. (B)an inductor of
  3. (C)a capacitor of
  4. (D)an inductor of

Answer: (B) Official key: B

  1. The source is , so . Use as the phase reference: .
  2. From the graph the current has amplitude and crosses zero going upward at . A sine that rises through zero at is . The current lags the voltage by .
  3. A lagging current means the load is inductive. In phasor form , so . Hence .
  4. For an inductor at , so : option (B). The magnitude is also right, , giving .

Trap: option (A), a capacitor, has the same impedance size, , so the amplitude is also . But the current then leads by : , which is at its peak, not at zero, when . Options (C) and (D) fail on the amplitude: gives 0.866 A and gives 0.500 A, not A. The code solved the phasor circuit for all four and also integrated the series circuit in time with a fourth-order Runge-Kutta method: for (B) the steady current at is -2.6e-05 A and rising, for (A) it is 0.707 A, the peak.

Where this shows up in industry

Telling an inductive load from a capacitive one by whether the current lags or leads the voltage is the everyday way to read a scope trace of a motor winding, a filter inductor or a decoupling capacitor, and it sets the sign of the reactive power a power-factor correction stage must cancel.

GATE 2023 · EC · Q.18MCQ · 1 markAC steady state: phasors, impedance, power and resonance

Series RLC with Q = 1000 at a centre frequency of 10^6 rad/s: which R, L and C are possible?

A series circuit has a quality factor of at a center frequency of . The possible values of , and are
  1. (A) and
  2. (B) and
  3. (C) and
  4. (D) and

Answer: (D) Official key: D

  1. Every option has the same and . The centre (resonant) frequency of a series circuit is . So all four options already give the stated centre frequency, and alone decides .
  2. For a series circuit, . Put in the numbers: , so with in ohms.
  3. For we need : option (D).

Trap: the four options give for , so picking an option with a larger gives a much lower (for example (C) gives , a ten times wider band). The code swept the series impedance over frequency for each option and measured as the centre frequency over the half-power bandwidth: 25, 25, 100 and 1000, and the peak was at in all four.

Where this shows up in industry

Q of a series LC branch sets how sharp a tuned circuit is, from RF matching networks to wireless-charging coils. In a real coil the resistance is the winding loss, so a Q of 1000 means an ohmic loss of one thousandth of the reactance.

GATE 2025 · EC · Q.20MCQ · 1 markAC steady state: phasors, impedance, power and resonance

Parallel C, L, R with admittances j0.25, -j0.1 and 0.2 S across a 1 volt at 90 degrees source: branch currents?

Let , , and be the currents flowing through the capacitor, inductor, and resistor, respectively, in the circuit given below. The AC admittances are given in Siemens (S).

Which one of the following is TRUE?
Parallel circuit driven by a source of 1 at angle 90 degrees volts, plus at the top. Three branches hang across the source, each with its current arrow pointing down: a capacitor of admittance j0.25 siemens (current i C), an inductor of admittance minus j0.1 siemens (current i L) and a resistor of admittance 0.2 siemens (current i R).+−1∠90° ViC iL iR j0.25 S−j0.1 S0.2 S
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The three branches are in parallel, so each has the full source voltage across it. With the current arrows pointing down, each current is the branch admittance times : .
  2. Capacitor: .
  3. Inductor: .
  4. Resistor: .
  5. These three together are option (A). Check on the phases: the resistor current is in phase with the voltage (), the capacitor current leads it by and the inductor current lags it by .

Trap: reading the given numbers as impedances, so that . That gives , and A, the magnitudes in (B) and (D), because , and . The problem states admittances in siemens, and current is admittance times voltage, so the magnitudes must be , and . The code computed with complex numbers and matched only (A). It then simulated the steady state at in the time domain, with , and (which have exactly these admittances), using , and , and fitted the phasors by projection. They agreed with (A) within . Reading the values as impedances gives , and , which is none of the four options.

Where this shows up in industry

Admittance is the natural unit for parallel branches because they simply add, which is how a decoupling network of capacitors in parallel with a regulator output is analysed at each frequency. The phase relations used here (capacitor current leads, inductor current lags) decide whether a parallel RLC load looks capacitive or inductive to the source.

GATE 2025 · EC · Q.39MCQ · 2 marksAC steady state: phasors, impedance, power and resonance

Voltmeter reads 25 V rms and ammeter 5 A rms across 5 ohm, C and 1 H in series at 200 rad/s: find C

In the circuit below, is an ideal AC voltmeter and is an ideal AC ammeter. The source voltage (in Volts) is .

What should be the value of the variable capacitor such that the RMS readings on and are and , respectively?
A source v s of t, plus at the top, drives a box labelled linear time invariant circuit. At the box output, an ideal voltmeter M 1 (plus at the top) sits across the output terminals. In series with the top output wire is an ideal ammeter M 2, then a 5 ohm resistor, a variable capacitor C and a 1 henry inductor, returning to the bottom wire.+−vs (t)LinearTimeInvariantCircuitM1 +−M2 5 ΩC1 H
  1. (A)
  2. (B)
  3. (C)
  4. (D)Insufficient information to find

Answer: (A) Official key: A

  1. The voltmeter is across the output terminals of the box, which are also the terminals of the series branch. The ammeter carries the branch current. So the two readings are the RMS voltage and RMS current of the same branch, and their ratio is the magnitude of the branch impedance: .
  2. At the branch impedance is , with .
  3. forces . The branch is at series resonance and looks purely resistive.
  4. means , so , option (A).
  5. The box and the source do not matter. Whatever the box is, the ratio of the two readings is the branch impedance alone, so the information is sufficient.

Trap 1: option (D). It is tempting because the box is unknown, but the meters sit on the branch, not on the box input. Trap 2: using the source RMS value in place of the voltmeter reading. That gives , and or , neither of which is an option. The code scanned over capacitor values from to and found the single value (the other options give of about and ), and drew random Thevenin sources and impedances for the box to confirm the voltmeter to ammeter ratio always equals . The wrong-source readings were computed and checked to match no option.

Where this shows up in industry

Series resonance of a capacitor with a parasitic inductance is why a decoupling capacitor stops helping above its self-resonant frequency: at resonance only its small series resistance is left, and above it the part behaves as an inductor. The same voltmeter-and-ammeter ratio is how impedance is read in practice on a bench.

GATE 2026 · EC · Q.31NAT · 1 markAC steady state: phasors, impedance, power and resonance

1 uF and 2.2 mH in parallel with a 1 kOhm load, source 12 sin(wt): average load power at resonance, in mW?

Consider the circuit shown in the Figure, where the input is in Volt.

The average power (in mW) dissipated in the load resistance of at the resonant frequency is __. (rounded off to two decimal places)
Parallel circuit driven by a sinusoidal source v_i(t) = 12 sin(omega t) volt. Across the source, three branches in parallel: a 1 microfarad capacitor, a 2.2 millihenry inductor and a 1 kilo-ohm load resistorvi (t)1 µF2.2 mH1 kΩvi (t) = 12 sin(ωt)

Answer: Official key: 71.50 to 72.50

  1. The source is ideal, so the voltage across all three parallel branches is the source voltage itself, with peak value . The capacitor and inductor cannot change this voltage.
  2. Resonance is where the parallel and susceptances cancel: . The two branches together take no current from the source, and only the resistor draws current.
  3. The is a peak value, so the average power in the resistor is .
  4. Because the source is ideal, the load power is at every frequency, not only at resonance. Resonance matters for the current the source must supply, which is smallest there.

Trap: using as if it were an rms value gives , twice the right answer and outside the official range 71.50 to 72.50. The code checked that is smallest at 21320 rad/s, that the and admittances cancel there, and averaged over one period in time: 72.00 mW at resonance and 72.00 mW at .

Where this shows up in industry

A parallel LC tank across a source is the basic tuned circuit in RF oscillators and matching networks. A real source has an output resistance, and then the tank voltage, and so the load power, does peak at resonance, which is what makes it a band-pass selector.

GATE 2026 · EC · Q.39MCQ · 2 marksAC steady state: phasors, impedance, power and resonance

R_C-C and R_L-L branches in parallel, L = 1 uH, C = 1 uF, theta1 + theta2 = 90 deg at 159.15 kHz: R_C x R_L?

In the given circuit, and . The phasor diagram for and is also shown. Assume that the phase () is at a frequency of .

Among the following options, what is the nearest integer value of ?
Two branches in parallel across a voltage V. Branch one is a resistor R_C in series with a capacitor C with current I_C downward. Branch two is a resistor R_L in series with an inductor L with current I_L downward. Phasor diagram: I_C leads the dashed V axis by angle theta 1 and I_L lags it by angle theta 2+V−IC RC CIL RL LVIC IL θ1θ2
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Take the voltage as the reference. Capacitor branch: leads by with . Inductor branch: lags by with .
  2. At , . So and (the code gives 1.0000 and 1.0000).
  3. means , that is . So and .
  4. . The frequency cancels out. So : option (B).

Trap: adding the reactances instead of multiplying them gives , option (C). Option (A) would need both angles to be (ideal reactive branches), but then : the code gives 180 degrees for . The code computed both phasor currents with complex arithmetic and scanned resistor pairs with product (the closest non-zero value to option A's ), , and for five values of : the angle sum is only for the product . A bisection on gave the product 1.000000, and the same product at and (1.000000, 1.000000).

Where this shows up in industry

Every real capacitor has an equivalent series resistance and every real inductor a winding resistance, so a decoupling capacitor in parallel with an inductive path is exactly this pair of branches. With both resistances equal to the pair is a purely resistive impedance at all frequencies, the constant-resistance idea used in Zobel and equaliser networks.

From GATE prep to a power electronics or hardware design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.