GATE Electronics (EC): Networks (nodal and mesh analysis, Thevenin and Norton, AC phasors and power, resonance, RL, RC and RLC transients, Laplace, two-port parameters), previous-year questions solved, part 3

Part 3 of 4 of the Networks: Theorems, AC, Transients hub: 5 more official GATE EC questions on transients and Laplace analysis of RL, RC and RLC circuits, each solved step by step and checked against the official answer key. Part 1 covers DC circuit analysis: nodal, mesh, superposition, Thevenin and Norton, AC steady state: phasors, impedance, power and resonance and two-port networks.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 5 of 24 questions on this page

GATE 2022 · EC · Q.51MSQ · 2 marksTransients and Laplace analysis of RL, RC and RLC circuits

RC low-pass as de-emphasis for pre-emphasis 1 + jw/w0 with w0 = 10^4 rad/s: which (R, C) pairs work?

Consider an FM broadcast that employs the pre-emphasis filter with frequency response , where . For the network shown in the figure to act as a corresponding de-emphasis filter, the appropriate pair(s) of values is/are ________.
RC network. The input voltage, plus on top, is applied to a series resistor R. The other end of R is the output, plus on top, and a capacitor C connects the output node to the bottom wire shared by input and output+−inputRC+−output
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. A de-emphasis filter undoes the pre-emphasis, so the product of the two responses must be at every frequency: .
  2. The network is a voltage divider with nothing connected at the output. KCL at the output node gives , so .
  3. Matching the two forms needs .
  4. Check the pairs. (A) : yes. (B) : no. (C) : no. (D) : no.
  5. Only (A) is correct. Only the product matters, not the two values separately.

Trap: option (D) looks tidy but is ten times too large: its corner is at , not . At the cascade of pre-emphasis and this filter has magnitude 0.141 instead of . The code solved the network by KCL for all four pairs and multiplied by over to : only (A) gives a flat gain of exactly . (B) and (C) have the same and both fail.

Where this shows up in industry

Pre-emphasis and de-emphasis pairs are used in FM broadcast (time constants of 50 or 75 microseconds), in audio recording and in serial links: boosting high frequencies before the noisy channel and cutting them after it gives a better signal to noise ratio at the receiver. The de-emphasis side is just a first-order RC low-pass.

GATE 2023 · EC · Q.35NAT · 1 markTransients and Laplace analysis of RL, RC and RLC circuits

2 V source, 1 Ohm, then 2 Ohm in parallel with 1 H; switch opens at t = 0: maximum |V_R|?

In the circuit shown below, switch was closed for a long time. If the switch is opened at , the maximum magnitude of the voltage , in volts, is _________ (rounded off to the nearest integer).
Series loop: a 2 volt source Vs, a switch S, a 1 ohm resistor, and then a 2 ohm resistor in parallel with a 1 henry inductor, back to the source. The voltage V_R is taken across the 2 ohm resistor with plus on the left. The switch S is closed for a long time and is opened at t equal to 0+−Vs = 2 VS1 Ω1 H2 Ω+VR−

Answer: Official key: 04 to 04

  1. Before the circuit is in DC steady state. The inductor is a short circuit, so it bypasses the resistor and . The source current is , and all of it goes through the inductor: (left to right).
  2. An inductor current cannot jump, so . When the switch opens, the source branch is cut off. The inductor and the resistor now form a closed loop on their own.
  3. The inductor still pushes left to right, so the current returns through the resistor from right to left. With defined on the left, .
  4. The loop is a source-free circuit with time constant , so for . It is largest at , so the maximum magnitude is .

Trap: treating the inductor as an open circuit before the switch opens gives . That is wrong: in DC steady state the inductor shorts the . Also remember before , so the voltage jumps to . The code integrated in small steps from : the largest is 4.00 V, matching .

Where this shows up in industry

This is the freewheel problem of switching inductive loads: when a switch opens, the inductor current keeps flowing and sets a voltage across whatever it flows into. Relay and motor drivers add a diode or snubber for exactly this reason.

GATE 2023 · EC · Q.44MCQ · 2 marksTransients and Laplace analysis of RL, RC and RLC circuits

1 A source, 0.01 F, 100 Ohm + 1 H, 25 Ohm; S1 opens and S2 closes at t = 0: i_c(0+)?

The switch was closed and was open for a long time. At , switch is opened and is closed, simultaneously. The value of , in amperes, is
A 1 ampere current source, pointing up, feeds the top rail through switch S1. Across the rails are a 0.01 farad capacitor with current i_c flowing down through it, a 100 ohm resistor in series with a 1 henry inductor, and a 25 ohm resistor. Switch S2 connects the top rail to the junction between the 100 ohm resistor and the inductor, shorting the 100 ohm resistor when closed. S1 is closed and S2 is open for a long time. At t equal to 0, S1 opens and S2 closes simultaneously1 AS10.01 Fic100 Ω1 HS225 Ω
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Before (DC steady state) the capacitor is an open circuit and the inductor is a short. The source feeds the (in series with the shorted inductor) in parallel with the : , so the capacitor voltage is .
  2. The inductor current is , downwards.
  3. At the capacitor voltage and the inductor current cannot jump: and . opens, so the source is gone. closes across the resistor, so that resistor is shorted out and the inductor is connected straight to the top rail.
  4. The top node now has three branches to ground and no source: the capacitor ( downwards), the resistor, and the inductor. The resistor carries downwards and the inductor carries downwards. KCL at the top node: .
  5. So : option (B). The capacitor discharges, and the current actually flows upward through it.

Trap: option (D), , is only the current and forgets the inductor. Option (C), , is only the inductor current, and option (A), , has the right size but the wrong sign: is defined downwards and the capacitor is the only source of current for the other two branches. The code found the DC state ( V, A) and integrated the state equations and from there: and the response decays. Only (B) matches.

Where this shows up in industry

Initial conditions of a capacitor and inductor right after a switch event are checked this way in power supplies and hot-swap circuits. The capacitor voltage and inductor current carry over, and the instant current is whatever KCL then demands.

GATE 2024 · EC · Q.32NAT · 1 markTransients and Laplace analysis of RL, RC and RLC circuits

RL circuit, 3 H inductor, 5 A source, 2 Ohm and two 4 Ohm resistors: time constant for t > 0 in seconds?

In the circuit given below, the switch was kept open for a sufficiently long time and is closed at time . The time constant (in seconds) of the circuit for is _______.
RL circuit with a switch. A 5 A current source pointing up on the left is in parallel with a 2 ohm resistor. A 3 henry inductor runs along the top rail to a node with a 4 ohm resistor to the bottom rail. Further right, a switch S that closes at t equals 0 connects the top rail to a second 4 ohm resistor to the bottom rail3 H5 A2 Ω4 Ωt = 0S4 Ω

Answer: Official key: 0.75 to 0.75

  1. There is one energy-storage element, the inductor, so the circuit is first order with . Here is the resistance seen by the inductor for with the independent source switched off. The initial condition does not affect .
  2. Switch off the source: a current source becomes an open circuit. Looking from the inductor to the left, only the resistor is left: .
  3. Looking to the right, the switch is closed, so the two resistors are in parallel: .
  4. The inductor sees these two in series: .
  5. .

Trap: using only the parallel pair, , gives . Using the circuit before the switch closes, , gives 0.5 s. Multiplying instead of dividing gives 12 s. All three are outside the key. The code simulated the whole circuit after closing, from to the final , with RK4 and a nodal solve at every step. The current covers of the way at .

Where this shows up in industry

The L/R time constant sets how fast current builds in a relay coil, solenoid or motor winding when a switch closes. It is why a driver with more series resistance gives a faster current rise, and why the coil current cannot jump.

GATE 2026 · EC · Q.23MCQ · 1 markTransients and Laplace analysis of RL, RC and RLC circuits

Capacitor equation C dV/dt = I(t) - m(t), I(t) = q delta(t), V(0-) = V0: equivalent representation?

The relation between the input current () and the output voltage () of a circuit is governed by the equation: . The circuit is excited by , where is a real valued constant. at is .

Which of the following is an equivalent representation of the above case?
  1. (A), with
  2. (B), with
  3. (C), with
  4. (D), with

Answer: (A) Official key: A

  1. The equation is a capacitor driven by a current source , with a second current drawn away from it. The impulse acts only at .
  2. Integrate both sides over the instant of the impulse, from to : . The last integral is zero because is finite, so over a zero-width interval it adds nothing.
  3. So the impulse instantly adds charge to the capacitor, and the voltage jumps by : .
  4. For the impulse is gone, , and the equation is . The jump is carried by its starting value, which is (option A writes this starting value as the value at , meaning the value the impulse-free equation starts from).
  5. Equivalent representation: with start value , option (A).

Trap: options (B) and (C) add to the start value. That would be right only if itself contained an impulse. A finite cannot move in zero time. Option (D) forgets the charge already on the capacitor, . The code applied a very narrow pulse of area ( wide) with , , and : jumped by 1.5000, equal to . It then compared = 1.6683 with each option's reference: only (A) gives 1.6683; (B) gives 3.6683, (C) 0.6683, (D) 0.1683.

Where this shows up in industry

A short current spike dumping charge on a capacitor steps its voltage by . This is the model for charge injection in a sample-and-hold, for an ESD or switching spike on a decoupling capacitor, and for a charge-pump pulse on a loop-filter capacitor.

From GATE prep to a power electronics or hardware design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.