GATE Electronics (EC): Analog Circuits (diode clippers, clampers and rectifiers, BJT and MOSFET amplifiers, current mirrors, differential pairs, op-amps, filters and oscillators), previous-year questions solved, part 4
Part 4 of 4 of the Analog Circuits: Diodes, BJT, Op-amps hub: 6 more official GATE EC questions on op-amp filters, Schmitt triggers and oscillators, each solved step by step and checked against the official answer key. Part 1 covers diode circuits: clippers, clampers, rectifiers and Zener regulators, BJT and MOSFET amplifiers: biasing, small signal and frequency response, current mirrors and differential amplifiers and op-amp amplifiers: inverting, non-inverting and summing circuits.
Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 6 of 32 questions on this page
Ideal op-amp, 1 uF in series with 1 kOhm in, 2 kOhm feedback: filter type and 3 dB frequency?
- (A)The circuit is a low pass filter.
- (B)The circuit is a high pass filter.
- (C)The frequency is .
- (D)The frequency is .
Answer: (B) and (C) Official key: B,C
- The inverting input is a virtual ground, so the gain is the ratio of the feedback impedance to the input impedance: with , , .
- At very low frequency the capacitor is an open circuit and the gain goes to . At high frequency it is a short and the gain tends to . Low frequencies are blocked, so it is a high pass filter: (B) is true and (A) is false.
- The corner is where , so . There , which is below the maximum of : (C) is true. The code found the point on the full magnitude curve at .
- The feedback resistor sets the passband gain only. It does not move the corner, because the pole comes from the input network seen by the virtual ground.
Trap: option (D) uses the total resistance, , as if the capacitor charged through both resistors. The code evaluated the gain there: it is 0.316 of the maximum, not , so it is not the point. Option (A) is wrong because the gain is at low frequency. Checked from the transfer function: only (B) and (C) are true.
A capacitor in series with the input resistor of an inverting stage is how audio mixers, microphone preamps and sensor front ends block DC offset while passing the signal. The corner at 1/(2 pi R C) is chosen so that the lowest wanted frequency passes.
Ideal op-amp relaxation oscillator, supplies +15 V and -12 V, ideal diodes: max minus min of V_c?
- (A)
- (B)
- (C)
- (D)
Answer: (C) Official key: C
- The op-amp has positive feedback through the resistor chain, so it is a comparator. Its output sits at a rail, or , and flips when the capacitor voltage (on the input) crosses the voltage at the input. The capacitor charges through the feedback towards the output rail.
- Output at : current flows from the output down the chain. The upper diode is reverse biased, so its resistor stays in the path. The lower diode (anode on the input side) conducts and shorts the second . The input sees a divider of over : .
- Output at : current flows the other way. Now the upper diode conducts and shorts its , and the lower diode is blocked. The input sees over : .
- So rises towards until it reaches , the output flips to , and falls until it reaches , where it flips back. The extremes of are and .
- Difference : option (C).
Trap: reading the diodes the wrong way round swaps the thresholds to and , so the swing is , option (D). Option (B), , is the output swing , which the capacitor never reaches. The code solved the diode network for every on/off state and simulated the oscillator in time: the swing is 13.00 V with the drawn diodes and 14.00 V with them reversed.
This is the classic op-amp astable multivibrator. It makes a square wave from one op-amp, one capacitor and a few resistors, which is how simple clock, LED-flasher and buzzer-driver circuits are built. Steering diodes set different thresholds and so different on and off times.
Ideal op-amp, 1 kOhm RC low-pass on the + input, Bode plot flat at 12 dB and 9 dB at log w = 3: R and C?
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- No current enters the input of an ideal op-amp, so the RC network is a plain low-pass filter ahead of a non-inverting amplifier: .
- Low-frequency gain from the plot is . So and . This rules out (B), (gain , ), and (C), (gain , ).
- The plot has fallen by to at , that is . That is the corner, so and .
- The pair is : option (A).
Trap: option (D) has the right gain but , which puts the corner at and the gain at down to 5.05 dB, not . We evaluated all four pairs against three points read off the plot ( at , at , about at ): only (A) matches (it gives 9.03 dB at ). (B) gives 6.02 dB and (C) 13.98 dB at low frequency.
An RC low-pass in front of a non-inverting amplifier is a standard way to set both gain and bandwidth in a sensor or ADC front end. It limits noise and out-of-band signals before gain is applied, and the corner follows the sampling rate.
Op-amp Schmitt trigger (10 k, 100 k) driving a 1 mH, 1 k op-amp integrator, +-10 V rails: true statement?
- (A) is delayed by relative to , and is a triangular waveform.
- (B) is not delayed relative to , and is a trapezoidal waveform.
- (C) is not delayed relative to , and is a triangular waveform.
- (D) is delayed by relative to , and is a trapezoidal waveform.
Answer: (D) Official key: D
- OPA1 has no path from its output to its inverting input. The output goes to the non-inverting input through : positive feedback. It is a Schmitt trigger and .
- It switches when . With no input current, , so the threshold is . For it flips high at , and for it flips low at .
- The triangle goes from to in , a slope of . It reaches exactly after its zero crossing, and is reached after the falling zero crossing. So is a square wave delayed by .
- OPA2 is an integrator: the inductor current is and with . A input ramps at .
- Over a half period an unlimited ramp would swing , far more than the limits. So ramps for about a microsecond and then sits on a rail: a trapezoidal wave. Option (D).
Trap: reading OPA1 as a plain comparator gives no delay (options B and C). A threshold of would give (option A) but the divider sets . We simulated both stages in steps (inductor current as the state, rail clamping on OPA2): the edge of follows by 1.00 and sits on a rail for 50% of the period, with ramps of 10.0 V/s. That is a trapezoid.
A Schmitt trigger followed by an integrator is the textbook function-generator loop that turns a square wave into a triangle, and hysteresis from positive feedback is how comparators on sensor inputs ignore noise. The saturation of the integrator shows why a real integrator needs a reset or a DC feedback path.
Ideal op-amp with R and R1 at the inverting input and a C-R-R-C network to the + input: R1 and frequency?
- (A) and
- (B) and
- (C) and
- (D) and
Answer: (B) Official key: B
- The amplifier is non-inverting: the gain is , with from the inverting input to ground and in feedback.
- The positive-feedback network (output, series , node with shunt , series , node with shunt , to the input) has the transfer function, with : .
- At , that is : . It is real and positive, so the phase is zero. This is the Wien-bridge condition.
- Barkhausen: with zero phase gives , so and , at : option (B).
Trap: with (option A) are the numbers of the three-section RC phase-shift oscillator. We confirmed that a three-section ladder gives at , so that is where those numbers come from. They do not fit this circuit: its loop gain at those values is 8.27, not . The code evaluated the loop gain of this network for all four options and only (B) gives exactly at zero phase.
The Wien-bridge oscillator is the classic low-distortion audio sine source, and the gain of exactly 3 is held in practice by a small lamp or a diode network in the feedback arm. Without that control the amplitude either dies away or hits the supply rails.
Op-amp band-pass filter with R, 10C input and 2R parallel 0.1C feedback: upper -3 dB for 1 MHz lower?
The upper frequency (in MHz, rounded off to the nearest integer) is __________.
Answer: Official key: 50 to 50
- The op-amp is inverting: with and .
- So . Mid-band gain is .
- The input network with gives the lower corner . The feedback network with gives the upper corner .
- The ratio is . With , .
Trap: reading the feedback time constant as and forgetting the factor 2 of , which gives . We evaluated with complex arithmetic and checked that the pole frequencies are in the ratio 50 and the mid-band gain is 2. Note: the two corners are only a factor 50 apart, so the exact half-power points of this transfer function are about 54 MHz for a 1 MHz lower point. The official key is 50 MHz, which is the pole-frequency (corner) answer given here.
A first-order high-pass at the input and a first-order low-pass in the feedback is the standard way to build a wide band-pass stage for audio, sensor or RF-envelope signals: it blocks DC and offset at the low end and limits noise bandwidth at the high end.