GATE Electronics (EC): Analog Circuits (diode clippers, clampers and rectifiers, BJT and MOSFET amplifiers, current mirrors, differential pairs, op-amps, filters and oscillators), previous-year questions solved, part 3

Part 3 of 4 of the Analog Circuits: Diodes, BJT, Op-amps hub: 10 more official GATE EC questions on current mirrors and differential amplifiers and op-amp amplifiers: inverting, non-inverting and summing circuits, each solved step by step and checked against the official answer key. Part 1 covers diode circuits: clippers, clampers, rectifiers and Zener regulators, BJT and MOSFET amplifiers: biasing, small signal and frequency response and op-amp filters, Schmitt triggers and oscillators.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 10 of 32 questions on this page

GATE 2023 · EC · Q.64NAT · 2 marksCurrent mirrors and differential amplifiers

1 mA mirrored through pMOS (W/L 1, 10, 7) and nMOS (W/L 10, 5) into a 1 kOhm load: find VL

In the circuit below, the voltage is ____________ V (rounded off to two decimal places).
A current mirror network. A 1 milliampere current source pulls current through a diode-connected pMOS transistor with W/L of 1 whose source is at V DD. Its gate is shared with a pMOS transistor with W/L of 10 and a pMOS transistor with W/L of 7. The W/L of 10 pMOS drain feeds a diode-connected nMOS with W/L of 10, whose gate is shared with an nMOS with W/L of 5. The W/L of 7 pMOS drain and the W/L of 5 nMOS drain meet at node V L, which connects to ground through a 1 kilo-ohm resistorVDD1 mAVL1 kΩW/L = 1W/L = 10W/L = 7W/L = 10W/L = 5

Answer: Official key: 2.00 to 2.00

  1. The pMOS with is diode-connected and carries the of the current source. Its gate voltage is shared with the pMOS devices of and , all with the same source voltage . A mirror copies current in proportion to (same , same , channel length modulation neglected).
  2. The pMOS with carries , and the pMOS with carries .
  3. The goes into the diode-connected nMOS with . Its gate is shared with the nMOS of , which copies .
  4. At the node, flows in from the pMOS and is pulled down by the nMOS. The difference flows through the load: .
  5. . This assumes both devices at stay in saturation, which the question implies by giving no supply value.

Trap: forgetting the nMOS sink and sending all into the load: . Or reading the nMOS mirror as 1:1, so it tries to pull against of supply: the load would get nothing, and the nMOS would leave saturation. Both are outside the key. We solved the whole network with the square law (Newton iteration over all five MOSFETs and the resistor) for three different supply and device sets. In each, every device was in saturation, the currents were and , and .

Where this shows up in industry

Mirrors with W/L ratios are the standard way to fan one reference current out into many bias currents across an analog chip. The nMOS-pMOS pair here is a current-subtracting node, as in the output of an OTA or the current summing at an ADC or DAC input.

GATE 2024 · EC · Q.18MCQ · 1 markCurrent mirrors and differential amplifiers

MOS pair with mirror load, output tied to the other gate, open-loop gain 40: closed-loop gain v_out/v_in?

For the closed loop amplifier circuit shown below, the magnitude of open loop low frequency small signal voltage gain is . All the transistors are biased in saturation. The current source is ideal. Neglect body effect, channel length modulation and intrinsic device capacitances. The closed loop low frequency small signal voltage gain (rounded off to three decimal places) is ____.
A differential pair with a current mirror load. Two p-channel transistors have their sources at V_DD and their gates joined together and to the drain of the left one. Two n-channel transistors have their sources joined to an ideal current source I_SS to ground. The left n-channel gate is the input V_in. The right p-channel and right n-channel drains meet at the output V_out, which is connected to the right n-channel gateVDDVoutVinISS
  1. (A)0.976
  2. (B)1.000
  3. (C)1.025
  4. (D)0.488

Answer: (A) Official key: A

  1. The two NMOS transistors form a differential pair and the PMOS pair is a current mirror load. The left gate is the non-inverting input, . The right gate is tied to , so the right gate is the inverting input and the circuit is a unity-feedback buffer.
  2. Polarity check: a rise in raises the left current, the mirror copies it to the output node, and rises. The same on the right gate lowers the right current. That is negative feedback.
  3. With open-loop gain for the difference of the two gates: .
  4. So : option (A).

Trap: taking the gain as 1 (option B) is the ideal buffer, true only for infinite . Option (C) is the inverted fraction ; a buffer with negative feedback cannot have a gain above 1. Option (D) is half the right value, 0.488. We solved a small-signal nodal model of the pair and mirror, chose the output resistance so the open-loop gain was 40.000, closed the loop and got 0.97561. The result does not depend on the mirror transconductance.

Where this shows up in industry

A differential pair with a mirror load, wired as a buffer, is the first stage of most CMOS op-amps and of the small buffers that drive reference voltages and ADC inputs. The gain error of 1/(1+A) is why designers ask for a high open-loop gain in a reference buffer.

GATE 2025 · EC · Q.43MCQ · 2 marksCurrent mirrors and differential amplifiers

MOSFET differential pair, g_m = 5 mS, 1 k loads, 2 mA tail, inputs 2.5 V plus/minus 0.01 sin wt: V3?

The identical MOSFETs and in the circuit given below are ideal and biased in the saturation region. and have a transconductance of .
The input signals (in Volts) are:


The output signal (in Volts) is __________.
A MOSFET differential pair. Two identical n-channel transistors M1 and M2 have their sources joined to a 2 milliamp current source to ground. Each drain goes to a 5 volt supply through a 1 kilohm resistor. The gate of M1 is the input V1 and the gate of M2 is V2. The drain of M1 is the output V3 and the drain of M2 is the output V4VDD = 5 V1 kΩ1 kΩV3V4V1V2M1M22 mA
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. DC: the pair is symmetric and the tail current is , so each transistor carries . The DC drop in each load is , so .
  2. AC: the inputs are equal and opposite, , a purely differential signal. The tail node does not move (virtual ground), so sees and its drain current changes by .
  3. A rising drain current lowers the drain voltage, so .
  4. , option (D).

Trap: using the whole difference as the gate swing of one transistor, which doubles the amplitude to 0.1 V and points to (B) or (C), and using the full tail current in one load, which gives a DC level of 3 V (options A and B). We simulated the large-signal square-law pair (with at , so ) over a full cycle, solving the tail node each step and checking that both transistors stay in saturation: the output had a mean of 4.000 V and a fundamental of -0.050 V, which matches only (D).

Where this shows up in industry

This is the input stage of nearly every op-amp and comparator. The differential gain is per output, and the constant tail current keeps the DC output near the middle of the supply, which sets the bias point of the next stage.

GATE 2022 · EC · Q.58NAT · 2 marksOp-amp amplifiers: inverting, non-inverting and summing circuits

Ideal op-amp, R = 1 kOhm, R and 2R ladder with two 1.6 V sources into a 2R input and 3R feedback: V0?

Consider the circuit shown with an ideal OPAMP. The output voltage is __________V (rounded off to two decimal places).
Op-amp circuit with R equal to 1 kilo-ohm. A ladder runs left to right. Leftmost node: a 2R resistor to ground and a 2R resistor to plus 1.6 volts. Then R to a node with 2R to ground, then R to a node with 2R to plus 1.6 volts, then R to a node with 2R to ground, then 2R to the inverting input. A 3R resistor connects the output back to the inverting input. The non-inverting input is grounded. Supplies plus and minus 15 volts. V_0 is the outputRRR2R2R2R+1.6 V2R2R+1.6 V2RR = 1 kΩ−++15 V−15 V3R+−V0

Answer: Official key: -0.55 to -0.45

  1. The non-inverting input is grounded, so the inverting input is a virtual ground at . The resistor into it carries a current set only by the voltage at the last ladder node, .
  2. Write KCL at the four ladder nodes (left to right; the first node has two legs, one to ground and one to ): , , , .
  3. The solution is , , , .
  4. Current into the summing node: . All of it flows through the feedback resistor, so . This is well inside the rails, so the op-amp stays linear.

Trap: forgetting that the last branch loads the ladder (using the ladder voltage with the op-amp branch removed) gives . Dropping the inversion gives . Both are outside the official range to . We solved the nodal equations with numpy and checked all three variants.

Where this shows up in industry

Resistor ladders feeding an inverting summing amplifier are the core of an R-2R digital-to-analog converter, and the same weighted-sum idea is used for audio mixing and for adding offsets in sensor signal chains.

GATE 2023 · EC · Q.39MCQ · 2 marksOp-amp amplifiers: inverting, non-inverting and summing circuits

Inverting and non-inverting op-amp stages (R1, R2) feeding a summer (R3, R4): find VOUT/VIN

The of the circuit shown below is
Three op-amps. Op-amp 1 is an inverting stage: vIN through R1 to its minus input, R2 from its output back to the minus input, plus input grounded. Op-amp 2 is a non-inverting stage: vIN drives its plus input, and its minus input goes to ground through R1 with R2 as feedback from the output. Op-amp 3 is a summer: the output of op-amp 1 and the output of op-amp 2 each go through an R3 to the minus input of op-amp 3, which has R4 as feedback and a grounded plus input. The output of op-amp 3 is vOUT−+VCC-VEE+−VCC-VEE−+VCC-VEEvINR1R2R1R2R3R3R4vOUT
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. With negative feedback each op-amp holds its two inputs at the same voltage (virtual short), so each stage can be solved alone.
  2. Top stage: through into the minus input, plus input grounded, feedback . It is an inverting amplifier: .
  3. Bottom stage: drives the plus input, and the minus input sees to ground with feedback . It is a non-inverting amplifier: .
  4. Output stage: both and reach the minus input through equal resistors , with feedback and the plus input grounded. It is an inverting summer: .
  5. The sum is . The terms cancel exactly.
  6. : option (A).

Trap: reading both first stages as inverting, which gives and a gain that depends on , so no option would fit. Another slip is dropping the minus sign of the summer and landing on (B). We solved the full circuit by nodal analysis with a finite op-amp gain of for 200 random resistor sets. The ratio matched every time (relative error below ), and stage 1 and stage 2 gains matched and . For , , , the gain is , equal to and different from the other three options. Taking both first stages as inverting gives , which matches no option.

Where this shows up in industry

Cancelling a gain term by adding an inverting and a non-inverting copy of a signal is a way to get a precise gain of one with matched resistors. Input stages of instrumentation amplifiers use the same non-inverting plus inverting pairing, and resistor matching sets the accuracy.

GATE 2025 · EC · Q.29MSQ · 1 markOp-amp amplifiers: inverting, non-inverting and summing circuits

Which statements are true for an ideal op-amp: input/output resistance, differential and common-mode gain?

Which of the following statements is/are TRUE with respect to an ideal opamp?
  1. (A)It has an infinite input resistance
  2. (B)It has an infinite output resistance
  3. (C)It has an infinite open-loop differential gain
  4. (D)It has an infinite open-loop common-mode gain

Answer: (A) and (C) Official key: A;C

  1. An ideal op-amp is a perfect voltage-controlled voltage source. It must not load the circuit that drives it, so the input resistance is infinite: (A) is true.
  2. It must deliver its voltage into any load without a drop, so the output resistance is zero, not infinite: (B) is false.
  3. The open-loop differential gain is infinite. That is what forces the two inputs to the same voltage when negative feedback is used (the virtual short): (C) is true.
  4. The common-mode gain is zero, because an ideal op-amp responds only to the difference of its inputs (CMRR is infinite). An infinite common-mode gain would make the output follow the average of the inputs: (D) is false.

Trap: (B) and (D), because \"infinite\" is easy to attach to every property. We modelled each statement as a limit of a real op-amp: with the source is not loaded, with the closed-loop gain of becomes exact, but with the loaded output collapses to zero, and with a pure common-mode input gives a huge output. Only (A) and (C) are consistent with an ideal amplifier.

Where this shows up in industry

Real op-amps are judged against these ideals: input bias current and input impedance for , output impedance for driving ADC inputs and cables, open-loop gain at the signal frequency, and CMRR in instrumentation front ends.

GATE 2026 · EC · Q.17MCQ · 1 markOp-amp amplifiers: inverting, non-inverting and summing circuits

Ideal op-amp with 1 kOhm to ground and 2 kOhm + 1 kOhm feedback: output when the switch S closes

The ideal OP-AMP circuit shown in the Figure produces output voltage when the Switch, S, is open.
Which of the options represents the output voltage when S is closed?
Ideal op-amp, non-inverting. Input Vi = 1 V on the plus input. The minus input node goes through 1 kilo-ohm to ground and through 2 kilo-ohm in series with 1 kilo-ohm to the output Vo. Switch S, drawn open, connects the junction of the 2 and 1 kilo-ohm resistors to the output, so closing it shorts the right-hand 1 kilo-ohm1 kΩ2 kΩ1 kΩS−+VoVi = 1 V
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. The input is on the plus pin and the minus pin goes to ground through , so this is a non-inverting amplifier: with .
  2. Switch open: the feedback path is . .
  3. The switch sits between the junction of the two feedback resistors and the output pin, so closing it shorts the right-hand . Only the is left in the feedback path.
  4. Switch closed: .
  5. The output falls from to . Correct option: (C).

Trap: reading the switch as shorting the resistor. Then only remains in feedback, , which is option (D). We solved the full circuit by nodal analysis with a finite-gain op-amp (gain ): open, closed, ratio . The wrong reading gives ratio .

Where this shows up in industry

A switch that bypasses part of the feedback network is how programmable-gain amplifiers in sensor front ends and instrumentation inputs change range: analog switches select resistor taps, and the gain steps by fixed ratios. The switch on-resistance adds to the feedback resistor, so designers keep the feedback resistors large against it.

GATE 2026 · EC · Q.18MCQ · 1 markOp-amp amplifiers: inverting, non-inverting and summing circuits

Op-amp with Vi = 3 V drives a BJT base, 1 kOhm in the emitter, beta = 99: find the current Io

Consider the circuit shown in the Figure with and .
Assume and for the BJT.
Which of the following options is the correct value of the current ?
Op-amp with Vi on the plus input driving the base of an NPN transistor, current Io leaving the op-amp output into the base. The collector goes through 2 kilo-ohm to VCC. The emitter goes through 1 kilo-ohm to ground and is also wired back to the op-amp minus inputVCC2 kΩ+−ViIo1 kΩ
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. The emitter is wired to the minus input, so the op-amp is a unity feedback loop around the transistor. With negative feedback and an ideal op-amp, the minus pin follows the plus pin: . The op-amp output (the base) sits at , and this does not change the answer.
  2. Emitter current: .
  3. is the current the op-amp pushes into the base, so .
  4. Region check: drops 5.94 V in the , so , above the base at . The transistor is in the active region, so holds.
  5. , option (D).

Trap: subtracting from , as in a simple bias network. That gives and , which matches no option. The feedback loop forces the emitter to itself, not . Also, and are about , a hundred times larger than , so reading as the emitter or collector current is wrong by that factor. We solved the loop with a finite-gain op-amp () and the active-region condition: .

Where this shows up in industry

This op-amp plus transistor loop is a voltage-to-current converter: the load current is set by and does not depend on or to first order. It is used as a precision current source for sensor excitation and LED or laser-diode drivers, where the op-amp removes the drift.

GATE 2026 · EC · Q.53MCQ · 2 marksOp-amp amplifiers: inverting, non-inverting and summing circuits

Ideal inverting op-amp, Vi = 2 V, 1 kOhm input and feedback, 2 kOhm output and load resistors: current Ix

A circuit using an ideal OP-AMP is shown in the Figure.
Which of the following options gives the correct value of the current ?
Ideal op-amp. Vi = 2 V through 1 kilo-ohm to the minus input; the plus input is grounded. A second 1 kilo-ohm runs from the minus input node to node X. The op-amp output goes through a 2 kilo-ohm resistor to node X, and node X has a 2 kilo-ohm resistor to ground. The current IX is marked on the 2 kilo-ohm output resistor, pointing from X toward the op-amp outputVi = 2 V1 kΩ1 kΩ−+2 kΩIX2 kΩ
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. The plus pin is grounded and the loop is closed through the feedback resistor, so the minus pin is a virtual ground at .
  2. Input current: . The op-amp input draws none, so all flows through the feedback to node .
  3. Voltage at : . The feedback is taken from , so it is that the loop regulates, not the op-amp output pin.
  4. The from to ground sees , so it carries from to ground. That is, flows up from ground into .
  5. KCL at : arrives from the feedback resistor and from the ground resistor, and both must leave through the output resistor toward the op-amp output, the direction of in the figure. , option (C).
  6. Check: the op-amp output sits at , so the op-amp must sink the current.

Trap: stopping at the feedback resistor and answering , option (A). That is only the current in the feedback path. The resistor to ground adds another at node . We solved the circuit by nodal analysis with a finite-gain op-amp (): , feedback current , .

Where this shows up in industry

A resistor in series with the op-amp output, with the feedback taken after it, is how designers isolate an op-amp from a capacitive or cable load, and the loop still holds the voltage at the load node. The op-amp must be able to supply the extra load current plus the drop across that output resistor.

GATE 2026 · EC · Q.62NAT · 2 marksOp-amp amplifiers: inverting, non-inverting and summing circuits

Ideal inverting op-amp with T feedback network, R1 = R2 = R3 = R4 = 50 kOhm: closed loop gain magnitude

Consider an ideal OP-AMP circuit as shown in the Figure.
The resistances .
The magnitude of the closed loop gain is ___.
(rounded off to two decimal places)
Ideal op-amp, inverting. Input vi goes through R1 to the minus input; the plus input is grounded. The feedback path from the minus input to the output is R2 then R3 in series, and the junction of R2 and R3 is connected to ground through R4viR1R2R3R4−+vo

Answer: Official key: 2.90 to 3.10

  1. The plus pin is grounded, so the minus pin is a virtual ground. The input current is , and it all flows into because the op-amp input draws none.
  2. Voltage at the T junction (between and ): (since ).
  3. Current through to ground: .
  4. KCL at : the current into is .
  5. .
  6. General result: . The magnitude is .

Trap: ignoring and using the plain inverting formula with as feedback: , magnitude , outside the key range. bleeds current to ground and forces the output to swing further. We solved the nodal equations with a finite-gain op-amp (): magnitude with , and when is made open.

Where this shows up in industry

A T network in the feedback path gives a large effective feedback resistance from small resistors, which keeps resistor noise and stray capacitance low in high-gain transimpedance and inverting stages. The cost is that the op-amp's own input offset voltage is amplified by a larger noise gain than the signal gain alone would suggest.

From GATE prep to a electronics hardware career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.