GATE Electronics (EC): Analog Circuits (diode clippers, clampers and rectifiers, BJT and MOSFET amplifiers, current mirrors, differential pairs, op-amps, filters and oscillators), previous-year questions solved, part 2

Part 2 of 4 of the Analog Circuits: Diodes, BJT, Op-amps hub: 9 more official GATE EC questions on BJT and MOSFET amplifiers: biasing, small signal and frequency response, each solved step by step and checked against the official answer key. Part 1 covers diode circuits: clippers, clampers, rectifiers and Zener regulators, current mirrors and differential amplifiers, op-amp amplifiers: inverting, non-inverting and summing circuits and op-amp filters, Schmitt triggers and oscillators.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 9 of 32 questions on this page

GATE 2022 · EC · Q.59NAT · 2 marksBJT and MOSFET amplifiers: biasing, small signal and frequency response

nMOS amplifier, 4 kOhm in the drain and 2 kOhm in the source, saturation: v_A / v_B?

Consider the circuit shown with an ideal long channel MOSFET (enhancement-mode, substrate is connected to the source). The transistor is appropriately biased in the saturation region with and such that it acts as a linear amplifier. is the small-signal ac input voltage. and represent the small-signal voltages at the nodes A and B, respectively. The value of is ________ (rounded off to one decimal place).
n-channel enhancement MOSFET amplifier. A plus V_DD supply feeds the drain through a 4 kilo-ohm resistor. Node A is at the drain. The source, node B, goes to ground through a 2 kilo-ohm resistor. The gate is driven by a small-signal source v_i in series with the DC bias V_GG to ground. The substrate is tied to the sourceVDD4 kΩAB2 kΩviVGG

Answer: Official key: -2.1 to -1.9

  1. An ideal long channel device in saturation has no channel-length modulation, so the small-signal drain current is just . The substrate is tied to the source, so there is no body effect.
  2. The same current flows through the drain resistor and the source resistor (no gate current).
  3. Drain node: (the current pulls the drain down). Source node: (the current lifts the source).
  4. Divide: . The value of and the bias cancel out.

Trap: dropping the sign (the drain and source move in opposite directions, so it is the ratio that is , not ), or inverting the ratio to . Both are outside the official range to . The code solved the square-law bias with a root finder at four different , and settings, checked saturation, and took finite-difference gains: the ratio was every time.

Where this shows up in industry

Source degeneration trades gain for stability: the gain is set by a resistor ratio instead of by transconductance, which moves with temperature and process. A drain and source output pair with equal and opposite swing, as here, is also the basic single-ended phase splitter.

GATE 2023 · EC · Q.21MCQ · 1 markBJT and MOSFET amplifiers: biasing, small signal and frequency response

MOS cascode driven at the source through R1, biased by V1 and V2: which controlled source is it?

In the circuit shown below, and are bias voltages. Based on input and output impedances, the circuit behaves as a
A pMOS transistor sits on top of an nMOS transistor. The pMOS source is at V DD and its gate is at bias voltage V1. The pMOS drain and the nMOS drain are joined at the output node v OUT. The nMOS gate is at bias voltage V2. The nMOS source goes through resistor R1 to the signal source v IN, whose other end is groundedVDDV1V2vOUTR1vIN
  1. (A)voltage controlled voltage source.
  2. (B)voltage controlled current source.
  3. (C)current controlled voltage source.
  4. (D)current controlled current source.

Answer: (D) Official key: D

  1. and are fixed bias voltages, so for the signal both gates are at ac ground. The pMOS (source at , gate at ac ground) is then just its output resistance : it is a current-source load.
  2. The signal enters at the source of the nMOS, through , not at its gate. Looking in: . This is a low resistance, a few hundred ohms to a few kilo-ohms.
  3. At the output node the signal sees in parallel with the nMOS drain, which is boosted by the source degeneration: . This is a high resistance, tens of kilo-ohms or more.
  4. The whole signal current of the nMOS leaves through its drain. With the output shorted, the output current equals the input current: the current gain is .
  5. Low input resistance and high output resistance with a current gain is a current controlled current source: option (D). A common-gate stage is a current buffer.

Trap: choosing (B), voltage controlled current source, because a MOSFET is \"a transistor with \". That is true for a drive at the gate, where is infinite. Here the drive is at the source. We solved the small-signal nodal equations for , , : , and . Only the pair (low input resistance, high output resistance) matches an option, and it matches (D) alone. Other and values gave the same class.

Where this shows up in industry

The same stacked pair, with the signal entering at the source, is the cascode current buffer used in telescopic and folded-cascode op-amps and in RF low-noise amplifiers. It keeps the Miller effect off the input device and gives a high output resistance for large gain.

GATE 2024 · EC · Q.17MCQ · 1 markBJT and MOSFET amplifiers: biasing, small signal and frequency response

NMOS with drain at ground, C1 from gate to source and CL from source to ground: input impedance Z_in(jw)?

In the circuit below, assume that the long channel NMOS transistor is biased in saturation. The small signal trans-conductance of the transistor is . Neglect body effect, channel length modulation and intrinsic device capacitances. The small signal input impedance is _______.
An n-channel MOSFET with its drain connected to ground and its gate connected to the input terminal. A capacitor C1 joins the gate to the source. A load capacitor C_L joins the source to ground. The input impedance Z_in(j omega) is looked at into the gate terminal on the leftC1CLZin(jω)
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Small-signal picture: the drain is at ac ground, the gate is the input and draws no current, so all the input current goes through . The source node carries to ground, to the gate and the transistor current flowing drain to source into it.
  2. KCL at the source node: . This gives .
  3. Input current: .
  4. So . With this splits into : option (A).
  5. Reading it: the two capacitors in series, plus a negative resistance . The transistor feeds energy back into the input.

Trap: dropping the transistor gives option (C), two capacitors in series. That is the answer only for . Option (B) has the right size but the wrong sign, a positive resistor; the code gives a negative real part (-156.2 ohm for , , , ). We solved the nodal equation with complex numbers for six random sets of values and checked that only (A) matches every time.

Where this shows up in industry

This is the core of a Colpitts oscillator: a transistor with two capacitors forms a negative resistance at the input, and a crystal or an LC tank with enough loss cancelled by it will oscillate. The same effect is a known stability problem for a source follower that drives a capacitive load.

GATE 2024 · EC · Q.51MCQ · 2 marksBJT and MOSFET amplifiers: biasing, small signal and frequency response

Mirror-biased common-source stage M2 with R_S, R_B, R_D and diode-connected M1: exact |v_out/v_in|?

In the circuit shown below, the transistors and are biased in saturation. Their small signal transconductances are and respectively. Neglect body effect, channel length modulation and intrinsic device capacitances. Assuming that capacitor is a short circuit for AC analysis, the exact magnitude of small signal voltage gain is ______.
A current mirror biased common-source amplifier. A current source I_ref from V_DD feeds the drain of M1, whose gate is tied to its drain and whose source is grounded. That gate and drain node connects through R_B to the gate of M2. The source v_in with resistor R_S and coupling capacitor C1 drives the gate of M2. M2 has its source grounded and its drain connected to V_DD through R_D, with the output V_out at the drainVDDIrefM1RBRSC1vinM2VDDRDVout
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. For small signals the ideal current source is an open circuit. has its gate tied to its drain, so it behaves as a resistor to ground at that node.
  2. The gate of draws no current. So and are in series to ground, and with shorted the source resistance feeds that path: .
  3. is a common-source stage with load to ac ground, with no channel length modulation: .
  4. So : option (B).

Trap: option (A) ignores the divider formed by against the bias path. Option (C) turns the divider upside down: its gain is bigger than , which a passive divider can never give. Option (D) leaves out of the path to ground. We solved the nodal equations of the whole small-signal circuit for eight random sets of component values: only (B) matched each time, and the gain was always negative (an inverting stage), as it should be.

Where this shows up in industry

Biasing a gate through a large resistor from a diode-connected mirror device is a standard way to set the operating point of an amplifier on an IC. The resistor is large so it does not load the signal, and the mirror keeps the bias current tied to a reference over temperature.

GATE 2025 · EC · Q.21MCQ · 1 markBJT and MOSFET amplifiers: biasing, small signal and frequency response

BJT small-signal circuit with R_S, r_pi, beta*i_b source and R_L: voltage gain v_o/v_s?

A simplified small-signal equivalent circuit of a BJT-based amplifier is given below.
The small-signal voltage gain (in V/V) is ___________.
Small-signal equivalent circuit of a BJT amplifier. The source v_s drives a series resistor R_S, whose far end is the top of r_pi. The base current i_b flows left to right through R_S into r_pi, and the bottom of r_pi goes to ground. A dependent current source beta times i_b points downward from the output node to ground. The output node v_o has the load resistor R_L to groundvsRSibrπβibvoRL
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The input loop has only in series with , so the base current is .
  2. The dependent source pulls out of the output node and down to ground. The same current must flow into the node from , so . The minus sign is the current direction: a positive drags the output node below ground.
  3. Combine: . This is option (A).

Trap: option (C), , which drops from the input loop as if the base were a voltage source. We solved the circuit by nodal analysis with , , , : the gain was , which matches only (A) (option (C) would give ). Options (B) and (D) fail on the sign.

Where this shows up in industry

This is the voltage-gain expression used to size a common-emitter stage against a sensor or microphone source: the source resistance divides against , so a high-impedance source loses gain before the transistor even amplifies.

GATE 2025 · EC · Q.22MCQ · 1 markBJT and MOSFET amplifiers: biasing, small signal and frequency response

Ideal BJT, beta = 100, I_B = 10 uA, 10 V supply, 5 k collector and 3 k emitter resistors: V_CE?

The ideal BJT in the circuit given below is biased in the active region with a of .
If is , then (in Volts, rounded off to two decimal places) is _______ .
An NPN transistor with a 10 V supply. A 5 kilohm resistor runs from the supply to the collector. A base resistor R_B joins the collector to the base, and the base current I_B flows into the base. The emitter has a 3 kilohm resistor to ground. The voltage V_CE is measured from collector (plus) to emitter (minus)VCC = 10 V5 kΩRBIB+−VCE3 kΩ
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. In the active region , so .
  2. The resistor carries both the collector current and the base current, because takes off the collector node. Its drop is , so .
  3. The resistor carries : .
  4. , option (C). An ideal BJT has , so the base sits at and : the active-region assumption holds.

Trap: stopping at one node voltage. is option (A) and is option (B), but is their difference. We solved both node equations and checked these two values against the options. We also computed the case that leaves out of the drop and : it gives 2.00 V, which is no option. The value of is not needed: it only sets (here it would be about ).

Where this shows up in industry

Feeding the base from the collector through is the classic collector-feedback bias: if rises, falls and the base current is pulled back down, which stabilises the bias point in discrete amplifiers.

GATE 2025 · EC · Q.30MSQ · 1 markBJT and MOSFET amplifiers: biasing, small signal and frequency response

Ideal MOSFET single-stage amplifiers with finite load: input resistance and phase of CG, CS and CD stages

Which of the following statements is/are TRUE with respect to ideal MOSFET-based DC-coupled single-stage amplifiers having finite load resistors?
  1. (A)The common-gate amplifier has an infinite input resistance
  2. (B)The common-source amplifier has an infinite input resistance
  3. (C)The input and output voltages of the common-source amplifier are in phase
  4. (D)The input and output voltages of the common-drain amplifier are in phase

Answer: (B) and (D) Official key: B;D

  1. An ideal MOSFET draws no gate current. In the common-source and common-drain stages the signal enters at the gate, so the input resistance is infinite: (B) is true.
  2. In the common-gate stage the signal enters at the source. The input current is , so , a finite value: (A) is false.
  3. The common-source gain is , negative: the output is inverted, 180 degrees out of phase. (C) is false.
  4. The common-drain (source follower) gain is , positive and below 1: the output follows the input in phase. (D) is true.

Trap: (A) and (C). The common-gate input is the low-resistance one, and the common-source stage is the inverting one. We solved the small-signal circuits with and a load: common-gate , common-source gain , common-drain gain . Only (B) and (D) are true.

Where this shows up in industry

This is why a source follower is used as a buffer in front of an ADC or a long trace, why a common-source stage is the usual gain stage (inverting, very high input resistance), and why a common-gate stage is chosen when a low input resistance is wanted, for example the cascode transistor of a high-speed amplifier.

GATE 2025 · EC · Q.47MCQ · 2 marksBJT and MOSFET amplifiers: biasing, small signal and frequency response

Two PNP transistors and a 5 V Zener from 20 V: R1 and R2 for I_Z = 25 mA and I_L = 12 mA?

In the circuit shown, the identical transistors and are biased in the active region with . The Zener diode is in the breakdown region with and .
If and , then the values of and (in k, rounded off to one decimal place) are ______, respectively.
A Zener and PNP bias network from a 20 V rail. Transistor Q2 is a PNP with its emitter at 20 V and its base tied to its collector. Its collector feeds a Zener diode (cathode at the top, breakdown current I_Z downward) whose anode node connects to resistor R1 to ground and to the base of PNP transistor Q1. Q1 has its emitter at the end of resistor R2 from 20 V (emitter current I_E downward) and its collector feeding load R_L to ground (load current I_L). V_EB2 and V_EB1 are the emitter-base voltages, and I_B is the base current of Q1 flowing out of its base toward the Zener node20 V+VEB2−Q2IZ+VZR1R2IE+VEB1−Q1IBRLIL
  1. (A) and
  2. (B) and
  3. (C) and
  4. (D) and

Answer: (A) Official key: A

  1. has its base tied to its collector, so it acts as a diode. Its emitter is at and its collector is lower. The Zener then drops , so the node under the Zener (also the base of ) is at .
  2. carries the load current as its collector current: . So and .
  3. The base current leaves the base and joins the Zener current at the node. carries : .
  4. The emitter of is above its base: . carries : .
  5. Answer: , , option (A).

Trap: a slip of a factor of 10 in the units. Volts divided by milliamps gives kilo-ohms, so , not 5.7. Option (D) is exactly 10 times option (A), which we checked. We recomputed with left out (, ): the rounded answer is the same and , so the base current does not decide the option. The load resistor is not given: it only needs to keep in the active region.

Where this shows up in industry

A Zener (or a diode string) plus a transistor makes a simple regulated current source or pass element: the Zener fixes the base voltage, the emitter resistor sets the current, and the load current barely depends on the load. It is a standard LED driver and low-power regulator stage.

GATE 2026 · EC · Q.50MCQ · 2 marksBJT and MOSFET amplifiers: biasing, small signal and frequency response

BJT common-emitter stage, 500 ohm unbypassed in the emitter, two input tones: best approximation of Vo(t)

A small signal source, is applied to a BJT circuit as shown in the Figure.
Assume zero source resistance, , , Early voltage and Thermal voltage . Effect of internal parasitic capacitances of the BJT may be neglected.
Which expression is the best approximation of the output voltage ?
Common-emitter BJT amplifier powered from plus 12 volts. Base bias divider 100 kilo-ohm to the supply and 25 kilo-ohm to ground. Input Vi(t) enters the base through a 100 nanofarad capacitor. Collector load 5 kilo-ohm, output Vo(t) taken from the collector through a 100 nanofarad capacitor. The emitter has 500 ohm in series with 1 kilo-ohm to ground, and a 10 microfarad capacitor across only the 1 kilo-ohm+12 V100 kΩ25 kΩ5 kΩVo(t)100 nF100 nFVi(t)500 Ω1 kΩ10 µF
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. DC bias first. Base divider: , . , so .
  2. , well above : active region, so the small signal model applies.
  3. Small signal parameters: , , .
  4. The two tones are at and . The capacitor is or less at these frequencies, so it shorts the for both tones. The has no capacitor across it, so it stays in the emitter path. The coupling capacitors have corner frequencies far below and pass both tones. With the BJT capacitances neglected, there is no high-frequency pole.
  5. Gain with an unbypassed emitter resistor : , and the finite trims it a little.
  6. The official is the textbook shortcut with : , , then divided by , which gives . Option (C) is that same without the division.
  7. The gain is the same for both tones, with the same sign.
  8. . The nearest option, and the one with the right sign for both tones, is (A) . The code's full network solution gives at and at .

Trap: treating the whole emitter as bypassed, which gives , close to option (C) . Only the is bypassed. The degeneration cuts the gain by about . Options (B) and (D) change the sign of the second tone, which would need a phase shift at that this circuit does not have once parasitic capacitances are ignored. We solved the complete complex nodal network (all four capacitors and the hybrid-pi model with ) at both frequencies and checked the gain is the same real negative number at both: the options are matched against the pair of gains.

Where this shows up in industry

Leaving part of the emitter resistor unbypassed is the standard way to trade gain for linearity and stable gain in discrete BJT amplifier stages: the gain is set mostly by rather than by the temperature-dependent . The bypass capacitor on the remaining resistor keeps the DC bias stable without losing all the AC gain.

From GATE prep to a electronics hardware career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.