Power Electronics Introduction to DC AC Power Inverters
Notes written by Skill-Lync from the recording · Updated 17 Nov 2026
What this workshop covers
This DC-AC inverter workshop shows how a full-bridge inverter turns DC into AC and compares bipolar and unipolar sinusoidal PWM in a PLECS simulation. Recorded by Skill-Lync in March 2021, part 1 starts with AC and DC sources and loads, the four conversion types, the switches and passives inside a converter, and where inverters are used: variable frequency drives, wind, EVs, grid-tied solar and solar water pumps. It then builds a square wave from three states (+Vdc, 0, -Vdc), turns the idea into an IGBT full bridge and extends it to a three-phase inverter.
Part 2 walks through the four switching modes of the full bridge, sine-triangle PWM, the amplitude and frequency modulation indices, and the gate logic for bipolar and unipolar schemes. A PLECS model of a solar-style DC source feeding a single-phase grid compares the two on voltage and current THD. It ends with the hardware path (gate drivers, heat sinks, PCB, DSP and FPGA controllers, hardware-in-the-loop) and job roles.
It suits electrical students who know basic circuits. Three-phase modulation, filter design equations and closed-loop control are not covered. The page description mentions AC-DC converters, but the session is about DC-AC. Unlike the broader May 2020 Introduction to Power Electronics workshop, this one stays on inverter switching and modulation.
Chapters
Part 1
- 0:00 Agenda: DC-AC inverter basics, uses and tools
- 1:04 AC and DC sources, loads and power factor
- 3:43 What a power electronic converter does
- 5:41 Switches and passives: IGBT, MOSFET, SiC, ferrite
- 8:46 Four conversion types and where inverters fit
- 11:17 Inverter uses: drives, wind, EVs, solar pumps
- 13:51 Making a square wave from +Vdc, 0 and -Vdc
- 16:00 From two-pole switches to an IGBT full bridge
- 19:08 Three-phase inverter, harmonics and low-pass filter
Part 2
- 0:00 Four switching modes of the full bridge
- 1:38 PWM: sine reference, triangle carrier, ma and mf
- 4:57 Bipolar PWM with Q1-Q4 and Q2-Q3 pairs
- 6:58 Unipolar PWM and its harmonic spectrum
- 10:22 Simulation tools: MATLAB, PSIM, PLECS, LTspice
- 11:24 PLECS demo: bipolar vs unipolar THD
- 14:51 Hardware: gate drivers, heat sink and PCB tools
- 16:59 DSP and FPGA controllers, hardware-in-the-loop
- 21:02 Job roles in power converter design
Key points from the session
- An inverter needs three output states: +Vdc (load connected directly), -Vdc (load reversed) and zero (load shorted). In the full bridge, Q1 and Q4 give +Vdc, Q2 and Q3 give -Vdc, and the zero state comes from current freewheeling through an anti-parallel diode, because the load inductance keeps the current flowing.
- Each switch must conduct in both directions and block the full DC-link voltage, which is why an IGBT or MOSFET with an anti-parallel diode is used. The instructor's rule of thumb: IGBTs for high power (he shows a 4.5 kV, 600 A part), MOSFETs for low power, SiC MOSFETs when you need high switching frequency.
- In sinusoidal PWM a sine modulating wave is compared with a triangular carrier and the switch turns on when the sine is higher. The carrier's amplitude and frequency are held fixed; changing the amplitude modulation index (sine peak over carrier peak) changes output voltage, and changing the sine frequency changes output frequency.
- Bipolar PWM switches Q1-Q4 and Q2-Q3 as pairs, so the output jumps between +Vdc and -Vdc and harmonics appear at every multiple of the frequency modulation index mf. Unipolar PWM drives each leg as a complementary pair (a NOT gate), the output steps between 0 and +Vdc or 0 and -Vdc, and the components at mf and 3mf disappear, leaving 2mf and 4mf.
- The PLECS demo uses a 400 V DC input, a 320 V peak output and 50 Hz. Measured before the filter, voltage THD is 1.79 with bipolar PWM and 0.879 with unipolar, and current THD is 0.284 with bipolar and lower again with unipolar, so the instructor recommends unipolar for grid-connected inverters.
- A square wave is the fundamental plus harmonics (Fourier series). A low-pass filter removes the high-order harmonics, and the less harmonic content the modulation leaves, the smaller the filter can be.
- Hardware tools named in the session: Altium Designer, Multisim, Eagle and KiCad for PCBs on FR4; Texas Instruments DSPs programmed in Code Composer Studio; FPGAs programmed in VHDL or Verilog; and PLECS RT Box, dSPACE, OPAL-RT, Typhoon HIL and RTDS for hardware-in-the-loop testing of control code without building the power stage.
What is the difference between bipolar and unipolar PWM in a single-phase inverter?
Bipolar PWM switches diagonal pairs together, so the output swings between +Vdc and -Vdc and harmonics sit at every multiple of the carrier ratio. Unipolar PWM controls each leg separately, so the output steps between zero and one polarity. In the session's PLECS demo, unipolar gave lower voltage and current THD.
How does sinusoidal PWM control an inverter's output voltage and frequency?
A sine reference is compared with a fixed triangular carrier, and a switch turns on whenever the sine is above the carrier. Raising the sine amplitude relative to the carrier widens the pulses and raises output voltage. Changing the sine's frequency changes the output frequency, giving variable voltage and variable frequency from a fixed DC source.
Why does a grid-connected inverter need a low-pass filter?
The bridge output is a train of pulses, not a sine wave. It contains the wanted fundamental plus switching harmonics. A low-pass LC filter blocks the high-frequency components so near-sinusoidal voltage and current reach the grid. A modulation scheme with fewer harmonics, such as unipolar PWM, allows a smaller filter.
Where to go next
- Skill-Lync course: power electronic converter design, including single-phase and three-phase inverters
- Power Electronics interactive book with simulations
- GATE Electrical: solved inverter and DC-DC converter PYQs
- Workshop notes: power electronics converters for solar energy
- Workshop notes: Introduction to Power Electronics (devices, tools, industry roles)
Who should watch
For Electrical Engineers
A 24 Mar 2021 workshop recording from Skill-Lync on ELECTRICAL. For a structured course with projects on this topic, see Skill-Lync's electrical engineering courses.