Theory of Machines cover
Interactive book · Semester 4-7

Theory of Machines

Change a link and watch a four-bar stop turning, slide a cam follower through SHM and cycloidal rise, and balance an engine's shaking force

24 chapters, 24 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers: mechanisms and Grashof's law, inversions and quick-return mechanisms, Hooke's joint, loop-closure analysis, velocity and acceleration polygons, instantaneous centres, the Coriolis component, synthesis, cams, gear tooth action, interference, gear trains, static and dynamic force analysis, governors, the gyroscope, balancing, and free and forced vibration.

  • AUME3491Theory of Machines
  • VTUBME503Theory of Machines
  • SPPU202047Kinematics of Machinery
  • SPPU402042Dynamics of Machinery
  • MUMEC403Kinematics of Machinery
  • MUMEC503Dynamics of Machinery
  • KTUPBMET404Mechanics of Machinery
  • KTUPCMET501Dynamics of Machinery

By Skill-Lync · Updated 19 Nov 2026 · 24 chapters · 24 interactives · free, no sign-up

Chapter 1

Links, pairs and mobility: the four-bar chain and Grashof's law

Which syllabus covers thisAU ME3491 Unit IVTU BME503 Module 1SPPU 202047 Unit IMU MEC403 Module 1KTU PBMET404 Module 1

Which link of a four-bar chain can turn fully, and what happens when you fix a different link?

Call the shortest link s, the longest l and the other two p and q. If s + l ≤ p + q (Grashof's condition), the shortest link can make full turns relative to its neighbours. If not, no link turns fully: every inversion is a triple rocker. Fixing each link in turn gives the inversions. Take links of 100, 30, 90 and 70 mm round the loop: 30 + 100 = 130, less than 90 + 70 = 160. Fix the 100 mm link and the 30 mm crank turns while the 70 mm link rocks: a crank-rocker. Fix the 30 mm link for a double crank, or the 90 mm link opposite it for a double rocker.

Four-bar chain and Grashof's law: which link turns fully, the inversions and the transmission angle: interactive loads as you scroll

What is the transmission angle and why does it matter?

The transmission angle μ is the angle between the coupler and the output link. The coupler can only push along its own length, so only the part of its force perpendicular to the output link turns it, in proportion to sin μ. At 90° all of the push is useful. Near 0° or 180° the push mostly loads the bearings and the linkage jams easily. μ swings between two extremes, reached when the crank lies along the frame line. For the 100/30/90/70 mm crank-rocker, μ runs from 50° to 108°.

What are toggle (dead-centre) positions, and why does a crank-rocker return faster?

A crank-rocker's rocker stops and reverses when the crank and coupler fall in line, once stretched out and once folded. Those two crank positions are not 180° apart, so at constant crank speed the rocker swings one way faster than the other. With links of 100, 30, 90 and 70 mm the rocker swings through 51.8°. The crank turns 187.9° for the slow stroke and 172.1° for the quick one, a time ratio of 1.091. A linkage driven from the rocker side locks at these positions: the dead centres.

Predict, then check

A four-bar has links of 100, 30, 90 and 70 mm and works as a crank-rocker with the 100 mm link fixed. You fix the 30 mm link instead. What happens?

Worked examples

Classify all four inversions of a chain · Four links joined in a loop, in order: 45, 120, 95 and 80 mm
  1. Shortest s = 45 mm, longest l = 120 mm, the others 95 and 80 mm: s + l = 165 mm, p + q = 175 mm, so the chain is Grashof
  2. Fix the 45 mm link (shortest): both its neighbours turn fully: double crank
  3. Fix the 80 mm or the 120 mm link (next to the shortest): the 45 mm link turns fully and the 95 mm link opposite it rocks: crank-rocker (with the 120 mm link fixed the 45 mm crank is the output, which the interactive labels rocker-crank)
  4. Fix the 95 mm link (opposite the shortest): only the coupler turns fully relative to its neighbours, both links on the frame rock: double rocker
  5. Each class was confirmed by a numeric sweep: turning each link through 360° in 0.1° steps and checking that the loop still closes

Answer: Grashof (165 < 175 mm): double crank with the 45 mm link fixed, crank-rocker with the 120 or 80 mm link fixed, double rocker with the 95 mm link fixed

Transmission angle, rocker swing and time ratio of a crank-rocker · Frame d = 100 mm, crank a = 30 mm, coupler b = 90 mm, rocker c = 70 mm
  1. Grashof: 30 + 100 = 130 < 90 + 70 = 160, with the shortest link as the crank: crank-rocker
  2. μ is smallest with the crank pointing at O4 (diagonal O4A = d − a = 70 mm): cos μ = (90² + 70² − 70²)/(2 × 90 × 70) = 0.6429, μmin = 49.99°
  3. μ is largest with the crank pointing away (O4A = d + a = 130 mm): cos μ = (90² + 70² − 130²)/(2 × 90 × 70) = −0.3095, μmax = 108.03°
  4. Toggles: O2B = b + a = 120 mm and b − a = 60 mm. The cosine rule in triangle O2O4B gives rocker angles of 87.95° and 36.18° from O4O2: swing = 51.77°
  5. Crank angles at the toggles: 35.66° and 223.53°, so the two strokes take 187.87° and 172.13° of crank turn: time ratio = 1.091

Answer: μ between 50° and 108°, rocker swing 51.8°, time ratio 1.091

How far can the input of a non-Grashof linkage swing? · Frame d = 90 mm, input a = 60 mm, coupler b = 50 mm, output c = 70 mm
  1. s + l = 50 + 90 = 140 mm > p + q = 60 + 70 = 130 mm: non-Grashof, every inversion is a triple rocker
  2. The diagonal O4A must lie between |b − c| = 20 mm and b + c = 120 mm
  3. O4A² = a² + d² − 2ad cos θ2. Setting O4A = 120 mm: cos θ2 = (60² + 90² − 120²)/(2 × 60 × 90) = −0.25
  4. θ2 max = 104.48°; O4A = 20 mm would need cos θ2 > 1, so the input passes through θ2 = 0 freely
  5. A step-by-step check (0.01° steps) finds the last closing angle at 104.47°

Answer: The input swings ±104.5° about the frame line; at the ends the coupler and output fall in line (toggle)

Chapter 2

Inversions of the slider-crank and double slider-crank chains, and quick-return mechanisms

Which syllabus covers thisAU ME3491 Unit IVTU BME503 Module 1SPPU 202047 Unit IMU MEC403 Module 1KTU PBMET404 Modules 1-2

What mechanisms come from fixing different links of the slider-crank chain?

The slider-crank chain has four links: frame, crank, connecting rod and slider, with three turning pairs and one sliding pair. Fixing the frame gives the engine and the compressor. Fixing the crank makes the frame and rod turn about separate centres: the Whitworth quick-return and the old rotary aero engine. Fixing the connecting rod lets the cylinder rock about a pin: the oscillating-cylinder engine and the crank-and-slotted-lever quick return of a shaper. Fixing the slider gives the hand pump, where the cylinder stands still and the frame swings.

What does the double slider-crank chain give?

Two sliding pairs and two turning pairs. Fix the frame with two perpendicular slots and a rod joining the sliders becomes the elliptical trammel. A point on a 100 mm rod, 70 mm from one slider and 30 mm from the other, traces an ellipse with semi-axes 70 and 30 mm. Fix a slider instead and you get the Scotch yoke, whose output is pure simple harmonic motion: a 50 mm crank at 300 rpm moves it at up to 1.57 m/s. Fix the link joining the sliders and you get Oldham's coupling, which drives a shaft that is offset but parallel.

How does a crank and slotted lever give a slow cutting stroke and a quick return?

The crank turns at a steady speed and its pin slides in a lever pivoted below. The lever's extreme positions come where it touches the crank circle, and the return stroke uses only the short arc of crank travel near the lever pivot, angle α with cos(α/2) = r/c. With a 100 mm crank and centres 300 mm apart, α = 141.1°, so cutting takes 218.9° of crank turn: a time ratio of 1.55. Slow cutting suits the tool and the fast return saves time.

Quick-return mechanisms: crank and slotted lever and Whitworth, time ratio, stroke and ram velocity: interactive loads as you scroll

How does the Whitworth mechanism differ?

In the Whitworth mechanism the crank is longer than the distance between the two fixed centres, so the slotted link turns fully instead of rocking. An arm on the slotted link drives the ram through a connecting rod, and the stroke is twice the arm. The ram stops when the slotted link lines up with the ram's path, which happens at crank angles 180° − 2·asin(c/r) apart on the short side. With a 100 mm crank, a 40 mm offset and a 120 mm arm, the time ratio is 1.71 and the stroke 240 mm.

Predict, then check

In a shaper's crank and slotted lever you keep the crank radius and move the lever pivot further from the crank centre. The time ratio (cutting time / return time)

Worked examples

Time ratio, stroke and ram speeds of a shaper · Crank and slotted lever: crank r = 90 mm, centre distance c = 270 mm, lever L = 480 mm (the ram follows the lever tip's horizontal position), crank speed 40 rpm
  1. Return angle: cos(α/2) = 90/270, α = 141.06°; cutting angle = 360° − α = 218.94°
  2. Time ratio = 218.94/141.06 = 1.552
  3. Lever swings to sin ψ = r/c each side: stroke = 2Lr/c = 2 × 480 × 90/270 = 320 mm
  4. ω = 2π × 40/60 = 4.189 rad/s. Fastest cutting is with the crank pin furthest from the pivot: v = Lωr/(c + r) = 0.503 m/s
  5. Fastest return is with the pin nearest the pivot: v = Lωr/(c − r) = 1.005 m/s, (c + r)/(c − r) = 2 times the cutting maximum

Answer: Time ratio 1.55, stroke 320 mm, maximum cutting speed 0.503 m/s and return speed 1.005 m/s

Size a slotted lever for a given time ratio and stroke · Required time ratio 1.6 and stroke 300 mm; the lever pivot sits 320 mm below the crank centre
  1. Cutting + return = 360° and cutting = 1.6 × return, so α = 360°/2.6 = 138.46°
  2. Crank radius r = c cos(α/2) = 320 × cos 69.23° = 113.5 mm
  3. Stroke = 2Lr/c, so lever length L = 300 × 320/(2 × 113.5) = 423 mm
  4. A numeric sweep of the ram position over one crank turn gives a 300 mm stroke and a 1.6 ratio

Answer: Crank radius 113.5 mm, lever length 423 mm

Sliding speed in an Oldham coupling · Two parallel shafts 8 mm apart joined by an Oldham coupling, running at 600 rpm
  1. The middle disc's tongues slide in perpendicular slots of the two flanges; its centre always lies at the foot of the perpendicular from one shaft axis to the other flange's slot
  2. Along flange 1's slot the disc centre sits at e cos θ from the axis, e = 8 mm
  3. Sliding speed = e ω sin θ, largest = e ω = 0.008 × 62.83 = 0.503 m/s
  4. The disc centre goes round a circle of diameter e at twice the shaft speed

Answer: Maximum sliding speed 0.503 m/s in each slot

Chapter 3

Hooke's joint, straight-line mechanisms and the pantograph

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU 202047 Unit IIMU MEC403 Module 2KTU PBMET404 Module 1

Why does a Hooke's joint not pass on a steady speed?

A Hooke's (Cardan) joint couples two shafts at an angle α through a cross whose arms sit in a fork on each shaft. Robert Hooke used the name universal joint in 1676. The output turns through the same angle per revolution, but not at a steady rate: tan θ = tan φ · cos α, with θ measured from where the input fork lies in the plane of the shafts. The speed ratio swings twice per turn between 1/cos α and cos α. At α = 20° and 900 rpm in, the output runs between 957.8 and 845.7 rpm.

Hooke's joint: output speed over a revolution, its fluctuation and the double joint that cancels it: interactive loads as you scroll

How does a double Hooke's joint give a steady output?

Put an intermediate shaft between two joints. If the input and output shafts make equal angles with it, and its two forks lie in the same plane, the second joint's speed variation exactly undoes the first: the output follows the input at every instant. Vehicle propeller shafts use this layout. Turn one fork 90° and the variations add instead. At 15° and 1500 rpm, one joint gives 1449 to 1553 rpm, while the wrongly phased pair gives 1400 to 1608 rpm, and the correct pair a steady 1500 rpm.

How can pin-jointed links draw a straight line?

Peaucellier and Lipkin's linkage (1864) is exact. Two long links from a fixed pivot O hold opposite corners of a rhombus, so the other two corners B and D stay on a line through O with OB × OD constant. With 150 mm links and 60 mm rhombus sides the product is 150² − 60² = 18900 mm². Drive B round a circle through O (a 70 mm link pivoted 70 mm away) and D moves along a straight line 135 mm from O. Watt's linkage (patented 1784) is approximate: with 100 mm levers and a 40 mm coupler, its midpoint strays only 0.17 mm sideways over ±30 mm of travel.

What does a pantograph do?

A pantograph is a parallelogram of four links with one point pinned to the frame. The fixed pivot, the tracing point and the pen always stay in a straight line, and their distances from the pivot keep a fixed ratio. So whatever the tracer follows, the pen draws the same shape, enlarged or reduced by that ratio. Set for 2.5 times, tracing a 40 mm circle draws a 100 mm circle. Moving the pins along the links changes the ratio, and swapping the tracer and pen turns an enlargement into a reduction.

Predict, then check

A single Hooke's joint turns at a steady input speed with the shafts at 25°. How many times per input revolution does the output reach its highest speed?

Worked examples

Speed range of a single Hooke's joint · Shafts at α = 20°, input 900 rpm steady
  1. Maximum ratio 1/cos 20° = 1.0642: output 957.8 rpm at θ = 0° and 180°
  2. Minimum ratio cos 20° = 0.9397: output 845.7 rpm at θ = 90° and 270°
  3. Total fluctuation = 1/cos α − cos α = sin α tan α = 0.1245, i.e. 12.45 % of the input speed
  4. Equal speeds where cos²θ = 1/(1 + cos α): θ = 44.11°, 135.89°, 224.11° and 315.89°
  5. Differentiating the ratio over a turn (numerically) gives a largest output angular acceleration of 1110 rad/s²

Answer: Output between 845.7 and 957.8 rpm, a fluctuation of 12.45 % of 900 rpm

Largest shaft angle for a given speed fluctuation · The output speed may vary by no more than 5 % of the input speed in total (max − min)
  1. Fluctuation = 1/cos α − cos α = 0.05
  2. Multiply by cos α: cos²α + 0.05 cos α − 1 = 0, so cos α = (−0.05 + √(0.0025 + 4))/2 = 0.97531
  3. α = 12.76° (a bisection on sin α tan α = 0.05 gives the same)

Answer: The shafts may meet at up to 12.76°

Double joint: correct and wrong phasing · Input and output shafts parallel, each at 15° to an intermediate shaft, input 1500 rpm
  1. One joint alone: output 1448.9 to 1552.9 rpm
  2. Forks of the intermediate shaft in the same plane: the second joint's ratio is the reciprocal of the first at every instant, so the output runs at a steady 1500 rpm
  3. Forks turned 90°: the ratios multiply, giving the range of one joint with cos²α = 0.933 in place of cos α
  4. Output then varies from 1500 × 0.933 = 1399.5 to 1500/0.933 = 1607.7 rpm

Answer: Steady 1500 rpm when correctly phased; 1399.5 to 1607.7 rpm with one fork turned 90°

Chapter 4

Analytical position and velocity analysis: loop closure, complex algebra and coupler curves

Which syllabus covers thisAU ME3491 Unit IVTU BME503 Module 1SPPU 202047 Unit IIMU not in syllabusKTU not in syllabus

How do you find the output angle of a four-bar without drawing it?

Write each link as a vector (a complex number) and go round the loop: a e^(iθ2) + b e^(iθ3) − c e^(iθ4) − d = 0, with frame d, crank a, coupler b and rocker c. Eliminate the coupler angle θ3 by moving the other terms across and squaring both sides. What is left is Freudenstein's equation, which links θ4 to θ2 alone through three link-ratio constants: K1 = d/a, K2 = d/c and K3 = (a² − b² + c² + d²)/(2ac). A tangent half-angle substitution turns it into a quadratic with two roots.

Why are there two answers, and how does a computer pick one?

For one crank angle the coupler and rocker can meet above or below the line from the crank pin to the rocker pivot: the open and crossed assemblies. Both satisfy the loop, and a real linkage stays on the one it was built in. For the 100/40/120/80 mm linkage at θ2 = 60°, θ4 = 64.94° (open) or 248.23° (crossed). Software often uses Newton-Raphson on the two loop equations instead. Started from a rough guess (θ3 = 20°, θ4 = 80°), it closes the loop to under 10⁻⁹ mm in 5 iterations. The starting guess picks the branch.

How does complex algebra give the angular velocities?

Differentiate the loop with respect to time. Each term a e^(iθ) becomes i a ω e^(iθ), so a ω2 e^(iθ2) + b ω3 e^(iθ3) = c ω4 e^(iθ4). Multiply by e^(−iθ4) and take the imaginary part: ω4 drops out and ω3 = a ω2 sin(θ4 − θ2)/(b sin(θ3 − θ4)). Doing the same with e^(−iθ3) gives ω4. At θ2 = 60° and ω2 = 10 rad/s, the 100/40/120/80 mm linkage has ω3 = −0.396 rad/s and ω4 = 4.573 rad/s. Both blow up when sin(θ3 − θ4) = 0, at a toggle.

What is a coupler curve and why is it useful?

Any point fixed to the coupler traces a closed curve as the crank turns: the coupler curve. Its shape changes greatly with where the point sits, and designers choose points for their paths: a near-straight stretch, a dwell, a loop. Hoeken's linkage has crank 1, frame 2, and coupler and rocker 2.5 units, with the point on the coupler extended to twice its length. With a 40 mm crank its point runs 158 mm along a line straight to within 0.25 mm during half the crank turn. Its speed there varies by about 44 %.

Four-bar by loop closure: output angle, velocity ratios by complex algebra and the coupler curve: interactive loads as you scroll
Predict, then check

Freudenstein's equation gives two values of θ4 for one crank angle. What are they?

Worked examples

Output and coupler angles by Freudenstein's equation · Frame d = 100 mm, crank a = 40 mm, coupler b = 120 mm, rocker c = 80 mm, crank angle θ2 = 60°
  1. K1 = d/a = 2.5, K2 = d/c = 1.25, K3 = (40² − 120² + 80² + 100²)/(2 × 40 × 80) = 0.5625
  2. Write it as P cos θ4 + Q sin θ4 + R = 0: P = cos θ2 − K1 = −2, Q = sin θ2 = 0.866, R = K2 cos θ2 − K3 = 0.0625
  3. θ4 = atan2(Q, P) ± acos(−R/√(P² + Q²)) = 156.59° ± 91.64°
  4. Open branch θ4 = 64.94°, crossed θ4 = 248.23°
  5. Coupler angle from the loop (open): θ3 = 18.38°; loop residual below 10⁻⁹ mm; transmission angle 46.6°

Answer: θ4 = 64.94° (open) or 248.23° (crossed); θ3 = 18.38° on the open branch

Angular velocities by complex algebra · The same linkage on the open branch at θ2 = 60°, crank turning anticlockwise at ω2 = 10 rad/s
  1. ω3 = a ω2 sin(θ4 − θ2)/(b sin(θ3 − θ4)) = 40 × 10 × sin(4.94°)/(120 × sin(−46.57°)) = −0.396 rad/s
  2. ω4 = a ω2 sin(θ2 − θ3)/(c sin(θ4 − θ3)) = 40 × 10 × sin(41.62°)/(80 × sin(46.57°)) = 4.573 rad/s
  3. Speed of the crank pin A = a ω2 = 0.4 m/s; of the rocker pin B = c |ω4| = 0.366 m/s
  4. Central differences of the positions over ±10⁻⁶ rad of crank give the same ω3 and ω4

Answer: ω3 = −0.396 rad/s (clockwise, small), ω4 = 4.573 rad/s anticlockwise, VB = 0.366 m/s

Position and speed of a coupler point · The same linkage at θ2 = 60°, crank at 60 rpm (ω2 = 2π rad/s); P is 60 mm along AB from A and 30 mm to the left of AB
  1. A = (40 cos 60°, 40 sin 60°) = (20, 34.64) mm; θ3 = 18.38°
  2. P = A + (60 + 30i) e^(iθ3) = (67.48, 82.03) mm
  3. ω3 = −0.0396 × 2π = −0.2485 rad/s
  4. VP = iω2 a e^(iθ2) + iω3 (60 + 30i) e^(iθ3) = (−0.2059, 0.1139) m/s
  5. |VP| = 0.2353 m/s (a central difference of P's position gives the same)

Answer: P at (67.5, 82) mm moving at 0.235 m/s

Chapter 5

Velocity analysis by the relative velocity method and rubbing velocity at pins

Which syllabus covers thisAU ME3491 Unit IVTU BME503 Module 1SPPU 202047 Unit IIIMU MEC403 Module 3KTU PBMET404 Module 2

What is the relative velocity of two points on one rigid link?

A rigid link cannot stretch, so point B can only move relative to point A by turning about it. The velocity of B relative to A is therefore perpendicular to AB, and its size is ω × AB, where ω is the link's angular velocity. Add it to A's own velocity and you get B's: vB = vA + vBA. Every link in a mechanism has one ω, so once two velocities on a link are known, any third point follows. The method needs only the directions that the joints allow: perpendicular to a link about a fixed pivot, or along a slider's guide.

How is a velocity polygon drawn for a four-bar chain?

Choose a pole o and a scale. Draw oa perpendicular to the crank O2A with length ω2 × O2A. From a draw a line perpendicular to the coupler AB; from o draw a line perpendicular to the rocker O4B. They meet at b. Then ab is B's velocity relative to A and ob is B's velocity. Divide by the link lengths to get ω3 = ab/AB and ω4 = ob/O4B. In the interactive the book's four-bar (300, 100, 280, 200 mm) at θ2 = 60° and 200 rpm gives vA = 2.094 m/s, vB = 1.369 m/s, ω3 = 3.93 rad/s clockwise and ω4 = 6.85 rad/s counter-clockwise.

Velocity polygon of a four-bar or slider-crank, angular velocities and rubbing velocity at a pin: interactive loads as you scroll

How do you find the velocity of a point on the coupler that is not a pin?

Use the velocity image. On the polygon, the points a, b and p form a triangle similar to the link's triangle ABP, turned through 90° in the sense of ω3 and scaled by ω3. So you draw triangle abp on side ab with the same shape and the same order of letters, and op is P's velocity. In the book's four-bar P sits 140 mm along AB and 80 mm to its left; at θ2 = 60° and 200 rpm its speed is 1.467 m/s. The image works for any link and any number of points on it.

What is the rubbing velocity at a pin joint, and why does it matter?

The pin turns in its hole at the relative angular velocity of the two links it joins, so the surfaces slide past each other at r × |ω1 − ω2|, with r the pin radius and the ω's signed. When the links turn the same way the speeds subtract; when they turn opposite ways they add. At a pivot on the frame it is simply r × ω. Friction power and wear grow with this sliding speed. At θ2 = 60° and 200 rpm, 15 mm pins at A and B of the book's four-bar rub at 0.373 and 0.162 m/s.

Predict, then check

At a crank pin of 10 mm radius the crank turns at 20 rad/s counter-clockwise and the connecting rod at 5 rad/s clockwise. The rubbing velocity is

Worked examples

Velocity polygon of the book's four-bar · Four-bar O2O4 = 300 mm, O2A = 100 mm, AB = 280 mm, O4B = 200 mm; crank at θ2 = 120° turning counter-clockwise at 150 rpm; coupler point P 140 mm along AB and 80 mm to its left
  1. ω2 = 2π × 150/60 = 15.708 rad/s; vA = ω2 × O2A = 1.571 m/s, perpendicular to O2A
  2. Position (to scale or by the loop equation): AB at 19.6°, O4B at 115.5°
  3. From a draw a line ⊥ AB, from o a line ⊥ O4B; they meet at b: ab = 0.123 m/s, ob = vB = 1.553 m/s
  4. ω3 = ab/AB = 0.123/0.28 = 0.439 rad/s counter-clockwise; ω4 = ob/O4B = 1.553/0.2 = 7.766 rad/s counter-clockwise
  5. Velocity image abp similar to ABP gives op = vP = 1.596 m/s

Answer: vB = 1.553 m/s, ω3 = 0.439 rad/s counter-clockwise, ω4 = 7.766 rad/s counter-clockwise, vP = 1.596 m/s

Piston velocity and rubbing at the crank pin and gudgeon pin · An illustrative engine slider-crank: crank 50 mm, connecting rod 200 mm, 3000 rpm, crank 45° past top dead centre (piston farthest from the crank); crank pin radius 20 mm, gudgeon pin radius 10 mm
  1. ω = 2π × 3000/60 = 314.16 rad/s; vA = ωr = 15.708 m/s ⊥ crank
  2. Rod angle: sin β = (r/l) sin θ = 0.1768, β = 10.18°
  3. Polygon: ob along the stroke, ab ⊥ rod. Rod: ω_rod = ω cos θ/√(n² − sin² θ) = 56.42 rad/s, opposite sense to the crank; ab = 11.285 m/s
  4. Piston: vB = rω sin θ (1 + cos θ/√(n² − sin² θ)) = 13.102 m/s, towards the crank
  5. Crank pin: 0.020 × (314.16 + 56.42) = 7.412 m/s; gudgeon pin (piston does not rotate): 0.010 × 56.42 = 0.564 m/s

Answer: Piston 13.1 m/s; rubbing 7.41 m/s at the crank pin and 0.564 m/s at the gudgeon pin

Rubbing velocity at all four pins · The book's four-bar at θ2 = 210°, crank 240 rpm counter-clockwise; pins O2 and O4 of 12 mm radius, A and B of 10 mm radius
  1. ω2 = 25.133 rad/s; the polygon gives ω3 = 8.587 rad/s and ω4 = 1.531 rad/s (positive = counter-clockwise)
  2. O2 (crank on frame): 0.012 × 25.133 = 0.302 m/s
  3. A (crank and coupler): 0.010 × |25.133 − (8.587)| = 0.165 m/s
  4. B (coupler and rocker): 0.010 × |8.587 − (1.531)| = 0.071 m/s
  5. O4 (rocker on frame): 0.012 × 1.531 = 0.018 m/s

Answer: O2 0.302, A 0.165, B 0.071, O4 0.018 m/s

Chapter 6

Instantaneous centres, Kennedy's theorem and the angular velocity ratio theorem

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU 202047 Unit IIIMU MEC403 Module 3KTU PBMET404 Module 2

What is an instantaneous centre, and how many does a mechanism have?

At any instant a link in plane motion turns about some point, its instantaneous centre (I-centre) relative to the frame. Every point of the link moves perpendicular to its line from that centre, at ω × distance. More generally, any two links have a relative I-centre: the one point where both have the same velocity. A pin joint is one by inspection. A slider's is at infinity, perpendicular to its path, and a rolling contact's is the contact point. A mechanism of n links has n(n − 1)/2 centres: 6 for a four-bar, 15 for a six-link chain.

What does Kennedy's theorem say, and how does it locate the hidden centres of a four-bar?

Any three links in plane motion have three relative I-centres, and they lie on one straight line. Aronhold (1872) and Kennedy (1886) found it independently. Number the four-bar 1 frame, 2 crank, 3 coupler, 4 rocker. I12, I23, I34 and I14 are the pins. Links 1, 2, 3 put I13 on line I12-I23, and links 1, 3, 4 put it on line I14-I34, so I13 is where O2A and O4B meet. Likewise I24 is where the ground line meets AB. In the interactive at θ2 = 40°, I13 is at (331, 278) mm from O2.

All six instantaneous centres of a four-bar by Kennedy's theorem, and the angular velocity ratios: interactive loads as you scroll

How do the centres give angular velocity ratios directly?

I24 is a point common to links 2 and 4, so its velocity is the same whether you treat it as part of the crank (turning about I12) or of the rocker (turning about I14). That gives ω4/ω2 = I12I24/I14I24. If I24 lies outside the segment I12-I14 the two links turn the same way; if it lies between them, opposite ways. The same idea with I23 gives ω3/ω2 = I12I23/I13I23. No polygon is needed: one intersection and two lengths.

What are the limits of the I-centre method?

An I-centre has zero velocity only at that instant; it generally has an acceleration, and it moves as the mechanism turns. So I-centres give velocities, not accelerations: for those you still need the acceleration polygon. The centres can also run off the drawing. When O2A and O4B are parallel, I13 is at infinity and the coupler is momentarily translating (ω3 = 0). The book's four-bar does this twice per turn, at θ2 = 111.1° and 304.4°.

Predict, then check

In a four-bar, I24 falls between the fixed pivots O2 and O4. The rocker turns

Worked examples

Angular velocities of the book's four-bar from its I-centres · Four-bar O2O4 = 300 mm, O2A = 100 mm, AB = 280 mm, O4B = 200 mm, coupler point P 140 mm along AB and 80 mm to its left; θ2 = 90°, crank 120 rpm counter-clockwise
  1. ω2 = 12.566 rad/s. With O2 at the origin and O4 at (300, 0) mm: A = (0, 100) mm, B = (262.8, 196.5) mm
  2. I24 = ground line ∩ line AB: x = −272.3 mm from O2 (outside O2O4, so the rocker turns the same way as the crank)
  3. ω4 = ω2 × I12I24/I14I24 = 12.566 × −272.3/−572.3 = 5.979 rad/s
  4. I13 = line O2A ∩ line O4B = (0, 1586.5) mm; I13A = 1486.5 mm
  5. ω3 = vA/I13A = 1.2566/1.4865 = 0.845 rad/s clockwise
  6. vB = ω3 × I13B = 1.196 m/s; vP = ω3 × I13P = 0.845 × 1.3671 = 1.156 m/s

Answer: ω4 = 5.979 rad/s (counter-clockwise), ω3 = 0.845 rad/s clockwise, vB = 1.196 m/s, vP = 1.156 m/s

Piston velocity of a slider-crank by I-centres · Slider-crank with crank 60 mm and rod 240 mm (in line), crank 45° past top dead centre, 1500 rpm
  1. ω = 157.08 rad/s; A = (42.43, 42.43) mm; piston pin B at x = 278.65 mm
  2. The slider's centre with the frame is at infinity ⊥ the stroke, so the rod's I13 is where the crank line OA meets the perpendicular to the stroke through B: (278.6, 278.6) mm
  3. I13A = 334.1 mm, so ω_rod = vA/I13A = 9.425/0.3341 = 28.21 rad/s
  4. vB = ω_rod × I13B = 28.21 × 0.2786 = 7.861 m/s
  5. Check by I24: AB extended meets the line through O ⊥ the stroke at 50.05 mm from O; vB = ω × OI24 = 7.861 m/s

Answer: Rod 28.21 rad/s, piston 7.86 m/s

Two wheels in rolling contact · An illustrative pair of friction wheels: wheel 2 of radius 80 mm on a fixed pivot drives wheel 3 of radius 200 mm by rolling without slip; wheel 2 at 300 rpm
  1. I12 and I13 are the fixed centres, I23 is the contact point (no slip, so both wheels have the same velocity there)
  2. Kennedy: I12, I13 and I23 are collinear, so the contact lies on the line of centres
  3. ω3/ω2 = I12I23/I13I23 with sign: external contact puts I23 between the centres, ratio = −80/200 = −0.4
  4. N3 = 300 × 0.4 = 120 rpm, opposite sense; contact speed = 2.513 m/s on both wheels
  5. An 80 mm wheel rolling inside a 200 mm ring has I23 outside the centres: ratio +0.4, same sense

Answer: Wheel 3 turns at 120 rpm in the opposite sense (ratio −0.4); internal contact gives +0.4

Chapter 7

Acceleration analysis: centripetal and tangential components and the acceleration polygon

Which syllabus covers thisAU ME3491 Unit IVTU BME503 Module 1SPPU 202047 Units II-IIIMU MEC403 Module 3KTU PBMET404 Module 2

What are the two parts of the relative acceleration between two points on a link?

Point B turning about A on a link with angular velocity ω and angular acceleration α has two parts of acceleration relative to A. The centripetal part ω² × AB points from B towards A and exists whenever the link turns. The tangential part α × AB is perpendicular to AB and exists only when ω is changing. The book's 100 mm crank at a steady 200 rpm has only the centripetal part at its pin: 20.944² × 0.1 = 43.86 m/s², pointing at O2.

How is the acceleration polygon of a four-bar built?

Solve velocities first: every centripetal term needs ω. From the pole draw A's acceleration: ω2²·O2A towards O2, plus α2·O2A if the crank is speeding up or slowing. From its end add ω3²·AB towards A, then a line perpendicular to AB of unknown length. From the pole draw ω4²·O4B towards O4, then a line perpendicular to O4B. The two lines meet at b. In the interactive at θ2 = 60° and a steady 200 rpm, the book's four-bar gives α3 = 123.3 rad/s² and α4 = 197.9 rad/s², both counter-clockwise, and B accelerates at 40.68 m/s².

Acceleration polygon of a four-bar: centripetal and tangential parts and the angular accelerations: interactive loads as you scroll

How do you get the acceleration of a coupler point, such as a centre of mass?

Use the acceleration image. Triangle a'b'p' on the acceleration polygon is similar to the link's triangle ABP, with the letters in the same order, just as for velocities. Its size and turn are set by ω² and α rather than ω. That is how the centre of mass of a coupler is found for inertia forces in dynamic force analysis. For the book's coupler point P at θ2 = 60° and 200 rpm the image gives 48.46 m/s², more than B's 40.68 m/s².

What changes when the crank's speed is not constant?

A crank driven by an engine or a motor that is speeding up has α2 ≠ 0, which adds a tangential term α2 × O2A at the crank pin, perpendicular to the crank. The rest of the construction is unchanged. Because the loop equations are linear in α, the extra α3 and α4 are just α2 times the velocity ratios ω3/ω2 and ω4/ω2. Slowing the book's crank at 150 rad/s² at θ2 = 60° and 200 rpm moves α3 from 123.3 to 151.4 rad/s² and α4 from 197.9 to 148.9 rad/s².

Predict, then check

A crank turns at constant speed. The acceleration of its crank pin

Worked examples

Acceleration polygon of the book's four-bar · Four-bar O2O4 = 300 mm, O2A = 100 mm, AB = 280 mm, O4B = 200 mm; θ2 = 120°, crank at a steady 150 rpm counter-clockwise (velocities from the chapter 5 example: ω3 = 0.439, ω4 = 7.766 rad/s, positive counter-clockwise)
  1. Crank pin: ω2²·O2A = 15.708² × 0.1 = 24.674 m/s² towards O2 (no tangential part)
  2. B relative to A, centripetal: ω3²·AB = 0.439² × 0.28 = 0.054 m/s² towards A
  3. B about O4, centripetal: ω4²·O4B = 7.766² × 0.2 = 12.063 m/s² towards O4
  4. Close the polygon with the two tangential lines (⊥ AB and ⊥ O4B): tangential parts 12.598 and 3.173 m/s²
  5. α3 = 12.598/0.28 = 44.99 rad/s² counter-clockwise; α4 = 3.173/0.2 = 15.87 rad/s² clockwise
  6. aB = √(12.063² + 3.173²) = 12.474 m/s²; image gives aP = 18.003 m/s²

Answer: α3 = 44.99 rad/s² counter-clockwise, α4 = 15.87 rad/s² clockwise, aB = 12.47 m/s², aP = 18 m/s²

Piston acceleration: polygon against the two-term formula · The illustrative slider-crank of chapter 5: crank 50 mm, rod 200 mm (n = 4), 3000 rpm, θ = 45° past top dead centre; ω_rod = 56.42 rad/s clockwise
  1. Crank pin: ω²r = 314.16² × 0.05 = 4935 m/s² towards O
  2. Rod centripetal: ω_rod² × l = 56.42² × 0.2 = 637 m/s² from B towards A
  3. Tangential line ⊥ rod meets the stroke line through o: α_rod = 17155 rad/s²
  4. Piston acceleration ob = 3510 m/s² towards the crank
  5. Two-term formula rω²(cos θ + cos 2θ/n) = 4935 × (0.7071 + 0) = 3489 m/s², −0.58% from the polygon

Answer: Piston acceleration 3510 m/s² (polygon); the approximation gives 3489 m/s²

A crank that is slowing down · The book's four-bar at θ2 = 60°, crank at 200 rpm counter-clockwise but slowing at 150 rad/s² (α2 = −150 rad/s²)
  1. Crank pin: centripetal 43.865 m/s² towards O2, tangential α2·O2A = 15 m/s² ⊥ crank (clockwise sense); |aA| = 46.359 m/s²
  2. Centripetal terms are unchanged: ω3²·AB = 4.32 m/s², ω4²·O4B = 9.376 m/s²
  3. Closing the polygon: α3 = 151.4 rad/s², α4 = 148.89 rad/s² (counter-clockwise positive)
  4. Compared with steady running (123.27 and 197.92): the changes 28.13 and −49.04 equal −150 × ω3/ω2 and −150 × ω4/ω2
  5. aB = 31.218 m/s², aP = 44.653 m/s²

Answer: α3 = 151.4 rad/s², α4 = 148.9 rad/s², aB = 31.22 m/s²

Chapter 8

The Coriolis component of acceleration in slotted-link mechanisms

Which syllabus covers thisAU not in syllabusVTU BME503 Module 1SPPU 202047 Unit IIIMU MEC403 Module 3KTU PBMET404 Module 2

When does a Coriolis component of acceleration appear?

Whenever a point slides along a link that is itself turning: a block in the slot of a shaper's lever, a piston in an oscillating cylinder, a bead on a spinning rod. Seen from the fixed frame, the block's acceleration then has an extra part 2vω, with v the sliding speed along the link and ω the link's angular velocity. G.-G. de Coriolis set out this term in 1835. Earth turns at 7.292 × 10⁻⁵ rad/s, so even at 20 m/s the term is at most 2.92 mm/s². In a shaper it is metres per second squared.

Which way does the Coriolis component point?

It is perpendicular to the link. Take the sliding velocity of the block relative to the link and turn it through 90° in the sense the link is rotating; that is the direction of 2vω. A block sliding outward on a link turning counter-clockwise gets a Coriolis component pointing counter-clockwise across the link. Reverse either the sliding or the rotation and it flips. In vector form it is 2ω × v.

How is the Coriolis component used in the crank and slotted lever?

The crank pin's acceleration is known (ω2²r towards the crank centre). The coincident point on the lever is unknown. Write pin = lever point + sliding + Coriolis. The lever point has a centripetal part sω4² towards the pivot and a tangential part sα4 across the lever. The sliding part runs along the slot, and the Coriolis part 2·ṡ·ω4 runs across it. With the crank centre 300 mm above the pivot, a 150 mm crank at 60 rpm and θ = 20°: ω4 = 1.662 rad/s, ṡ = 0.702 m/s, 2ṡω4 = 2.333 m/s² and α4 = 5.49 rad/s².

Coriolis component in a crank and slotted lever: sliding velocity, 2vω and the slotted link's motion: interactive loads as you scroll

When is the Coriolis component zero in a slotted lever?

It vanishes when either factor does. ṡ = 0 when the crank is at right angles to the line of centres (the block is momentarily at its farthest or nearest point along the slot). ω4 = 0 at the two ends of the lever's swing, where the lever is tangent to the crank circle and sin θ = −r/d. So it is zero four times per turn. With r = 120 mm and d = 300 mm the lever swings through 47.16° and the cutting-to-return time ratio is 1.71.

Predict, then check

A block slides outward along a link that is turning clockwise. The Coriolis component on the block points

Worked examples

Crank and slotted lever: all four parts · Lever pivot O; crank centre C 300 mm vertically above O; crank 150 mm turning counter-clockwise at a steady 45 rpm; θ = 120° from the horizontal. Signs: along the slot positive outward from O, across it and for rotations positive counter-clockwise
  1. ω2 = 4.7124 rad/s; s = √(r² + d² + 2dr sin θ) = 436.4 mm
  2. Pin speed ω2r = 0.7069 m/s splits into sliding ṡ = −0.243 m/s (towards O) and sω4 across the slot: ω4 = 1.5211 rad/s counter-clockwise
  3. Coriolis 2ṡω4 = 2 × (−0.243) × 1.5211 = −0.7391 m/s²: the inward sliding velocity turned 90° counter-clockwise, which points clockwise across the slot
  4. Lever centripetal sω4² = 1.0097 m/s² towards O
  5. Pin acceleration ω2²r = 3.331 m/s² towards C: components −3.128 m/s² along the slot and −1.1449 m/s² across it
  6. Across: 2ṡω4 + sα4 = −1.1449, so sα4 = −0.4058 m/s² and α4 = −0.9299 rad/s²
  7. Along: (sliding acceleration) − sω4² = −3.128, so the sliding acceleration = −2.1184 m/s²

Answer: ω4 = 1.521 rad/s counter-clockwise; Coriolis 0.739 m/s² and α4 = 0.93 rad/s², both clockwise; sliding acceleration 2.118 m/s² towards O

A block on a rotating arm · An illustrative arm turning counter-clockwise at a steady 30 rpm; a block 250 mm from the pivot slides outward at 0.4 m/s and is speeding up along the arm at 0.5 m/s²
  1. ω = 3.1416 rad/s, α = 0
  2. Centripetal sω² = 0.25 × 3.1416² = 2.4674 m/s² towards the pivot
  3. Along the arm: 0.5 − 2.4674 = −1.9674 m/s² (negative: towards the pivot)
  4. Coriolis 2vω = 2 × 0.4 × 3.1416 = 2.5133 m/s², across the arm, turned 90° counter-clockwise from the outward sliding velocity
  5. Total = √(−1.9674² + 2.5133²) = 3.1917 m/s²

Answer: 3.192 m/s², of which 2.513 m/s² is the Coriolis component

Where the Coriolis component vanishes, and the quick return · Crank and slotted lever with crank 120 mm and centre distance 300 mm, crank turning at steady speed
  1. ṡ = 0 when cos θ = 0: θ = 90° (block farthest from O) and θ = 270° (nearest)
  2. ω4 = 0 when sin θ = −r/d = −0.4: θ = 203.58° and 336.42°, the ends of the lever's swing
  3. Swing = 2 asin(r/d) = 47.16°
  4. The stroke made while the pin passes near O takes 2 acos(r/d) = 132.84° of crank turn, the other 227.16°
  5. Time ratio = 227.16/132.84 = 1.71; the lever turns 2.333 times faster at θ = 270° than at 90°

Answer: Coriolis is zero at θ = 90°, 203.6°, 270° and 336.4°; swing 47.2°, time ratio 1.71

Chapter 9

Synthesis of mechanisms: function generation, Chebyshev spacing and Freudenstein's equation

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU 202047 Unit IVMU not in syllabusKTU PBMET404 Module 3

What do function, path and motion generation ask a linkage to do?

Analysis takes a linkage and finds its motion. Synthesis runs the other way: choose link lengths for a wanted motion. Function generation makes the output angle follow a rule of the input angle, such as φ proportional to log x: a mechanical calculator or a linkage-driven gauge. Path generation makes a coupler point trace a curve, as in a film-advance claw. Motion generation guides a whole body through set positions, like a bucket or a hood. A four-bar has only a few lengths to choose, so it can match the wanted motion exactly at a few precision points and only approximately between them.

Where should the precision points go?

The error between precision points cannot be avoided, but where you place the points sets how big it gets. Chebyshev spacing puts n points at x_j = (a+b)/2 − (b−a)/2·cos((2j−1)π/2n). For three points on 1 ≤ x ≤ 2 that is x = 1.067, 1.5 and 1.933: closer to the ends than equal thirds. For the log x generator in the interactive, these points give a maximum error of 0.17 % of the output range. Putting the points at the two ends and the middle gives 0.25 %, and at 1/6, 1/2 and 5/6 of the range 0.4 %.

How does Freudenstein's equation turn three precision points into link lengths?

Take a four-bar with crank a at θ, coupler b, rocker c at φ and ground d, and eliminate the coupler angle from its loop closure, as Ferdinand Freudenstein did in his PhD work at Columbia. The result is K1 cos φ − K2 cos θ + K3 = cos(θ − φ), with K1 = d/a, K2 = d/c and K3 = (a² − b² + c² + d²)/(2ac). It is linear in the K's: three (θ, φ) pairs give three equations; solve, pick d, and get a, c and b. The log x generator in the interactive comes out at a : b : c : d = 0.713 : 1.658 : 0.716 : 1.

Function generator by Freudenstein's equation with Chebyshev precision points, and its structural error: interactive loads as you scroll

What is structural error, and what else can go wrong with a synthesised linkage?

Structural error is the difference between the angle the linkage gives and the angle the function wants, with perfect parts. It is zero at the precision points and swings between them. Errors from tolerances and pin clearance are separate (mechanical error). The sin x generator over 0-90° has 2.09 %, because the function bends a lot. Also check the answer. A negative K means that link points the other way. The linkage may need to change branch between precision points, which it cannot do without being taken apart. It may also lock between them. Then change the ranges or start angles and solve again.

Predict, then check

You move the three precision points of a function generator from equal spacing at 1/6, 1/2 and 5/6 of the range to Chebyshev spacing. The largest structural error over the range

Worked examples

Chebyshev precision points and their angles · Generate y = x² for 1 ≤ x ≤ 3 with three precision points. The crank turns from 40° through 90° and the rocker from 20° through 80°, both linearly in x and y
  1. Chebyshev points: x = 2 − cos 30°, 2, 2 + cos 30° = 1.134, 2, 2.866
  2. y = x² = 1.2859, 4, 8.2141
  3. θ = 40° + (x − 1)/2 × 90° = 46.03°, 85°, 123.97°
  4. φ = 20° + (y − 1)/8 × 80° = 22.86°, 50°, 92.14°
  5. These three (θ, φ) pairs go into Freudenstein's equation

Answer: (θ, φ) = (46.03°, 22.86°), (85°, 50°), (123.97°, 92.14°)

Link lengths of a square-root generator · Generate y = √x for 1 ≤ x ≤ 4. The crank turns from 60° through 90°, the rocker from 15° through 90°, three Chebyshev precision points, ground link 80 mm
  1. x = 1.201, 2.5, 3.799; y = √x = 1.0959, 1.5811, 1.9491
  2. θ = 66.03°, 105°, 143.97°; φ = 15° + (y − 1) × 90° = 23.63°, 67.3°, 100.42°
  3. Each pair gives K1 cos φ − K2 cos θ + K3 = cos(θ − φ): three linear equations
  4. Solving: K1 = 0.8585, K2 = 0.7639, K3 = 0.2623
  5. a = d/K1 = 80/0.8585 = 93.2 mm; c = d/K2 = 104.7 mm
  6. b² = a² + c² + d² − 2ac·K3 → b = 144.7 mm
  7. Shortest + longest = 224.7 mm > sum of the other two = 197.9 mm: not a Grashof linkage, which is fine because the crank only has to swing 90°

Answer: Crank 93.2 mm, coupler 144.7 mm, rocker 104.7 mm on an 80 mm ground; largest structural error 0.23 % of the output range

Structural error between precision points · The square-root generator above (crank 93.2, coupler 144.7, rocker 104.7, ground 80 mm) at x = 3.25, which is not a precision point
  1. θ = 60° + (3.25 − 1)/3 × 90° = 127.5°; wanted φ = 15° + (√3.25 − 1) × 90° = 87.25°
  2. Vector from O4 to the crank pin: (−136.73, 73.93) mm, length 155.43 mm
  3. Rocker angle from the coupler-length condition: φ = 87.45° (the same branch as the precision points; a bisection on |AB| − b agrees)
  4. Structural error = 87.45° − 87.25° = 0.2°, or 0.223 % of the 90° output range

Answer: The linkage is 0.2° ahead of the wanted angle at x = 3.25 (largest anywhere: 0.205°)

Chapter 10

Cams and followers: uniform velocity, SHM, uniform acceleration and cycloidal motion

Which syllabus covers thisAU ME3491 Unit IVTU not in syllabusSPPU 202047 Unit VIMU MEC403 Module 4KTU PBMET404 Module 3

What does a cam's displacement diagram show?

A cam turns at constant speed and pushes a follower through a planned cycle: rise, dwell (no movement), return, dwell. The displacement diagram plots follower lift s against cam angle θ. The lift h, the rise angle and the return angle are the design inputs. Because the cam speed is constant, angle is just time: at 300 rpm one turn takes 0.2 s, so a 120° rise lasts 0.0667 s. Velocity is ω·ds/dθ and acceleration is ω²·d²s/dθ². The shape of the rise decides how hard the follower is shaken.

What goes wrong with uniform velocity, and how does SHM fix it?

Uniform velocity (a straight-line rise) is the obvious choice. But the follower must jump from rest to full speed at the start, and that needs infinite acceleration: a shock at every end of the rise and return. Simple harmonic motion takes the rise along half a cosine, s = (h/2)(1 − cos(πθ/β)). Velocity now starts and ends at zero. A 20 mm SHM rise over 120° at 300 rpm peaks at 0.471 m/s and 22.2 m/s² (uniform velocity: 0.3 m/s, with infinite acceleration at the ends). SHM still has a jump in acceleration at each end.

Follower motion: displacement, velocity and acceleration for uniform velocity, SHM, UARM and cycloidal: interactive loads as you scroll

Why use uniform acceleration and retardation?

Uniform acceleration and retardation (UARM, parabolic motion) accelerates evenly for the first half of the rise and slows evenly for the second, s = 2h(θ/β)² then mirrored. For a given lift, rise angle and speed it has the smallest possible peak acceleration: 4hω²/β², against π²/2 = 4.93 for SHM and 2π = 6.28 for cycloidal. For the 20 mm, 120°, 300 rpm rise: 18 m/s² and a peak velocity of 0.6 m/s. The cost is that the acceleration switches suddenly at the start, the middle and the end. Each switch is an infinite jerk.

Why is cycloidal motion preferred at high speed?

Cycloidal motion, s = h(θ/β − sin(2πθ/β)/2π), is the path of a point on a rolling circle. Its acceleration is a full sine wave that starts and ends at zero, so velocity and acceleration are continuous and the jerk stays finite everywhere. That means less vibration and noise, and less risk of the follower leaving the cam. Its peak acceleration is the highest of the four: 28.3 m/s² for the 20 mm, 120°, 300 rpm rise. The jerk at the ends is 2665 m/s³, large but finite. That is why designers of high-speed cams favour cycloidal or polynomial curves.

Predict, then check

For the same lift, rise angle and cam speed, which rise has the lowest peak acceleration?

Worked examples

SHM rise · A follower rises 25 mm with SHM while the cam turns 100° at 450 rpm
  1. ω = 2π × 450/60 = 47.124 rad/s; β = 100° = 1.7453 rad
  2. At θ = 40°: s = 12.5(1 − cos(π × 40/100)) = 8.637 mm
  3. v at 40° = (πhω/2β) sin(0.4π) = 1.008 m/s
  4. vmax = πhω/(2β) = π × 25 × 47.124/(2 × 1.7453) = 1060.3 mm/s = 1.06 m/s, at mid-rise
  5. amax = π²hω²/(2β²) = 89.9 m/s², at the start and end of the rise

Answer: s = 8.64 mm at 40°; vmax = 1.06 m/s; amax = 89.9 m/s²

Cycloidal return · The same cam (450 rpm) returns the follower 25 mm with cycloidal motion over 90°
  1. β = 90° = 1.5708 rad; 30° into the return u = 1/3
  2. s = 25[1 − (1/3 − sin(120°)/2π)] = 20.112 mm
  3. v = −(hω/β)(1 − cos 120°) = −1.125 m/s (moving down)
  4. a = −(2πhω²/β²) sin 120° = −122.4 m/s²
  5. Peaks: vmax = 2hω/β = 1.5 m/s at mid-return, amax = 2πhω²/β² = 141.4 m/s² at the quarter points; a = 0 at both ends

Answer: s = 20.11 mm, v = −1.125 m/s, a = −122.4 m/s² at 30°; vmax 1.5 m/s, amax 141.4 m/s²

Spring force to keep a follower on a UARM cam · A 0.4 kg follower (illustrative) rises 18 mm with UARM over 80° of a cam at 900 rpm. In the second half of the rise the follower is slowing, and only the spring can hold it against the cam
  1. ω = 2π × 900/60 = 94.25 rad/s; β = 1.3963 rad
  2. Retardation = 4hω²/β² = 4 × 18 × 94.25²/1.3963² = 328050 mm/s² = 328 m/s²
  3. Force needed = m·a = 0.4 × 328 = 131.2 N (more than gravity can give: 0.4 × 9.81 = 3.92 N)
  4. With SHM the end retardation would be 404.7 m/s² (161.9 N); with cycloidal 515.3 m/s² (206.1 N)
  5. Peak velocity = 2hω/β = 2.43 m/s

Answer: The spring must push down with at least 131.2 N at the top of the rise, or the follower leaves the cam (jump)

Chapter 11

Cam profiles for knife-edge, roller and flat-faced followers, offset and pressure angle

Which syllabus covers thisAU ME3491 Unit IVTU not in syllabusSPPU 202047 Unit VIMU MEC403 Module 4KTU PBMET404 Module 3

How is a cam profile drawn from the displacement diagram?

By kinematic inversion. Hold the cam still and swing the follower round it the opposite way, at each angle placing it at its lift s. A knife-edge tip then traces the profile directly. For a roller, the roller centre traces the pitch curve, and the cam profile is the inner envelope of the roller circles: the pitch curve moved inwards by the roller radius. The prime circle (base circle + roller radius) is where the pitch curve starts. With rb = 25 mm and a 12 mm roller, at 60° of a 30 mm SHM rise the roller centre sits 52 mm from the cam centre.

What is the pressure angle, and why keep it small?

The cam can only push along the common normal at the contact. The pressure angle is the angle between that normal and the follower's line of motion. Only its cosine component lifts the follower; the sine component presses the stem sideways into its guide, adds friction and can jam it. A common limit is 30° for translating followers. For a 30 mm SHM rise over 120° with a 10 mm roller, a 20 mm base circle gives 27.9°, 30 mm gives 23° and 40 mm gives 19.6°. A bigger base circle is the usual cure.

Cam profile by inversion for knife-edge, roller and flat-faced followers, offset and pressure angle: interactive loads as you scroll

What does offsetting the follower do?

Moving the follower's line of motion sideways by e changes the pressure angle by subtracting e from ds/dθ in the formula. With the offset on the correct side for the direction of rotation, it lowers the angle on the rise but raises it on the return. With a 30 mm base circle and 10 mm roller, an 8 mm offset takes the rise maximum from 23° to 15.3° and the return maximum from 23° to 30.7°. That suits cams where the rise does the work and a spring brings the follower back.

When is a cam undercut?

For a roller, the pitch curve's radius of curvature must exceed the roller radius wherever the curve is convex. If not, the offset profile folds over itself and the roller cannot follow it. For a flat-faced follower, the profile's radius of curvature is rb + s + d²s/dθ², and it must stay positive. A cycloidal 30 mm rise over 120° reaches d²s/dθ² = −43 mm, so the base circle must exceed 16 mm. The flat face must also be wide enough: the contact moves ds/dθ from the stem, here up to 28.6 mm.

Predict, then check

A roller cam with a 30 mm SHM rise over 120° has a 20 mm base circle. You double the base circle to 40 mm, with the same roller, lift and motion. The maximum pressure angle

Worked examples

Pressure angle and the profile point of a roller cam · A roller follower (radius 12 mm, no offset) on a cam with base circle 25 mm rises 30 mm with SHM over 120°. Find the pressure angle and the points on the pitch curve and profile when the cam has turned 60° (counter-clockwise)
  1. Prime circle = 25 + 12 = 37 mm; at 60° (mid-rise) s = 15 mm
  2. ds/dθ = πh/(2β) = π × 30/(2 × 2.0944) = 22.5 mm/rad
  3. tan φ = 22.5/(37 + 15) → φ = 23.4°
  4. Roller centre: 52 mm from the cam centre. In the cam's own frame it is at (45.03, 26) mm (the follower position turned back by 60°)
  5. Profile point: 12 mm from the roller centre along the common normal, at (37.88, 16.37) mm in the cam frame

Answer: φ = 23.4°; pitch point (45.03, 26) mm, profile point (37.88, 16.37) mm

Effect of a 6 mm offset · The same cam and roller with the follower offset 6 mm, on the side that helps the rise. Compare mid-rise (60°) and mid-return (210°)
  1. √(rp² − e²) = √(37² − 6²) = 36.51 mm
  2. Mid-rise: tan φ = (22.5 − 6)/(36.51 + 15) → φ = 17.76° (was 23.4°)
  3. Mid-return: ds/dθ = −22.5 mm/rad; tan φ = (−22.5 − 6)/(36.51 + 15) → φ = −28.96° (was −23.4°)

Answer: The offset lowers the mid-rise pressure angle to 17.8° but raises the mid-return one to 29°

Base circle for a flat-faced follower · A flat-faced follower rises 24 mm with cycloidal motion over 100°. Find the smallest base circle that avoids undercutting, and how far the contact moves from the stem
  1. s = 24(u − sin 2πu/2π) and d²s/dθ² = (2π × 24/β²) sin 2πu with β = 1.7453 rad
  2. The profile radius rb + s + d²s/dθ² is smallest where s + d²s/dθ² is most negative: u = 0.7367 (θ = 73.7°), s = 21.487 mm, d²s/dθ² = −49.33 mm
  3. So rb > 27.84 mm
  4. The contact sits ds/dθ from the stem; the largest value, at mid-rise, is 2h/β = 2 × 24/1.7453 = 27.5 mm

Answer: Base circle above 27.8 mm; the face must reach at least 27.5 mm from the stem on the rise side (plus a margin)

Chapter 12

Spur gears: law of gearing, involute teeth, path and arc of contact and contact ratio

Which syllabus covers thisAU ME3491 Unit IIVTU BME503 Module 3SPPU 202047 Unit VMU MEC403 Module 6KTU PBMET404 Module 4

What is the law of gearing?

For two gears to keep a constant speed ratio, the common normal to the tooth profiles at the point of contact must always pass through one fixed point on the line of centres: the pitch point P. P divides the centre distance in the inverse ratio of the speeds, ω1/ω2 = O2P/O1P = z2/z1. Profiles that obey this are called conjugate. If the normal wandered, the ratio would wobble with every tooth and the gears would vibrate. At P itself the teeth roll without sliding; everywhere else they slide.

Why are almost all gear teeth involutes?

An involute is the curve traced by the end of a taut string unwound from a circle, the base circle. Two involute teeth always touch on the common tangent to both base circles, so the normal never moves: that line is the line of action, and its angle to the common tangent at P is the pressure angle φ. A bonus: a change in centre distance does not spoil the speed ratio, because the base circles set it. Pull a 20/50 pair with module 4 mm from 140 to 141 mm apart and the ratio stays 2.5. Only the working pressure angle grows, from 20° to 21.09°.

What are the standard tooth proportions?

Size is set by the module m (mm): pitch diameter d = z·m and circular pitch πm. The common standard basic rack has a pressure angle of 20°, an addendum (pitch circle to tip) of 1 module and a dedendum (pitch circle to root) of 1.25 modules. That makes a full-depth tooth 2.25 modules deep, with 0.25 m of clearance at the root. The base circle is d·cos φ. The older 14.5° and the stronger 25° are also standard pressure angles; mating gears must share both the module and the pressure angle.

What are the path of contact, the arc of contact and the contact ratio?

Contact starts where the wheel's addendum circle cuts the line of action and ends where the pinion's addendum circle does. The part before P is the path of approach, the part after is the path of recess, and the two add up to the path of contact. The pitch circles roll through the arc of contact = path/cos φ. Contact ratio = path / base pitch (πm cos φ): the average number of tooth pairs in contact. In the interactive, a 20/50 pair with module 4 mm at 20° has a path of 19.55 mm and a contact ratio of 1.656.

Spur gear tooth action: line of action, path and arc of contact, contact ratio and sliding velocity: interactive loads as you scroll

How fast do the teeth slide on each other?

Away from the pitch point the two flanks move at different speeds along the tooth surface. The sliding velocity is (ω1 + ω2) times the distance of the contact point from P: zero at P and largest at the start or end of contact. It changes direction as contact passes through P, so friction on each flank reverses there too. In the interactive, at a pinion speed of 960 rpm, the default pair slides at up to 1.46 m/s.

Predict, then check

A 20-tooth pinion drives a 50-tooth wheel, both standard full-depth teeth. You change the pressure angle from 20° to 25° and keep everything else the same. The contact ratio

Worked examples

Path, arc and contact ratio · An 18-tooth pinion drives a 45-tooth wheel, module 5 mm, 20° pressure angle, standard addendum 1 module
  1. Pitch radii r = 5 × 18/2 = 45 mm and R = 5 × 45/2 = 112.5 mm; addendum radii 50 and 117.5 mm
  2. Base radii r cos 20° = 42.286 mm and R cos 20° = 105.715 mm
  3. Path of approach = √(117.5² − 105.715²) − 112.5 sin 20° = 12.811 mm
  4. Path of recess = √(50² − 42.286²) − 45 sin 20° = 11.29 mm
  5. Path of contact = 24.101 mm; arc of contact = 24.101/cos 20° = 25.648 mm
  6. Base pitch = π × 5 × cos 20° = 14.761 mm; contact ratio = 24.101/14.761 = 1.633
  7. Check: approach 12.811 mm is less than r sin φ = 15.391 mm, so no interference

Answer: Path of contact 24.1 mm, arc of contact 25.65 mm, contact ratio 1.633: one pair always in contact, two pairs for 63% of the time

Sliding velocity at the start and end of contact · A 24-tooth pinion at 1,200 rpm drives a 60-tooth wheel, module 3 mm, 20°, standard addendum
  1. ω1 = 2π × 1200/60 = 125.66 rad/s; ω2 = ω1 × 24/60 = 50.27 rad/s; pitch-line speed = ω1 × 36 mm = 4.524 m/s
  2. Path of approach = 7.903 mm; path of recess = 7.094 mm
  3. Sliding velocity at the first point of contact = (ω1 + ω2) × approach = 175.93 × 7.903 = 1,390 mm/s
  4. At the last point of contact = 175.93 × 7.094 = 1,248 mm/s
  5. At the pitch point the sliding velocity is zero: pure rolling

Answer: 1.39 m/s at the start and 1.248 m/s at the end of contact, zero at P

Effect of the pressure angle · A 20-tooth pinion and a 50-tooth wheel, module 4 mm, standard addendum, at 14.5°, 20° and 25°
  1. 14.5°: approach 12.948 mm, recess 10.873 mm, contact ratio 1.958
  2. But at 14.5° the approach exceeds r sin φ = 10.015 mm: the wheel tip reaches below the pinion's base circle (interference, next chapter)
  3. 20°: approach 10.36 mm (limit 13.681), contact ratio 1.656
  4. 25°: approach 8.749 mm (limit 16.905), contact ratio 1.473

Answer: Contact ratio falls from 1.96 to 1.66 to 1.47 as φ rises; 14.5° would interfere with these teeth, 20° and 25° do not

Chapter 13

Interference and undercutting: minimum number of teeth and how to avoid them

Which syllabus covers thisAU ME3491 Unit IIVTU BME503 Module 3SPPU 202047 Unit VMU MEC403 Module 6KTU PBMET404 Module 4

What is interference in involute gears?

The involute exists only outside the base circle. Below it, a tooth flank is just a radial fillet. The line of action touches the pinion's base circle at the interference point T1 (and the wheel's at T2). If the wheel's addendum circle cuts the line of action beyond T1, the wheel tip tries to keep contact below the pinion's base circle, where there is no involute to meet it. The tip then digs into the pinion's flank: the gears jam, wear fast or lose their constant velocity ratio. That is interference.

What is undercutting?

When a gear is generated by a rack cutter or a hob, the cutter is a stiff, full-depth rack rolling with the blank. If the blank has too few teeth, the cutter's tip line passes below the interference point and the cutter simply cuts away the root of each tooth. That avoids interference in service, but it costs twice. The tooth is thinned exactly where the bending stress is highest. The lowest part of the involute is also lost, so the contact ratio drops.

How many teeth must a pinion have to avoid interference?

Put the wheel's addendum circle exactly through T1 and solve for the pinion teeth. With gear ratio G = z2/z1, addendum A modules and pressure angle φ you get the formula below. It gives the fewest teeth for that ratio. A bigger wheel (larger G) needs a bigger pinion, up to the rack limit. In the interactive, a 14-tooth pinion on a 3:1 ratio at 20° needs 14.98, so 15 teeth. Equal gears (G = 1) need only 12.32, so 13.

Interference in involute gears: interference points, minimum teeth on the pinion and the rack limit: interactive loads as you scroll

What is the minimum number of teeth on a pinion that meshes with a rack?

For a rack, the addendum line must not pass T1, which sits r sin²φ inside the pitch line. With addendum A·m and r = zm/2 that gives z ≥ 2A/sin²φ. At 20° with A = 1: 2/sin²20° = 17.1, so 18 teeth strictly. KHK's gear reference quotes 17 as the minimum free of undercut: at 17 teeth T1 falls short of the tip line by only 0.0057 module. At 14.5° the limit is 31.9, so 32 teeth. At 25° it is 11.2, so 12.

How do designers avoid interference and undercut?

Four levers. Use more pinion teeth, which may mean a smaller module for the same diameter. Use a larger pressure angle: 25° allows 12 teeth on a rack instead of 18. Shorten the addendum, as stub teeth do, accepting a lower contact ratio. Or apply a positive profile shift: the cutter is withdrawn by x·m when the pinion is generated. That moves the tooth outward so the root is not cut away. A rack cutter needs x ≥ A − z sin²φ/2.

Predict, then check

A 15-tooth pinion with standard 20° full-depth teeth meshes with a rack and interferes. Which change removes the interference?

Worked examples

Minimum pinion teeth for a 4:1 reduction · A pinion drives a wheel with 4 times as many teeth, standard addendum 1 module; find the fewest pinion teeth at 20° and at 14.5°
  1. 20°: sin²20° = 0.11698; 1 + (1/4)(1/4 + 2) × 0.11698 = 1.0658; square root = 1.03238
  2. z_min = 2/(4 × (1.03238 − 1)) = 15.44, so 16 teeth
  3. 14.5°: the same formula gives 28.61, so 29 teeth
  4. Rack limits for comparison: 17.1 at 20° and 31.9 at 14.5°

Answer: 16 teeth at 20°, 29 teeth at 14.5°

Largest wheel addendum for a given pair · A 16-tooth pinion drives a 48-tooth wheel, module 3 mm, 20°; how large may the wheel's addendum be?
  1. In modules: r = 8, R = 24. The wheel's tip circle may just pass through T1
  2. O2T1 = √((R cos φ)² + ((r + R) sin φ)²) = √(22.553² + 10.945²) = 25.068 modules
  3. Largest wheel addendum = 25.068 − 24 = 1.068 modules = 3.204 mm
  4. The standard addendum is 1 module = 3 mm, below 3.2 mm, so the pair is clear

Answer: Up to 1.068 modules (3.2 mm); the standard 3 mm addendum does not interfere

Profile shift to stop undercut on a 12-tooth pinion · A 12-tooth pinion, module 2 mm, is generated by a standard 20° rack cutter (addendum line 1 module from its pitch line)
  1. Without shift: 12 < 2/sin²20° = 17.1, so the cutter undercuts
  2. The cutter's addendum line must stay outside T1, which lies r sin²φ = 6 × 0.11698 = 0.7019 modules inside the pitch line
  3. Least shift x = 1 − 0.7019 = 0.2981 (times the module)
  4. Withdraw the cutter by 0.298 × 2 = 0.596 mm
  5. Alternative: a 25° cutter needs no shift, since 12 is above the 25° limit of 11.2

Answer: Positive profile shift of at least 0.298 m = 0.6 mm, or a 25° cutter

Chapter 14

Simple, compound and reverted gear trains

Which syllabus covers thisAU ME3491 Unit IIVTU BME503 Module 3SPPU 202047 Unit VMU MEC403 Module 6KTU PBMET404 Module 4

How does a simple gear train work, and what do idlers do?

In a simple train every shaft carries one gear. Meshing gears share the same pitch-line speed, so n·z is the same for every gear, and the output speed is n_in × z_first/z_last. The idlers in between cancel out. They only fill the distance between the shafts and set the direction: each external mesh reverses the sense. In the interactive, a 1-2-3-4 row with 18 and 52 teeth at the ends gives 346.2 rpm from 1,000 rpm, reversed (three meshes), whatever the idlers have.

What makes a compound train different?

In a compound train an intermediate shaft carries two gears that turn together. The ratio then multiplies stage by stage: train value = (product of driver teeth)/(product of driven teeth). That gives a large reduction in a small space. A single 20:1 mesh from an 18-tooth pinion needs a 360-tooth wheel. Two stages of about 4.5:1 each do the job with wheels of about 80 teeth.

What is a reverted gear train?

A reverted train is a compound train folded back so that the output shaft lines up with the input shaft. A clock is one: the hour hand turns once for every 12 turns of the minute hand, on the same axis. Both stages must span the same centre distance. With one module that means z1 + z2 = z3 + z4. With different modules it means m1(z1 + z2) = m2(z3 + z4). Example: 20/60 at module 2 and 20/44 at module 2.5 both span 80 mm, for a ratio of 6.6.

Simple, compound and reverted gear trains: train value, output speed and equal centre distances: interactive loads as you scroll

How do you choose the teeth for a target ratio?

Split the ratio into stages of roughly equal size (about the square root for two stages) and keep every pinion above the interference limit, at least 18 teeth for 20° gears. Then search integers. Ratios that factor nicely, such as 20 = (80/18)(81/18), can be met exactly. For a reverted train the tooth sums must also match, which narrows the choice: with teeth from 18 to 100 there are 56 exact 12:1 reverted sets, and the smallest uses 99 teeth per stage.

Predict, then check

A simple gear train has a driver, one idler and a driven gear. You add a second idler between them. The output

Worked examples

Simple train with an idler · A motor pinion of 24 teeth at 1,440 rpm (illustrative) drives a 60-tooth gear through a 40-tooth idler
  1. Idler speed = 1440 × 24/40 = 864 rpm, opposite to the motor
  2. Output speed = 864 × 40/60 = 576 rpm = 1440 × 24/60: the idler cancels
  3. Two external meshes: the output turns the same way as the motor
  4. Without the idler (24 straight onto 60): still 576 rpm, but reversed

Answer: 576 rpm, same direction as the motor; the idler only changes direction and spacing

Compound train for a 20:1 reduction · Reduce 1,440 rpm to exactly 72 rpm in two stages, no gear below 18 teeth, smallest total number of teeth
  1. Train value needed = 72/1440 = 1/20
  2. Integer search for the smallest total teeth (each stage near √20 = 4.472): drivers 18 and 18, driven 80 and 81
  3. Check: (80 × 81)/(18 × 18) = 6480/324 = 20
  4. Stage ratios 4.444 and 4.5; intermediate shaft at 1440 × 18/80 = 324 rpm
  5. Output = 1440/20 = 72 rpm, same direction as the input (two external meshes)

Answer: 18→80 then 18→81 gives exactly 72 rpm

Reverted train for 12:1 (a clock's minute-to-hour reduction) · Input and output coaxial, one module of 1.5 mm for both stages, ratio exactly 12, all gears 18 to 100 teeth
  1. Conditions: (z2/z1)(z4/z3) = 12 and z1 + z2 = z3 + z4 = S
  2. Searching all sets: 56 solutions; the smallest tooth sum is S = 99
  3. z1 = 18, z2 = 81 (ratio 4.5); z3 = 27, z4 = 72 (ratio 2.667)
  4. Check: 4.5 × 2.667 = 12
  5. Centre distance = 1.5 × 99/2 = 74.25 mm for both stages

Answer: 18/81 and 27/72 teeth, both stages 74.25 mm apart, output in line with the input

Chapter 15

Epicyclic gear trains: the tabular method and holding torque

Which syllabus covers thisAU ME3491 Unit IIVTU BME503 Module 3SPPU 202047 Unit VMU MEC403 Module 6KTU PBMET404 Module 4

What is an epicyclic gear train?

In an epicyclic (planetary) train at least one gear axis moves. Planets mesh with a central sun and an internal annulus, and they ride on an arm (the carrier) that turns about the main axis. With one module the annulus has A = S + 2P teeth, because its pitch diameter spans the sun plus two planets. Three or more planets share the load; they can be equally spaced only if (S + A) divides by their number. Hold one member, drive another, and the third is the output.

How does the tabular method find the speeds?

Step 1: imagine the arm fixed and give the sun +1 turn. The planet turns −S/P and the annulus −S/A, like a simple train with the planet as an idler (the internal mesh keeps its sense). Step 2: multiply that row by x. Step 3: add y turns to every member, which turns the whole set as one block, so the arm turns y. Two conditions fix x and y: the held member's speed is zero and the input's is given. In the interactive, sun 24 and planet 18 with the annulus held give x = 714.3, y = 285.7.

Epicyclic gear train by the tabular method: output speed, output torque and the holding torque: interactive loads as you scroll

How are the output and holding torques found?

At steady speed, with friction neglected, two balances hold. The three external torques add to zero, because nothing else holds the set. And the power in equals the power out, because the held member does not move and so absorbs no power. So T_out = −T_in·n_in/n_out, and the holding torque is whatever the input and output leave over. With the annulus held, 100 N·m on the sun gives 350 N·m on the arm and needs 250 N·m on the annulus.

Is there a quicker way to see the torque split?

Yes: take a free body of one planet. At steady speed with no friction it carries a tooth force F from the sun, an equal force F from the annulus and 2F from its pin on the arm. Sun torque ∝ F·rS, annulus torque ∝ F·rA, arm torque ∝ −2F(rS + rP) = −F(rS + rA). With radii proportional to teeth: T_sun : T_ann : T_arm = S : A : −(S + A), whichever member is held. The arm always carries the largest torque, opposite to the other two.

Predict, then check

In a planetary set with the annulus held, the sun is driven with 100 N·m. The torque needed to hold the annulus is

Worked examples

Annulus held: reduction to the arm · Sun 30 teeth, planets 21 teeth, annulus held; the sun is driven at 1,500 rpm with 40 N·m
  1. Annulus teeth A = 30 + 2 × 21 = 72
  2. Table, arm fixed and sun +1: arm 0, sun +1, planet −30/21 = −1.4286, annulus −30/72 = −0.4167
  3. General row: arm y, sun x + y, planet y − 1.4286x, annulus y − 0.4167x
  4. Annulus held: y = 0.4167x; sun: x + y = 1500 → x = 1,058.82, y = 441.18
  5. Arm speed = y = 441.18 rpm, same sense as the sun; ratio 3.4 = 1 + A/S
  6. Planet: −1,071.43 rpm absolute, −1,512.61 rpm relative to the arm (what its bearing sees)
  7. Torques: arm (output) T = −40 × 1500/441.18 = −136 N·m; annulus T = −(40 − 136) = 96 N·m

Answer: Arm at 441.2 rpm delivering 136 N·m; holding torque on the annulus 96 N·m, in the same sense as the input torque

Sun held: overdrive from arm to annulus · The same set (S = 30, P = 21, A = 72) with the sun held; the arm is driven at 1,000 rpm with 200 N·m
  1. Sun held: x + y = 0; arm: y = 1000 → x = −1,000
  2. Annulus = y − (30/72)x = 1000 + 416.67 = 1,416.67 rpm, same sense as the arm
  3. Output torque on the annulus = −200 × 1000/1,416.67 = −141.18 N·m
  4. Holding torque on the sun = −(200 + (−141.18)) = −58.82 N·m
  5. Check S : A : −(S + A): −58.82 : −141.18 : 200 = 30 : 72 : −102

Answer: Annulus at 1,416.7 rpm (overdrive, ratio 0.706), 141.2 N·m out; sun needs 58.8 N·m to hold it

Arm held: a reversing train and the torque on its mounting · The same set with the arm held (bolted to the casing); the sun is driven at 600 rpm with 50 N·m
  1. Arm held: y = 0; sun: x = 600
  2. Annulus = −(30/72) × 600 = −250 rpm: reversed, 2.4:1 reduction
  3. Planet = −(30/21) × 600 = −857.1 rpm, spinning on fixed pins
  4. Output (annulus) torque = −50 × 600/(−250) = 120 N·m
  5. Torque on the arm's mounting = −(50 + 120) = −170 N·m

Answer: Annulus at 250 rpm reversed with 120 N·m; the casing must react 170 N·m on the arm

Chapter 16

Static force analysis: two- and three-force members, the four-bar and virtual work

Which syllabus covers thisAU ME3491 Unit IVVTU BME503 Module 2SPPU not in syllabusMU MEC503 Module 2KTU PCMET501 Module 1

What is static force analysis of a mechanism?

At low speed the inertia of the links is small next to the working loads, so each link can be treated as being in equilibrium in every position: ΣFx = 0, ΣFy = 0, ΣM = 0. Draw a free-body diagram of each moving link, with the pin forces as unknowns (equal and opposite on the two links that share a pin). A four-bar has three moving links, so 3 × 3 = 9 equations. The unknowns are four pin-force pairs (8) and the driving torque (1). Solving gives the torque to hold a load and the pin forces that size the pins and bearings.

What are two-force and three-force members?

A link loaded only at two pins, with no torque and no force in between, is a two-force member. Its two forces must be equal, opposite and along the line joining the pins, so only the magnitude is unknown. A link with three forces is a three-force member. Their lines meet at one point and the forces close a triangle. A link with forces at two pins plus a torque, like a crank, carries two equal, opposite, parallel forces that form a couple balancing the torque. With only a torque on the rocker the coupler is a two-force member. In the interactive at θ2 = 60° with T4 = 30 N·m, it carries 166 N.

How do you solve a four-bar for the input torque?

Start at the loaded end and use the two-force members to fix directions. With a torque T4 on the rocker, the coupler force acts along AB. Take moments about O4 to get its size, then carry it to the crank pin and take moments about O2 for T2. With a force on the coupler instead, the rocker becomes the two-force member: its force acts along O4B. Moments about A on the coupler give its size, and ΣF = 0 on the coupler gives the crank-pin force. The interactive solves all nine equations at once. At θ2 = 60° with 30 N·m on the rocker it needs T2 = 9.8 N·m.

Static force analysis of a four-bar: input torque for a load, pin forces and virtual work: interactive loads as you scroll

How does virtual work give the input torque without pin forces?

Frictionless pins do no work, so for any small movement the input work equals the output work: T2ω2 + T4ω4 + F·vP = 0 (torques and ω in the same sense). The input torque follows from velocities alone, for example from instantaneous centres. The mechanical advantage T4/T2 equals ω2/ω4: 3.06 at θ2 = 60° in the interactive. Near a toggle position the rocker momentarily stops (ω4 → 0), so a small input torque holds a very large output torque. Toggle clamps and stone crushers use exactly that.

Predict, then check

A four-bar holds a fixed torque on its rocker. As the crank moves towards the position where the rocker reverses (ω4 → 0), the input torque needed

Worked examples

Torque on the rocker: coupler as a two-force member · Four-bar: ground O2O4 = 300 mm, crank 100 mm, coupler 280 mm, rocker 200 mm (illustrative). Crank at θ2 = 90°; a clockwise torque of 40 N·m acts on the rocker. Links massless, pins frictionless
  1. Position: A = (0, 100) mm; B = (262.84, 196.52) mm; coupler at 20.16°, rocker at 100.71°
  2. The coupler is a two-force member: its force acts along AB. Perpendicular distance from O4 to line AB = 197.28 mm
  3. Rocker moments about O4: Fc × 0.19728 m = 40 N·m → Fc = 202.8 N (tension)
  4. Perpendicular distance from O2 to line AB = 93.87 mm, so T2 = 202.8 × 0.09387 = 19.03 N·m
  5. Pin forces: 202.8 N at every pin; transmission angle = 80.5°

Answer: T2 = 19.03 N·m counter-clockwise; coupler force 202.8 N

Force on the coupler: rocker as a two-force member · The same linkage at θ2 = 120°, no torque on the rocker, and a 500 N downward force at a coupler point P 120 mm along AB and 60 mm to its left
  1. A = (−50, 86.6), B = (213.8, 180.47), P = (42.94, 183.36) mm; rocker at 115.53°
  2. The rocker carries forces only at B and O4: its force on the coupler acts along O4B, size R unknown
  3. Coupler moments about A: R × 278.49 mm (distance from A to the line O4B) = 500 N × 92.94 mm (horizontal distance from A to P) → R = 166.9 N (the rocker pushes)
  4. Coupler ΣF = 0 gives the crank-pin force: (71.9, 349.4) N, size 356.8 N. Its line passes through the point where the other two lines meet (three-force member)
  5. Crank moments about O2: T2 = −23.7 N·m

Answer: Rocker force 166.9 N, crank-pin force 356.8 N, input torque 23.7 N·m clockwise

Input torque by virtual work and instantaneous centres · The same linkage at θ2 = 150° with 40 N·m clockwise on the rocker
  1. I24 lies where the line AB meets the ground line O2O4: x = −210.75 mm from O2
  2. ω4/ω2 = I12I24/I14I24 = −210.75/(−210.75 − 300) = 0.4126
  3. Virtual work: T2·ω2 = T4·ω4 (T4 clockwise, ω counter-clockwise positive) → T2 = 40 × 0.4126 = 16.505 N·m
  4. Mechanical advantage = ω2/ω4 = 2.423
  5. The two-force-member route of the first example gives the same torque

Answer: T2 = 16.51 N·m counter-clockwise; mechanical advantage 2.42

Chapter 17

Dynamic force analysis of the reciprocating engine: piston effort, crank effort and the equivalent two-mass rod

Which syllabus covers thisAU ME3491 Unit IVVTU BME503 Module 2SPPU not in syllabusMU MEC503 Module 2KTU PCMET501 Module 1

What force does the connecting rod actually pass to the crank?

Not the gas load alone. The gas pressure p on the piston area A gives the gas load F_L = pA, but part of it is spent accelerating the piston, rings, gudgeon pin and the small end of the rod (the reciprocating mass). The piston effort is F_P = F_L − m_R a. Take a 349 cc single (72 mm bore, 85.8 mm stroke) at 4000 rpm with 0.5 kg reciprocating and 30 bar on the piston at 30° after top dead centre: F_L = 12.21 kN, the inertia force is 3.74 kN, so F_P = 8.47 kN.

Forces in a single-cylinder engine: piston effort, rod thrust, side thrust and crankshaft torque: interactive loads as you scroll

How is the piston effort split into rod thrust, side thrust and crank torque?

The rod leans at the obliquity β, with sin β = sin θ / n and n = l/r. Its thrust is F_Q = F_P / cos β. The cylinder wall must supply the side thrust F_N = F_P tan β, which loads one side of the piston skirt harder than the other. At the crank pin, F_Q splits into a radial part F_Q cos(θ + β), which only loads the main bearings, and the crank effort F_T = F_Q sin(θ + β), which turns the shaft. In the example: β = 7.18°, F_Q = 8.54 kN, F_N = 1067 N and T = F_T r = 221.3 N·m.

When does the inertia force matter as much as the gas force?

At high speed. The inertia force grows with ω², so doubling the speed makes it four times larger. At top dead centre the piston acceleration is rω²(1 + 1/n). For the 0.5 kg reciprocating mass at 6100 rpm (this engine's maximum-power speed) that is 10.94 kN, the same as 26.9 bar on the piston. Near TDC it takes force away from the crank, and near bottom dead centre it gives it back. Over a whole turn at steady speed the inertia torque averages to zero: it only reshapes the turning moment diagram.

How is a connecting rod replaced by two point masses, and what is the correction couple?

Two masses are dynamically equivalent to the rod if they match its mass, its CG and its moment of inertia. With one mass at the small end, p from the CG, the other must sit l2 = k²/p beyond the CG. For convenience the second mass is moved to the big-end pin. That keeps the mass and the CG, but the moment of inertia becomes m·p·q instead of m·k². The error, m(k² − pq)α, is put back as a correction couple, and it reaches the crankshaft multiplied by dβ/dθ = cos θ/√(n² − sin²θ).

Predict, then check

An engine's speed is raised from 4000 to 8000 rpm. The inertia force of the reciprocating parts at top dead centre

Worked examples

Forces 30° after top dead centre · 349 cc single: bore 72 mm, stroke 85.8 mm (r = 42.9 mm); rod ratio n = 4 (illustrative); reciprocating mass 0.5 kg (illustrative); 4000 rpm; net gas pressure 30 bar (illustrative) at θ = 30°
  1. A = π × 0.072²/4 = 40.715 cm²; F_L = 30 × 10⁵ × 0.004072 = 12215 N
  2. ω = 2π × 4000/60 = 418.88 rad/s; exact a = rω²[cos θ + (n² cos 2θ + sin⁴θ)/(n² − sin²θ)^1.5] = 7490 m/s²
  3. F_I = 0.5 × 7490 = 3745 N; F_P = 12215 − 3745 = 8470 N
  4. sin β = sin 30°/4 → β = 7.181°; F_Q = F_P/cos β = 8537 N; F_N = F_P tan β = 1067 N
  5. F_T = F_Q sin(θ + β) = 5159 N; T = F_T × 0.0429 = 221.3 N·m
  6. Without the inertia force the torque would be 319.2 N·m

Answer: F_P = 8.47 kN, F_Q = 8.54 kN, side thrust 1067 N, torque 221.3 N·m

Inertia force at the maximum-power speed · Same engine at 6100 rpm (its quoted maximum-power speed), n = 4, reciprocating mass 0.5 kg
  1. ω = 2π × 6100/60 = 638.79 rad/s; rω² = 0.0429 × 638.79² = 17505 m/s²
  2. At TDC the exact and two-term forms agree: a = rω²(1 + 1/4) = 21882 m/s² (2231 g)
  3. F_I = 0.5 × 21882 = 10941 N, equal to 26.9 bar on the 40.72 cm² piston
  4. At θ = 90°: exact a = −rω²/√(n² − 1) = −4520 m/s²; the two-term form gives −rω²/n = −4376 m/s², 3.2 % larger in size

Answer: 10.94 kN at TDC: about 27 bar of the gas pressure goes into accelerating the piston

Two-mass rod and its correction couple · Rod 0.9 kg, centre length 171.6 mm (n = 4), CG 112 mm from the small end, k = 55 mm about the CG (all illustrative); 4000 rpm, θ = 60°
  1. Dynamically equivalent: l2 = k²/p = 55²/112 = 27.01 mm; masses 0.175 kg at the small end and 0.725 kg at l2 beyond the CG
  2. Practical pair at the pins: q = 59.6 mm; small end 0.9 × 59.6/171.6 = 0.313 kg, big end 0.587 kg
  3. Moment of inertia error: m(k² − pq) = 0.9 × (0.055² − 0.112 × 0.0596) = −3.285 × 10⁻³ kg·m²
  4. Rod angular acceleration αc = −ω² sin θ (n² − 1)/(n² − sin²θ)^1.5 = −38273 rad/s²
  5. Correction couple = −(k² − pq)·m·αc = −125.73 N·m; on the crankshaft × cos θ/√(n² − sin²θ) = 0.128 → −16.1 N·m (against the rotation at this instant)

Answer: Correction torque on the crankshaft −16.1 N·m at 60°

Chapter 18

Centrifugal governors: Watt, Porter and Proell

Which syllabus covers thisAU not in syllabusVTU BME503 Module 4SPPU not in syllabusMU MEC503 Module 1KTU PCMET501 Module 3

What does a governor do, and why did the Watt governor fall out of use?

A governor holds the mean speed of an engine as the load changes, by moving the fuel or steam control through its sleeve. A flywheel only smooths the speed within one cycle. In the Watt governor the spinning balls settle where gravity and the centrifugal force balance, at a height h = g/ω² below the pivot: h = 895/N² m with N in rpm. That is 248 mm at 60 rpm but only 9.9 mm at 300 rpm. At higher speeds the height hardly changes, so the sleeve barely moves.

How does the heavy sleeve of a Porter governor change the speed?

The Porter adds a heavy central load M on the sleeve, carried by the lower links. With equal arms and links pivoted on the axis, taking moments about the instantaneous centre of a lower link gives ω²h = g(m + M)/m, with ± the sleeve friction f added to Mg. With 250 mm arms, 4 kg balls and a 30 kg sleeve (all illustrative), the speed between the stops (30° and 45° arm angle) runs from 187.4 to 207.4 rpm. A Watt governor of the same size would run at 64.3 to 71.1 rpm.

Watt, Porter and Proell governors: equilibrium speed against height, range of speed and sleeve lift: interactive loads as you scroll

What does the Proell governor change?

The balls are not at the arm joints. They sit on extensions of the lower links, here 0.15 of the arm length and parallel to the axis at the mid position. The centrifugal force then acts higher above the instantaneous centre and has more leverage, so the governor runs slower for the same arms and loads. At mid travel it runs at 179.6 rpm against the Porter's 195.8 rpm. Its speed range is also narrower, 4.8 % against 10.1 %, so it is more sensitive. Lengthen the extension to 0.2 of the arm and the speed falls just above the lower stop: unstable.

What are friction insensitiveness, effort and power?

Sleeve friction f must be overcome before the sleeve moves, so at each height there is a band of speeds with no response. With f = 15 N at the lower stop of the example governor, the band is 183.1 to 191.6 rpm, a coefficient of insensitiveness of 4.5 %. Effort is the mean force the sleeve can exert for a given fractional change of speed. Power is that effort times the sleeve's travel. For a 1 % speed rise at mid travel: effort 3.35 N, travel 7.82 mm, power 26.2 mJ.

Predict, then check

The Porter governor above (4 kg balls) has its 30 kg sleeve replaced by a 60 kg sleeve. At the same height the equilibrium speed

Worked examples

Speed range and sleeve lift of a Porter governor · Arms and links 250 mm, all pivoted on the axis; balls 4 kg each; sleeve 30 kg; stops at 30° and 45° arm angle from the axis (all illustrative); no friction
  1. Heights: h1 = 0.25 cos 30° = 216.5 mm, h2 = 0.25 cos 45° = 176.8 mm
  2. N² = 895 × (m + M)/(m h): N1 = √(895 × 34/(4 × 0.2165)) = 187.4 rpm
  3. N2 = √(895 × 34/(4 × 0.1768)) = 207.4 rpm
  4. Range of speed = 20 rpm (10.1 % of the mean)
  5. Sleeve lift = 2(h1 − h2) = 79.5 mm

Answer: 187.4 to 207.4 rpm, sleeve lift 79.5 mm

Effect of sleeve friction · The same governor at its lower stop (h = 216.5 mm), sleeve friction 15 N
  1. Speed falling (friction holds the sleeve up): ω² = (mg + Mg − f)/(m h) = (39.24 + 294.3 − 15)/(4 × 0.2165) → N = 183.1 rpm
  2. Speed rising (friction resists the lift): ω² = (39.24 + 294.3 + 15)/(4 × 0.2165) → N = 191.6 rpm
  3. Frictionless speed 187.4 rpm; coefficient of insensitiveness = (191.6 − 183.1)/187.4 = 4.5 %

Answer: The sleeve stays put between 183.1 and 191.6 rpm

Proell against Porter at mid travel · Same arms, balls and sleeve; the Proell balls on extensions 0.15 × 250 = 37.5 mm long, parallel to the axis at the mid angle 37.5°
  1. h = 0.25 cos 37.5° = 198.3 mm; Porter: N = √(895 × 34/(4 × 0.1983)) = 195.8 rpm
  2. Proell, moments about the instantaneous centre with the extension vertical: ω²(h + e) = g(m + M)/m
  3. N = √(895 × 34/(4 × 0.2358)) = 179.6 rpm
  4. Between the stops the Proell runs 177 to 185.7 rpm, a range of 4.8 %

Answer: 179.6 rpm against 195.8 rpm; range 4.8 % against 10.1 %

Chapter 19

Spring-loaded governors: Hartnell, controlling force, stability, isochronism, effort and power

Which syllabus covers thisAU not in syllabusVTU BME503 Module 4SPPU not in syllabusMU MEC503 Module 1KTU PCMET501 Module 3

How does a Hartnell governor balance the balls against a spring?

Each ball rides on the vertical arm (length a) of a bell crank pivoted on the rotating frame. The horizontal arm (length b) presses on the sleeve, and a compressed spring pushes the sleeve back. With the arms taken vertical and horizontal, moments about the pivot give F_c·a = (S + Mg)b/2. With 2 kg balls, a = 120 mm, b = 80 mm and a 4 kg sleeve (illustrative), running at 300 rpm at a 100 mm radius and 320 rpm at 130 mm: spring stiffness 14.19 N/mm, initial compression 39 mm.

Hartnell governor: spring stiffness, controlling force curve, stability, isochronism and sensitiveness: interactive loads as you scroll

What does the controlling force curve say about stability?

The controlling force is the inward force on each ball at equilibrium, F = mω²r, plotted against the radius r. Since ω² = F/(mr), the speed rises with radius when F/r rises. That is the stable case: on a straight line it means the line, extended back, cuts the force axis below the origin. A line through the origin keeps F/r constant: one speed at every radius, isochronous. A line cutting above the origin is unstable. For the example governor the intercept is −117.9 N: stable.

Why not make a governor as sensitive as possible?

Sensitiveness compares the range of speed with the mean speed, (N2 − N1)/N_mean. The example has 6.45 %; the smaller the figure, the more sensitive the governor. The limit is isochronism. Here the same 300 rpm at 100 mm would need a spring of 8.88 N/mm with 62.2 mm initial compression. An isochronous governor has no single equilibrium radius at its speed. A small speed change sends the sleeve from stop to stop, the fuel supply over-corrects and the speed swings to and fro. This is hunting, so practical governors keep a small, stable speed range.

How are the effort and power of a Hartnell governor found?

Let the speed rise by a fraction c while the sleeve is held. Each ball's force grows by ((1 + c)² − 1)F, and through the bell cranks the sleeve force needed to hold it is 2(a/b) times that. The effort is the mean, half of it. Power is effort times the sleeve travel to the new equilibrium. For a 1 % rise at the lower stop of the example: effort 5.95 N, travel 2.32 mm, power 13.8 mJ.

Predict, then check

The example Hartnell governor (300 rpm at 100 mm) is fitted with a spring twice as stiff, set to the same force at the lower stop. The speed at the outer stop (130 mm)

Worked examples

Spring for a Hartnell governor · Balls 2 kg; ball arm a = 120 mm, sleeve arm b = 80 mm; sleeve 4 kg; 300 rpm at r1 = 100 mm, 320 rpm at r2 = 130 mm (all illustrative)
  1. F1 = mω1²r1 = 2 × 31.416² × 0.1 = 197.4 N; F2 = 2 × 33.51² × 0.13 = 292 N
  2. S = 2F·a/b − Mg: S1 = 2 × 197.4 × 1.5 − 39.24 = 552.9 N; S2 = 836.7 N
  3. Sleeve lift = (r2 − r1) b/a = 30 × 80/120 = 20 mm
  4. Stiffness s = (836.7 − 552.9)/20 = 14.19 N/mm; initial compression = S1/s = 39 mm
  5. Check by bisection: with this spring the balance holds at 100.0 mm for 300 rpm and 130.0 mm for 320 rpm; at 115 mm the speed is 311.5 rpm

Answer: s = 14.19 N/mm, initially compressed 39 mm

Isochronous and unstable springs · Same governor, same spring force at r1 (552.9 N), stiffness changed
  1. Isochronous: F/r constant, so F at 130 mm = 197.4 × 1.3 = 256.6 N, S = 730.6 N
  2. s = 2(a/b)²F1/r1 = 2 × 2.25 × 197.4/0.1 = 8.88 N/mm (initial compression 62.2 mm)
  3. Softer, 8 N/mm: S2 = 552.9 + 8 × 20 = 712.9 N, F2 = (S2 + Mg) b/(2a) = 250.7 N
  4. N2 = √(250.7/(2 × 0.13)) × 60/2π = 296.5 rpm, below 300 rpm; intercept of the F line +19.6 N

Answer: 8.88 N/mm gives isochronism; 8 N/mm is unstable (296.5 rpm at the outer stop)

Effort and power for a 1 % speed rise · The 14.19 N/mm governor at its lower stop (r = 100 mm, 300 rpm)
  1. Extra ball force = ((1.01)² − 1) × 197.4 = 3.968 N
  2. Sleeve force to hold it = 2(a/b) × that = 11.9 N; effort = half = 5.95 N
  3. New equilibrium: F0 + slope·r = m((1.01)ω1)²r with F0 = −117.9 N, slope = 3152.4 N/m → r = 103.48 mm
  4. Sleeve travel = (103.48 − 100) × 80/120 = 2.323 mm; power = 5.95 × 0.002323 = 13.8 mJ

Answer: Effort 5.95 N, power 13.8 mJ (N·m × 10⁻³)

Chapter 20

The gyroscopic couple: ships, aeroplanes and vehicles on a curve

Which syllabus covers thisAU ME3491 Unit VVTU not in syllabusSPPU 402042 Unit 2MU MEC503 Module 1KTU PCMET501 Module 2

Where does the gyroscopic couple come from?

A spinning rotor carries angular momentum L = Iω along its axis. Turning that axis at a precession rate ωp swings L round. Its rate of change, the vector ωp × L of size Iωωp, must be supplied as a couple by the bearings. The rotor pushes back on the vehicle with the opposite reaction couple, and that reaction is what tilts a ship's bow or a vehicle's body. An 8 t turbine rotor with k = 0.6 m at 3000 rpm has I = 2,880 kg·m². Turned at 0.023 rad/s, it needs 20.9 kN·m.

What does the gyroscopic couple do to a ship when it steers and when it pitches?

Take x forward, y to port and z up, with the turbine rotor turning clockwise seen from the stern, so the spin vector points forward (+x). Steering to port is precession about +z. The reaction couple −(ωp × L) points along −y, and a rotation about −y lifts the bow. So the bow rises and the stern dips, and steering to starboard does the opposite. When pitching, the precession is about the y axis. With the bow rising, the reaction couple is about −z, which swings the ship to starboard. Reverse the spin and every effect reverses.

Gyroscopic couple on a ship, an aeroplane and a two-wheeler on a curve: size and what it does: interactive loads as you scroll

How big is the gyroscopic couple on a propeller aircraft in a turn?

Same rule, with the engine and propeller as the rotor. With the propeller turning clockwise seen from the pilot's seat, a turn to the left lifts the nose and a turn to the right drops it. Take an illustrative 150 kg rotating assembly with k = 0.35 m at 2400 rpm, in a standard-rate turn of 3° per second (360° in two minutes). The couple is 18.375 × 251.3 × 0.0524 = 242 N·m. Small, but it acts in every turn, and it grows with the rotor's inertia, its speed and the rate of turn.

Why does a motorcycle lean further into a turn than the centrifugal force alone requires?

Both wheels spin about an axle pointing to the left (y), and in a left turn that axis precesses about z. The reaction couple, from the cross product, tries to tip the bike outwards, the same way as the centrifugal couple. So the rider leans in until gravity balances both: tan θ = (v²/gR)(1 + (2I_w + G I_e)/(m h r_w)). Take a 191 kg motorcycle with a 75 kg rider at 60 km/h on a 60 m radius (wheel and engine inertias illustrative): heel 25.82°, against 25.26° without the gyroscopic term.

Predict, then check

A ship's turbine rotor turns clockwise seen from the stern. The ship steers to starboard (right). The gyroscopic reaction makes the bow

Worked examples

Ship turning to port · Turbine rotor 8 t, radius of gyration 0.6 m, 3000 rpm clockwise seen from the stern; ship at 18 knots on a 400 m radius turn to port (all illustrative)
  1. I = 8000 × 0.6² = 2,880 kg·m²; ω = 2π × 3000/60 = 314.16 rad/s
  2. v = 18 × 1852/3600 = 9.26 m/s; ωp = v/R = 9.26/400 = 0.02315 rad/s
  3. C = Iωωp = 2,880 × 314.16 × 0.02315 = 20,946 N·m
  4. Spin +x, precession +z: ωp × L along +y; reaction on the hull along −y, which lifts the bow

Answer: 20.95 kN·m; the bow rises and the stern dips

Ship pitching · The same rotor; the ship pitches with an amplitude of 5° and a period of 12 s (simple harmonic, illustrative)
  1. θ = θ0 sin(2πt/T); the greatest pitching rate ωp = θ0 × 2π/T = 0.08727 × 2π/12 = 0.04569 rad/s, as the hull passes level
  2. Greatest couple = 2,880 × 314.16 × 0.04569 = 41,342 N·m
  3. Bow rising: precession about −y; ωp × L along +z, reaction along −z: the bow swings to starboard
  4. Half a period later the bow falls and the bow swings to port: the couple alternates every half period

Answer: Up to 41.3 kN·m; bow rising → it swings to starboard

Motorcycle on a curve · Motorcycle 191 kg (kerb) + rider 75 kg = 266 kg, CG 0.6 m up; tyres 100/90-19 and 140/70-17; each wheel I = 0.6 kg·m²; engine rotating parts 0.012 kg·m² geared 8:1 to the wheel, same sense; 60 km/h on a 60 m radius left turn (inertias, CG, rider and gear ratio illustrative)
  1. Rolling radii: 19 × 25.4/2 + 0.9 × 100 = 331.3 mm, 17 × 25.4/2 + 0.7 × 140 = 313.9 mm; mean 322.6 mm
  2. v = 16.667 m/s; wheel ω = v/r = 51.66 rad/s; ωp = v/R = 0.2778 rad/s
  3. Effective I = 2 × 0.6 + 8 × 0.012 = 1.296 kg·m²; gyro couple (upright) = 18.6 N·m; centrifugal couple (upright) = 266 × 4.63 × 0.6 = 739 N·m
  4. tan θ = (277.78/(9.81 × 60)) × (1 + 1.296/(266 × 0.6 × 0.3226)) = 0.4838 → θ = 25.82° (bisection on the moment balance agrees)
  5. At that heel: gyro couple 16.7 N·m and centrifugal couple 665 N·m, both outwards

Answer: Lean 25.82° into the turn (0.55° more than the centrifugal force alone needs)

Chapter 21

Balancing of rotating masses in one plane and in several planes

Which syllabus covers thisAU ME3491 Unit VVTU BME503 Module 4SPPU 402042 Unit 1MU MEC503 Module 6KTU PCMET501 Module 2

Why does a small unbalanced mass matter at speed?

A mass m at radius r turning at ω needs a centripetal force m r ω², and the bearings supply it, so they feel a force that turns with the shaft. It grows with the square of speed. A 20 g lump of dirt at 150 mm on a fan blade at an illustrative 1440 rpm (a 4-pole motor on India's 50 Hz supply turns a little below its 1500 rpm synchronous speed) pulls with 68.2 N; at twice the speed it pulls four times as hard. That rotating force shakes the frame once per revolution, loosens fasteners and shortens bearing life.

How do you balance several masses that all lie in one plane?

Draw each mass as a vector m·r pointing along its radius and add the vectors head to tail. If they do not close, the gap is the unbalance: one balancing mass whose m·r equals the gap and points along the closing side brings the centre of mass back onto the axis. This is static balance: the rotor will now rest in any position on knife edges. You pick the balancing radius and the mass follows from m·r. For thin rotors such as a pulley, a fan disc or a grinding wheel this is enough.

Why are two balancing planes needed when masses lie in different planes?

Masses spread along a shaft can have zero force sum and still form a couple that rocks the shaft end to end: static balance without dynamic balance. Two conditions must hold: Σ m r = 0 and Σ m r l = 0. Take moments about one balancing plane L so that its unknown mass drops out. The couple polygon (vectors m·r·l) then gives the mass in plane M, and the force polygon gives the mass in L. In the interactive's three-mass preset this needs 3.6 kg at 212° in L and 1.34 kg at 316° in M, at 100 mm.

Balancing several rotating masses in different planes: couple and force polygons and the balancing masses: interactive loads as you scroll

How balanced is balanced enough?

No rotor is perfect, so ISO 21940-11 sets a permissible residual unbalance by balance quality grade G, the product of the allowed mass-centre offset e and the service angular velocity ω in mm/s. Fans and general process machinery are typically G 6.3, standard electric motors and pumps G 2.5. A 25 kg fan rotor at 1440 rpm and G 6.3 may keep e = 6300/ω = 41.8 µm, or 1044 g·mm of unbalance in total. Rotors are balanced on a balancing machine or in place with trial weights.

Predict, then check

Two equal masses at equal radii sit 180° apart, but in planes 300 mm apart along the shaft. The shaft is

Worked examples

Three masses in one plane · An illustrative disc carries 2 kg at 100 mm (0°), 1.5 kg at 150 mm (90°) and 3 kg at 80 mm (210°). Find the balancing mass at 120 mm
  1. m·r values: 200, 225 and 240 kg·mm
  2. Horizontal sum: 200 cos 0° + 225 cos 90° + 240 cos 210° = −7.85 kg·mm
  3. Vertical sum: 200 sin 0° + 225 sin 90° + 240 sin 210° = 105 kg·mm
  4. Resultant = √((−7.85)² + 105²) = 105.3 kg·mm, at 94.3°
  5. The balancing mass points the opposite way, at 274.3°: m = 105.3/120 = 0.877 kg

Answer: 0.877 kg at 120 mm, at 274.3°

Two-plane balance of three masses · The interactive's preset: A 4 kg at 120 mm, 0°, 100 mm from plane L; B 3 kg at 150 mm, 100°, 250 mm; C 2.5 kg at 100 mm, 220°, 400 mm. Balancing planes L (0) and M (500 mm), balancing radius 100 mm; bearings at −50 and 550 mm
  1. m·r·l about L, in kg·mm·m: A 480 × 0.1 = 48, B 450 × 0.25 = 112.5, C 250 × 0.4 = 100
  2. Couple polygon: the closing side is the couple of the mass in M: (m·r)M × 0.5 = 66.9 kg·mm·m, so (m·r)M = 133.9 kg·mm at 316°
  3. Force polygon with the mass in M included: the closing side is (m·r)L = 360.4 kg·mm at 211.7°
  4. At 100 mm: 3.604 kg in L and 1.339 kg in M (taking moments about M instead gives the same mass in L)
  5. Before balancing at 1440 rpm the bearings carry rotating loads of 7.45 kN and 2.7 kN; after, both are zero

Answer: 3.6 kg at 211.7° in L and 1.34 kg at 316° in M, both at 100 mm

How much unbalance a fan may keep · An illustrative 25 kg fan rotor running at 1440 rpm, balance grade G 6.3 (ISO 21940-11 as summarised by a public source), correction planes on the two sides, correction radius 200 mm
  1. ω = 2π × 1440/60 = 150.8 rad/s
  2. Permissible offset e = G/ω = 6300/150.8 = 41.78 µm (g·mm per kg)
  3. Permissible residual unbalance U = e × M = 41.78 × 25 = 1044 g·mm
  4. For a rotor with its centre of mass midway between the planes, half per plane: 522 g·mm
  5. At 200 mm that is 522/200 = 2.61 g per plane

Answer: About 1044 g·mm in total, roughly 2.6 g at 200 mm in each plane

Chapter 22

Balancing of reciprocating masses: primary and secondary forces and multi-cylinder inline engines

Which syllabus covers thisAU ME3491 Unit VVTU BME503 Module 4SPPU 402042 Unit 1MU MEC503 Module 6KTU PCMET501 Module 2

What are the primary and secondary unbalanced forces?

The piston and the reciprocating part of the rod accelerate back and forth, so the frame feels a shaking force along the cylinder axis of about m r ω² (cos θ + cos 2θ/n), n = l/r. The first part, at engine speed, is the primary force. The second, at twice engine speed and 1/n as large, is the secondary force: it acts like a crank of radius r/4n turning at 2ω. For an illustrative cylinder with 1.2 kg reciprocating, r = 45 mm and n = 3.6 at 3000 rpm, the peaks are 5.33 kN and 1.48 kN.

Why can a single-cylinder engine only be partly balanced?

A counterweight on the crank web opposite the pin can cancel a fraction c of the primary force along the cylinder axis, but it rotates, so it adds c m r ω² sin θ across the axis. You trade a vertical shake for a horizontal one. With c = 1/2 the leftover force has the same size, m r ω²/2, in every direction: 2.66 kN in the example engine at 3000 rpm. The rotating masses (crank pin, big end) are balanced fully in addition, and the secondary force is not touched.

How are the cranks of an inline engine checked for balance?

Treat each cylinder's primary force as a crank vector m·r at its actual crank angle, and each secondary force as a vector (m r/n) at twice the crank angle. Primary force balance needs the crank vectors to sum to zero; primary couple balance needs the vectors times their distance from a reference plane to sum to zero. Repeat both with the doubled angles for the secondary. Each harmonic has its own force and couple polygon, exactly as for rotating masses. The interactive draws both crank diagrams and the exact shaking force.

Inline engine balance: unbalanced primary and secondary forces and couples for each crank arrangement: interactive loads as you scroll

Which unbalances do the common crank arrangements leave?

Twin with cranks at 180°: no primary force but a primary couple, plus a secondary force of 2 m r ω²/n. Three cylinders at 120°: primary and secondary forces cancel, but both couples remain (831 and 231 N·m for the example engine at 3000 rpm and 90 mm pitch). Four-cylinder flat crank 0-180-180-0: primary force and couple cancel, but all four secondary cranks line up, leaving 4 m r ω²/n at twice engine speed. Inline six: primary and secondary forces and couples all cancel. In a 90° V-twin the two primary forces combine into a constant force turning with the crank, which a crank counterweight can cancel.

Predict, then check

An inline four with a flat crank (0°, 180°, 180°, 0°). Which unbalance is left?

Worked examples

Primary and secondary forces of a single cylinder · Illustrative engine: reciprocating mass 1.2 kg, crank radius 45 mm, rod 162 mm (n = 3.6), 3000 rpm; counterweight at 50 mm balancing half the reciprocating mass
  1. ω = 2π × 3000/60 = 314.16 rad/s; m r ω² = 1.2 × 0.045 × 314.16² = 5329.6 N
  2. Peak primary force = 5330 N; peak secondary force = 5329.6/3.6 = 1480 N
  3. At θ = 30°: primary 5329.6 × cos 30° = 4616 N, secondary 5329.6/3.6 × cos 60° = 740 N, total 5356 N; the exact slider-crank gives 5385 N, the small rest being 4th-order terms
  4. Counterweight for c = 1/2: m = 0.5 × 1.2 × 45/50 = 0.54 kg at 50 mm
  5. Leftover primary force: 0.5 × 5329.6 = 2665 N, the same in every direction

Answer: Primary 5.33 kN and secondary 1.48 kN peaks; with half balancing, a constant 2.66 kN rotating residual

Secondary force of an inline four · Four cylinders, flat crank 0-180-180-0, each with the illustrative 1.2 kg, r = 45 mm, n = 3.6, running at 4000 rpm
  1. ω = 418.88 rad/s; m r ω² = 9474.8 N
  2. Primary cranks at 0°, 180°, 180°, 0°: vectors +1, −1, −1, +1 sum to 0; couples about the centre (−1.5p, −0.5p, +0.5p, +1.5p) × (+1, −1, −1, +1) sum to 0
  3. Secondary cranks at 0°, 360°, 360°, 0°: all point the same way
  4. Secondary force = 4 × 9474.8/3.6 = 10528 N, at 2 × 4000/60 = 133.3 Hz
  5. Secondary couple: (−1.5 − 0.5 + 0.5 + 1.5)p = 0

Answer: Only a secondary force of 10.53 kN at 133.3 Hz remains

Couples of a three-cylinder engine · Three cylinders 90 mm apart, cranks at 0°, 120°, 240°, the illustrative cylinder data, 3000 rpm; reference plane through the middle cylinder
  1. Primary force: three unit vectors 120° apart sum to 0. Secondary cranks at 0°, 240°, 480° = 120° also sum to 0
  2. Primary couple vectors: cylinder 1 at −90 mm, angle 0°; cylinder 3 at +90 mm, angle 240°
  3. |−1 + (cos 240° + i sin 240°)| = |−1.5 − 0.866i| = √3, so primary couple = √3 × 5329.6 × 0.09 = 830.8 N·m
  4. Secondary: |−1 + (cos 120° + i sin 120°)| = √3, so secondary couple = 830.8/3.6 = 230.8 N·m

Answer: Forces balanced; primary couple 831 N·m and secondary couple 231 N·m remain

Chapter 23

Free vibration: natural frequency, damping ratio and logarithmic decrement

Which syllabus covers thisAU ME3491 Unit VVTU BME503 Module 5SPPU 402042 Unit 3MU MEC503 Modules 3-4KTU PCMET501 Module 4

What sets the natural frequency of a spring and mass?

Displace the mass and let go: the spring force −kx accelerates it back, it overshoots, and it oscillates at ωn = √(k/m) rad/s, fn = ωn/2π. A stiffer spring raises the frequency, a heavier mass lowers it, both as a square root. Because the static deflection under the weight is δ = mg/k, fn = (1/2π)√(g/δ): a system that sags 1 mm under its own weight vibrates at 15.76 Hz, whatever its mass. In a vertical system gravity only shifts the equilibrium; it does not change fn.

How do real structures reduce to one equivalent spring?

Ask how much force (or torque) gives unit deflection (or twist) at the mass. A cantilever with a tip mass: k = 3EI/L³. A shaft twisting under a disc: k_t = GJ/L, with J = πd⁴/32, and the disc's inertia mR²/2 takes the place of mass. Springs side by side add (20 and 30 kN/m give 50 kN/m); springs end to end add as reciprocals (12 kN/m). Doubling a shaft's diameter makes it 16 times stiffer and raises fn four times.

Free vibration of a spring-mass system: natural frequency, damping ratio and logarithmic decrement: interactive loads as you scroll

What do under-, critically and over-damped mean?

A viscous damper adds a force −c·ẋ. Compare c with the critical value cc = 2√(km) = 2mωn: the damping ratio ζ = c/cc. Below 1 (underdamped) the mass oscillates at ωd = ωn√(1 − ζ²) inside an envelope that shrinks as e^(−ζωn t). At exactly 1 (critically damped) it returns to rest fastest without crossing zero. Above 1 (overdamped) it creeps back more slowly. Machine structures are lightly damped, often ζ of a few per cent; door closers and instrument needles are made close to critical.

How is damping measured from a decaying vibration?

Strike the structure and record the peaks. Successive peaks one damped period apart fall by a constant ratio, and its natural log is the logarithmic decrement δ = ln(x1/x2) = 2πζ/√(1 − ζ²), so ζ = δ/√(4π² + δ²). Over n cycles use δ = (1/n) ln(x0/xn) to average out noise. Dry (Coulomb) friction behaves differently: the amplitude falls by the same amount, 4F/k, every cycle, a straight-line decay; 10 N of friction on a 40 kN/m spring loses 1 mm per cycle.

Predict, then check

You double the mass on a spring and leave the spring alone. The natural frequency

Worked examples

Cantilever with a tip mass · A 20 mm square steel bar (E = 207 GPa, typical) clamped as a 500 mm cantilever carries an illustrative 10 kg instrument at its tip; neglect the bar's mass
  1. I = b⁴/12 = 0.02⁴/12 = 1.3333 × 10⁻⁸ m⁴
  2. k = 3EI/L³ = 3 × 207 × 10⁹ × 1.3333 × 10⁻⁸/0.5³ = 66240 N/m
  3. ωn = √(66240/10) = 81.39 rad/s; fn = 12.95 Hz
  4. Check by static deflection: δ = 10 × 9.807/66240 = 1.48 mm; fn = (1/2π)√(g/δ) = 12.95 Hz
  5. Adding 33/140 of the bar's 1.57 kg (density 7850 kg/m³) to the tip lowers fn to 12.72 Hz

Answer: k = 66.2 kN/m, fn = 12.95 Hz (12.72 Hz with the bar's own mass)

Torsional vibration of a shaft and disc · A steel shaft (G = 79.3 GPa, typical) 20 mm in diameter and 600 mm long, fixed at the top, carries an illustrative 20 kg disc of radius 150 mm
  1. J = πd⁴/32 = π × 0.02⁴/32 = 1.5708 × 10⁻⁸ m⁴
  2. k_t = GJ/L = 79.3 × 10⁹ × 1.5708 × 10⁻⁸/0.6 = 2076.1 N·m/rad
  3. Disc inertia I = mR²/2 = 20 × 0.15²/2 = 0.225 kg·m²
  4. ωn = √(2076.1/0.225) = 96.06 rad/s; fn = 15.29 Hz
  5. A 40 mm shaft would be 16 times stiffer: fn = 61.2 Hz

Answer: k_t = 2076 N·m/rad, fn = 15.29 Hz

Damping from a rap test · An illustrative 10 kg mass on a 40 kN/m spring is tapped; the record shows a peak of 8.0 mm and, five cycles later, 2.1 mm
  1. δ = (1/5) ln(8.0/2.1) = 0.2675
  2. ζ = δ/√(4π² + δ²) = 0.0425, about 4.3 %
  3. cc = 2√(km) = 2√(40000 × 10) = 1264.9 N·s/m; c = ζ cc = 53.8 N·s/m
  4. fn = (1/2π)√(40000/10) = 10.066 Hz; fd = fn√(1 − ζ²) = 10.057 Hz, practically the same

Answer: ζ = 0.043, c = 53.8 N·s/m

Chapter 24

Forced vibration: magnification factor, unbalance excitation, transmissibility and isolation

Which syllabus covers thisAU ME3491 Unit VVTU BME503 Module 5SPPU 402042 Unit 4MU MEC503 Module 5KTU PCMET501 Module 4

How does the steady amplitude depend on the forcing frequency?

Push a damped spring-mass with F0 sin ωt and, once the start-up transient dies away, it vibrates at the forcing frequency with amplitude X = (F0/k)·MF, where r = ω/ωn and MF = 1/√((1 − r²)² + (2ζr)²). Far below resonance MF ≈ 1 and the spring takes the load; at r = 1 MF = 1/(2ζ), so 10 % damping gives 5 times the static deflection; far above resonance MF falls as 1/r² because the mass's inertia resists. The response lags the force by 0° at low speed, 90° at resonance and nearly 180° beyond.

What changes when the force comes from a rotating unbalance?

An unbalance m·e inside a machine of total mass M gives a force m e ω², which itself grows with speed. The amplitude becomes M X/(m e) = r²·MF: near zero at low speed, a peak near resonance (1/(2ζ) at r = 1), and at high speed it settles to 1: the machine just orbits about the combined centre of mass, X = m e/M. A machine running above its natural frequency must pass through resonance at every start and stop. A whirling shaft is the same story; its critical speed is in the Design of Machine Elements book.

How much of the force reaches the floor?

The floor feels the spring force plus the damper force, kx + cẋ. Their ratio to the applied force is the transmissibility TR = √(1 + (2ζr)²)·MF. The same expression gives the motion of a machine whose base is shaken (X/Y). Every TR curve passes through 1 at r = √2 whatever the damping. Below √2 the mounts amplify the force; above it they isolate, and there extra damping makes isolation worse, though it keeps the resonance passage tame.

Forced vibration: magnification factor, phase, unbalance excitation, transmissibility and isolation: interactive loads as you scroll

How are isolation mounts sized?

Choose the isolation wanted, say 85 % (TR = 0.15). Ignoring damping, r = √(1 + 1/TR) = 2.77. A machine running at an illustrative 1440 rpm (24 Hz) then needs fn = 8.67 Hz, which means mounts that sag 3.3 mm under its weight, since δ = g/ωn². With ζ = 0.1 the same mounts give only 83 %, so they must sag 3.8 mm instead. Soft mounts isolate; stiff mounts on a fast machine can make things worse.

How does a seismic instrument use the same curves?

A seismic pick-up is a small mass on a spring inside a case bolted to the vibrating body, and it measures the mass's motion relative to the case: Z/Y = r²·MF. A vibrometer is built with a very low natural frequency (r well above 1), so the mass stays still and Z ≈ Y: with r = 3 and ζ = 0.7 the reading is 99.6 % of the true displacement. An accelerometer is built with a very high natural frequency (r much below 1), so Z ≈ ω²Y/ωn², proportional to acceleration.

Predict, then check

A machine runs on rubber mounts at r = 3. You add dampers that raise ζ from 0.05 to 0.5. The force transmitted to the floor

Worked examples

A machine forced near resonance · An illustrative 120 kg machine on mounts of total stiffness 600 kN/m, ζ = 0.08, carries a 400 N force at 15 Hz
  1. ωn = √(600000/120) = 70.71 rad/s; ω = 2π × 15 = 94.25 rad/s; r = 1.3329
  2. MF = 1/√((1 − 1.7765)² + (2 × 0.08 × 1.3329)²) = 1.2418
  3. X = (400/600000) × 1.2418 = 0.828 mm, lagging the force by 164.6°
  4. TR = √(1 + 0.0455) × 1.2418 = 1.2697: the floor feels 508 N, more than the 400 N applied
  5. Mounts a quarter as stiff double r to 2.666 and cut TR to 0.178

Answer: X = 0.83 mm; 508 N reaches the floor (TR = 1.27), since r < √2

A motor-driven machine with an unbalance · An illustrative 80 kg machine on 400 kN/m mounts, ζ = 0.1, running at 1440 rpm, has an unbalance of 0.2 kg at 50 mm
  1. ωn = √(400000/80) = 70.71 rad/s; ω = 150.8 rad/s; r = 2.1326
  2. MF = 0.2798; M X/(m e) = r² MF = 4.548 × 0.2798 = 1.2727
  3. X = (0.2 × 0.05/80) × 1.2727 = 0.159 mm
  4. Unbalance force m e ω² = 0.01 × 150.8² = 227.4 N; transmitted TR × that = 0.3042 × 227.4 = 69.2 N
  5. While passing through resonance at start-up: X ≈ (m e/M)/(2ζ) = 0.625 mm

Answer: X = 0.159 mm at speed (0.625 mm briefly at resonance); 69 N reaches the floor

Sizing isolation mounts · An illustrative compressor running at 1440 rpm should pass only 15 % of its shaking force to the floor (85 % isolation)
  1. Undamped mounts: TR = 1/(r² − 1) = 0.15 gives r = √(1 + 1/0.15) = 2.7689
  2. Running frequency 24 Hz, so fn = 24/2.7689 = 8.668 Hz
  3. Static deflection δ = g/ωn² = 9.807/(2π × 8.668)² = 3.31 mm
  4. With ζ = 0.1 at the same r, TR = 0.1709 (only 82.9 % isolation)
  5. Solving TR = 0.15 with ζ = 0.1 gives r = 2.953, fn = 8.13 Hz, δ = 3.76 mm

Answer: Mounts sagging about 3.3 mm (undamped) or 3.8 mm (ζ = 0.1) under the machine's weight

Keep going

Recommended reading

  • Theory of Machines, S. S. Rattan
  • Theory of Machines and Mechanisms, J. J. Uicker, G. R. Pennock and J. E. Shigley
  • Kinematics and Dynamics of Machinery, R. L. Norton
  • Theory of Mechanisms and Machines, A. Ghosh and A. K. Mallik
  • Theory of Machines, Thomas Bevan
  • Mechanical Vibrations, S. S. Rao

How this book was made

Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.003J (Dynamics and Control I), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.

From the exam to a core job

Talk to a counsellor.

Ask how mechanism and machine design engineers use theory of machines on real projects, and what the Multibody Dynamics using SolidWorks covers.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.