Week 8 - Challenge 2 - Base Bracket Design

  OBJECTIVE : The priliminary objective is to devolop the essential flanges and reinforcements for the given roof styling and to provide dimensions , check for draft analysis and to create section inertia report on the  0-Y section , then do a curvature study on the roof and perform calculations to determine…

OBJECTIVE The ultimate objective is to create a fender using the fender design skin fender and to create mounting features to attach the fender to the vehicle  FENDER Fender is the part of an automobile body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids…

WHEEL ARCJ CHALLENEGE  Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle.  The most important body change was that the front wheel arch was cut higher into the fender. The design of Wheel arch of a fender should be such that it must shield wheels and protect both passengers'…

According to the input datas they have given , we must devolop the 2d drawings into 3d solid models . Model drawing 1 shows the quick return mechanism components , QUICK RETURN MECHANISM  A quick return mechanism is an apparatus to produce a reciprocating motion in which the time taken for travel in return stroke…

OBJECTIVE  Create b pillar of a vehicle from the given class A input and devolop the part by using master section to create ribs , flanges , dog house , locators . creation of tooling axis  tooling axis decides the movement of the core and cavity during injection moulding process ,  lifter axis is the axis…

Screenshots of the Draft analysis report switch bezel plastic component   Screenshots of the core and cavity blocks in various orientations (Isometric, Front, Side, and Top View) front view      side view     top view     isometric view     PARTING LINE  parting line…

Screenshots of the completed design in various orientations (Isometric, Front, Side, and Top View) FRONT VIEW  SIDE VIEW      TOP VIEW    ISOMETRIC VIEW        TREE STRUCTURE           screenshot of the part with draft analysis   …

  Screenshots of the Draft analysis report for Class-A surface    Screenshots of the Draft analysis report for the final plastic component Screenshots of the solid model with the proper color code of the draft angle in various orientations (Isometric, Front, Side, and Top View)   FRONT VIEW   …

Screenshots of the Draft analysis report for the given Class-A surface   Screenshots of the Draft analysis report for the final plastic component   Screenshots of the solid model with the proper color code of the draft angle in various orientations (Isometric, Front, Side, and Top View) front view  side…

Image of the complete Draft analysis  Images of the color scale variant   Screenshots of the solid model with the proper color code of the draft angle in various orientations FRONT VIEW      SIDE VIEW    TOP VIEW  ISOMETRIC VIEW     OBJECTIVE    to make a…

Screenshots of the completed design in various orientations (Isometric, Front, Side, and Top View) front view    side view      top view     isometric view     OBJECTIVE  to make a detailed report on explaining the tooling axis creation for coin holder  tooling axis…

Screenshots of the completed design in various orientations (Isometric, Front, Side, and Top View) front view  OBJECTIVE  to make a detailed report on explaining the tooling axis creation for DOOR APPLIQUE tooling axis is the direction in which the core and cavity moves to make a moulded component …

hood  A car hood, also referred to as a bonnet in some other countries, is the hinged cover that rests over the engine of a front-engine vehicle. Its purpose is to provide access to the engine for repair and maintenance. ... Hoods sometimes also contain a hood scoop, wiper jets, power bulge, and/or hood ornament.…

UNDERBODY COATING  Automotive underbody coatings are applied on the underside of vehicles to provide a protective layer of protection between vehicle’s underside and damaging forces such as moisture, corrosion, stone chip damage and weather resistance. UNDERBODY COATING PURPOSES  Automotive underbody coatings…

BENCH MARKING IN AUTOMOTIVE INDUSTRY   Benchmarking involves a structured comparison between similar products, services or processes on some dimensions of performance. ... These look at products and services and provide recommendations based on which is best or some form of ranking amongst competitors. …

DOOR TRIM PANEL Door trim panel is the interference between the interior of the car and the inner workings of the car door . The door trim panel must be designed in such a way that it should withstand load and it must be more resistable during accidents or collisions and it must also satisfy aesthetically . In addition…

Screenshots of the Draft analysis report.  Image of the complete Draft analysis    Images of the color scale variant     Screenshots of the model with the proper color code of the draft angle in various orientations (Isometric, Front, Side, and Top View)   isometric view  top view …

clear all close all clc %input R = 8.314; d_1=fopen('THERMO.dat','r'); dataline_1=fgetl(d_1); dataline_2=fgetl(d_1); glob_temp = strsplit(dataline_2,' '); max_glob_temp=str2num(glob_temp{4}); mid_glob_temp=str2num(glob_temp{3}); min_glob_temp=str2num(glob_temp{2}); fgetl(d_1) fgetl(d_1) fgetl(d_1) %creating a new folder…

concept of genetic algorithm    genetic algorithm is carried out by the process of natural selection , used for solving constrained and unconstrained optimization problems , where the capable indiduals are selected for reproduction and for production of offspring of next generation . it keeps on modifying the…

https://drive.google.com/file/d/1ey2SB_6VRLYEZGT7nnEfxBd5o0xhahfQ/view?usp=sharing clear all close all clc %inputs damp_coeff=0.05; gravt_force=9.81; l=1.1; mass=0.1; %initial conditions disp_velocity= [0;5]; %time points t_span = linspace(0,10,100); %solving ode [t,out] = ode45(@(t,theta) ode_func(t,theta ,damp_coeff,gravt_force,l,mass),t_span,disp_velocity);…