Week 11 - Project - A pillar Design with Master Section

1.0 AIM Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses 2.0 INTRODUCTION 2.1 BACK DOOR   Back door or tail gate  simply refers to the back of the car that can open and close.it covering the…

AIM / OBJECTIVE: For the given roof styling. Create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs. INTRODUCTION:…

Aim To calculate section modulus of hood and optimize the design to have improved section modulus. Section modulus:- Section modulus is a direct measure of a strength of any cross sectional area of an object about an reference axis. The formula of section modulus is given by, S=I / Ymax Where,I = Moment of inertia (mm^4)Y…

DESIGN OF CAR FENDER Fender is  the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fenders are typically rigid and can be damaged…

Objective Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters.   Introduction The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk on rear-engine and some mid-engine…

DESIGN OF DOOR TRIM PANEL DOOR PANEL The door panel covers internal parts like the window regulator, the power window motor, and the wiring. It is attached to the sheet metal part of the door. It is designed differently based on the design of the sheet metal part of the door. Besides its aesthetic look, it also has…

main part draft analysis: expandable tree: cross-section:  

draft analysis: expandeble tree:

Coin Holder Design   \  

Switch Bezel Design

Base Bracket Design

Aim: Route the Wiring Harness on the given Car body and prepare to flatten the view drawing in CATIA V5 Objective: The objective of this project is to route the wiring harness and prepare to flatten the view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness…

Aim - To route the wiring harness on the given Engine and flatten the view drawing in CATIA V5. Objective - The objective of the project is to route the wiring harness on the given Engine and prepare to flatten the view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also,…

from the above drawing assembled all the electrical components with a wire bundle and protective covering.  then created one flattening product file to give properties to the product and makes some necessary changes for drawing drawing as follow    all the files are attached below

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) Download connector 3D…

  Q.1 Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Ans: Procedure to define S-Clamp is as follows: S-clamp downloaded form given site and load into the Catia V5 Define two points and two planes as entry and exit,…

Wiring harness assembly structure – connector definition Create/download connector 3D Create required geometric parameters Define parts as a connector Define “bundle connection point” Define “connector connection point” Define “cavity connection point”   CONNECTOR DEFINITION…

Thermal modelling of the battery pack A} The following blocks are used to build the battery pack Battery (Table-Based): A battery is a device that converts chemical energy contained within its active materials directly into electric energy by means of an electrochemical oxidation-reduction (redox) reaction. This block…

Mechanical design of battery pack capacity 18kWh for the Design of the battery pack used the following cell (Datasheet) Desing Assumptions are as follow: 1) Battery energy = 18 kwh 2) Voltage (to run the vehicle) = 400V Stage 1st: battery pack configuration To calculate the number of cells required for the battery…

A} Result of Simulink model – CASE 1 A lamp showing a green signal means that case one is fault free. Graphs are shown below: Driving (Discharging) mode (0-3000 sec) All the cells for the first 3000 sec are in the driving mode so the discharge of all the cells occurs and it varies in the range of 3.1 to 3.9 V (min…

1) A lithium-ion battery is a secondary type of battery which are commonly used in portable electronics & electric vehicles. Similar to a conventional battery, a Lithium-ion battery includes a cathode(+ve electrode), anode(-ve electrode), & electrode as conductor. The cathode is a metal oxide material &…

project: Hybrid architecture A hybrid vehicle is one that uses two or more distinct types of power, such as submarines that use diesel when surfaced and batteries when submerged. Other means to store energy include pressurized fluid in hydraulic hybrids. The basic principle with hybrid vehicles is that the…

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% %% Skill-Lync -> Hybrid Drives Development % Project 1 - Conventional Vehicle Model % By - Akshay Gulab Chaudhari % Description: %% Initialization File % Initialization file for loading the variables for the Conventional vehicle simulation model %%…

building hydraulic circuit needed the following components: 1. hydraulic reservoir. 2. pump 3. pressure relief valve  4. directional control valve  5. double acting cylinder. 6. hose pipe  the model looks as follows:  

1. Answer follwing are major components in above automotive wiring diagram: 1. Battery; 2. starter; 3.current and voltage regulator; 4. fuse; 5. ammeter; 6. Distributor; 7.ignition sw; 8. ignitian coil; 9.junction block; 10. generator; etc. 2.Answer a) Battery: An electric battery is a source of electric…

% This file contains the design parameters to model a DC motor J = 0.01; % Moment of inertia of the rotor in kg-m^2 X = 0.5; % Motor viscous friction constant in n-m-s Km = 0.01; % Back EMF constant in V/rad/s kt = 0.01 ; % Motor torque constant in Nm/amp Ra = 1.0; % Resistance of the armature circuit in ohms La = 0.5;…

% this method is usefull for finding result of specific gravity W0=input(' weight of empty bottle W0'); W1=input('weight of bottle + sample W1'); W2=input('weight of bottle + water W2'); x=(W1-W0)/(W2-W0); if (x>1.496 && x<1.525) disp('result is complies'); else (x<.496 && x>1.525); disp('result…