Project 1- Traffic Jam Assistant Feature

Traffic Jam Assistant Feature Introduction to the Feature: Traffic Jam Assistant is one of the most common feature in Advanced Driver Assistance System. Traffic Jam Assistant helps the driver arrive more relaxed at their destination, even in dense traffic or in traffic jams. As a partially automated comfort function, the…

Highway Assistant – Lane Changing Assistant Introduction to the Feature: The Highway Assistant supports the driver and takes over the longitudinal and lateral guidance of the vehicle in monotonous driving situations on highways. The partially automated function can automatically start, accelerate, brake as well as…

Aim: To Develop a MATLAB Simulink Model for Adaptive Cruise Control Feature as per requirement and generate a C-Code for it. Objective: Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD…

Aim: To Develop a MATLAB Simulink Model for Vehicle Direction Detection as per requirement and generate a C-Code for it. Objective: Development of MATLAB Simulink model as per requirement. Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems is fine.…

Aim: Design a battery pack with the capacity of 18Kwh by using the cell model ANR26650M1-B and prepare detailed battery pack report. Cell Model:ANR26650M1-B: The above picture shows cylinderical type cell model ANR26650M1-B. The cell model ANR26650M1-B is a high-performance lithium cell. Madeup of Nanophosphate lithium…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results. To simulate 3 test cases from the harness dashboard. We need to select the harness dashboard from the project file which we download with the reference link https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms…

1. Prepare a table that includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP, and LTO type of lithium-ion cells. Give your detailed explanation of it.   I.] Prepare a table that includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA,…

1. Search and list out the total weight of various types of aircrafts.   Here below I have attached the list of the total weight of various types of aircrafts.   The aircraft gross weight (also known as the all-up weight and abbreviated AUW) is the total aircraft weight at any moment during…

1. For a defined driving cycle, calculate the energy required for braking. What is drive cycle? A Driving Cycle is a series of data points representing the speed of a vehicle vs. time. Driving cycles are produced by different countries and organisations to access the performance of the vehicles in various ways, as for…

1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.  Indroduction: In this MATLAB demo model named speed control of a DC motor using BJT H- bridge retifier. BJT is using for switching operation similar to the operation of IGBT. When BJT conducting a forward voltage…

ypes of power converter circuits are employed in electric and hybrid electric vehicle are   AC-DC Converter DC-AC Converter DC-DC Converter or Chopper circuit   AC-DC Converter:   This AC-DC converter circuit used as a charger in EV and HEV to charge the battery by getting supply from Electrical network…

1. What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type? Mapped model of engine,motor and generator: The mapped model is one type where the data points are pre-assigned in lookup tables. The engine or motor torque requirment is sensed and the motor or engine…

Use ADVISOR tool and simulate the following  Case 1. For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. Objective: To analys the SOC of battery of the EV default model in ADVISOR tool by having…

Implement control logic of a “washing machine” using Stateflow as per given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing time of 100s. Then rinsing…

Part I: Make a Simulink model of Doorbell using solenoid block with the following details: When the switch is closed the electromagnet receives electrical power from the battery and pulls the metal arm to hit the bell producing sound. Create a situation where the switch is closed for 2 seconds and then released.…