Project 1 (Mini Project on Vehicle Direction Detection

1:Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters      …

Aim: To develop a special need for the Traffic Jam Assistant algorithm that would be prominent in the IPC algorithm. Objective: This model must be developed in MATLAB Simulink as per MBD guidelines. Code Generation Profile must be in Embedded Coder. Simulink Data Dictionary must be created for the model & must be linked…

AIM:make simulink model of adaptive cruise control as per given requirement .    General Overview:Adaptive Cruise Control Feature for passenger cars allows the host vehicle to adapt to the speed in line with the flow of traffic. Driving in heavy traffic or keeping a safe distance to the preceding vehicle calls…

Aim Of The Project:  Identifying the direction of the vehicle based on the camera input   Ojective: 1. Development of MATLAB Simulink model as per requirement.2. Tag the requirements to the Simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems is fine.3. MBD compliant…

AIM:- To study Thermal modeling of the battery pack with the help of MATLAB and SIMULINK   principle of lithium battery  is to circulate electrons by creating a difference in potential between two electrodes, one negative and the other positive, that are immersed in a conductive ionic liquid called the electrolyte.…

AIM: Prepare a detailed battery pack of Cell: ANR26650M1-B, drawing along with its enclosure, and Battery pack capacity is 18kWh. State your assumptions.   ABSTRACT: In this project, we are going to calculate the all parameters which are required for the build EV battery pack. We are going to using the Cell:…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation ?  2.Coulomb counting SOC is a measure of how much charge is available for use in the battery. For the…

1)Objective:To Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it   Fundamental Science in Li-ion Battery Materials Among the rechargeable batteries, Li-ion batteries have dominated…

 Objective :    Part A: 1. Search and list out the total weight of various types of aircrafts.  2. Is there any difference between ground speed and air speed? 3. Why is it not recommended to use aircraft engine power to move it on the ground at Airport?  4. How an aircraft is pushed to runway when…

 1:For a defined driving cycle, calculate the energy required for braking. braking force formula . The following formula is used to calculate the braking force of a car given a speed, weight, and stopping distance. F = (0.5*m*v^2)/d   Where F is the required force to stop in distnace d m is the mass of the car…

1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge.  A-following block is used in dc motor simulations model  H -bridge : The Bipolar Junction Transistor (BJT) when used for power switching applications. its will operates as an IGBT , whilr its is conductiing BJT…

AIM :  What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?  How does the model calculate miles per gallon? Which factors are considered to model fuel flow?  Run the HEV ReferenceApplication with WOT drive cycle. Change the grade and wind…

1.  Which types of power converter circuits are employed in electric and hybrid electric vehicle?    POWER CONVERTER : The task of power converter is control the flow of electrical energy by supplying the voltage and current optimally suited for user load . the large number of atomobiles around the…

AIM: To used the advisor tools for simulations . OBJECTIVES :  1.   For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. 2.   In the above case, try changing the battery capacity and…

aim :  Implement control logic of a “washing machine” using Stateflow as per given conditions of input power and water supply the lamp will be  on and off .       2:conditions : If the power supply is available, the system gets activated  If the Water supply is not available, stop…

aim : Make a Simulink model of Doorbell using solenoid block. The solenoid simply works on the principle of “electromagnetism”. When the current flow through the coil magnetic field is generated in it, if you place a metal core inside the coil the magnetic lines of flux is concentrated on the core which increases the induction…