Fender Design Challenge

Base Bracket Design and its Draft Analysis Aim- To create a base bracket plastic component through a given Class A surface and perform draft analysis n the final plastic component. Objective- Introduction- In this project we are designing a base bracket using given class A surface. The approach includes creation of Class…

Aim- Design BIW Tail gate (Back door) of passenger car through NX CAD 12. Objective- To design the tail gate (Back door) of passenger car. The report constitutes about positioning of Latch and Striker, Wiper motor, Tail Light mounting, Gas stay reinforcements with suitable emboss definitions and Hemming flanges. Back Door…

Aim- Roof design using NX 12 and its optimization by calculating heat distortion criteria,snow load criteria and section inertia analysis. Objective- 1.To develop essential flanges and reinforcements from the input styling surface. 2.Provide appropriate dimension and check for draft analysis and perform section modulus…

Section Modulus Calculation and Optimization Objective- The main objective of this project is to learn the basic tools, commands, and the calculation and optimization of the section modulus using NX CAD. The objectives of this project are as follows. To understand and learn the calculation and optimization of section modulus…

Fender Design Using NX CAD Objective- The objective of the project is to design a body in white front fender of a car with its mounting using the information provided by the styling team. The skin data and master sketch are the information provided by the styling team. Introduction- Fender- Fender is the American…

HOOD DESIGN Objective-To create the design of the car hood with inner panel, Outer panel, Striker and required reinforcement. The software used for this design-NX 12 The following steps are used in this design Develop the inner panel Develop the outer panel with hemming data. Providing the proper embossing Providing mastic…

What is Under Body Coating. Vehicle undercoating simply refers to a defensive layer of specific materials that is applied to the underpart of vehicles for protection from mold, moisture, dust, rot, and all the other road scraps.Rust is the enemy for car owners because it can destroy the metal. Over time, pieces of your…

Aim- The main aim of this report was to help Mr.D.S.Pughazhyendhi to choose a best car which fulfils his necessity by benchmarking the latest available cars in market so that he will buy a good car for his family. Case- Mr.D.S.Pughazhyendhi is a married man who lives in Bangalore which is a highly crowded city. His family…

AIM- To design and development of vehicle interior door trim using Catia V5 with given class A surface along with Master section. Also create the side attachment features as per design rules. Objective- To create the thickened part using master section for reference. To create the mounting features as per design guidelines…

4 Bar Quick Return Mechanism First we have to create the all parts of this mechanism and then assemble this. Creation of First part Create the required sketch according to the given dimension. Then pad it Creation of second part Creation of third part Creation of fourth part Creation of fifth part Assembly of all parts…

AIM- To create a B pillar of a car using the master section and Class A surface as an input and performing Draft analysis on the final model. Objective- To ensure proper tree structure is followed. Creating a tooling axis and following design rules. Creating Class B and C surface using Class A surface as an input. Following…

Door Applique Design with Engineering Features. Aim- To create a door applique and door attachment from the given class A surfaces and to create engineering features to fit the component in the main surface. Introduction- Engineering features are the extensions on the plastic components available on the class B surface…

 SCREW BOSS AND DOG HOUSE DESIGN ON COIN HOLDER AIM- Create the screw boss and dog house for the centre console coin holder considering the design rules mentioned in the video. General Rules for Screw bosses. Draft of 0.5 degree on walls of boss Thickness is 40% of the nominal wall at the base. Height to diameter…

Aim- To create an out featured rib on the centre console coin holder. Procedure- Firstly open the coin holder using the open command Rib- To create a rib first extract the base surface of the coin holder. Create a positioning sketch draw a line , constraint it and define it as an output feature. Extrude the output line…

Aim-1-To create the switch bezel plastic component through the given class-A-surface and at the              end performing the draft analysis on the model.         2-Creat the core and cavity design of switch bezel component Objectives- To ensure proper tree structure…

Aim- Creation of Center Console Coin holder design and its draft analysis To create the centre console coin holder plastic component through the given class A surface and at the end performing the draft analysis on the model. Objective- To ensure proper tree structure is followed. Geometrical sets should have a proper…

Aim- Creation of Door Arm rest with adding thickness and its draft analysis Introduction- Class A Surface- It is outermost surface of automobile which gives aesthetic look to vehicle. It is physically touchable. It is obtained from clay modelling by reverse engineering. This surface is given input to plastic product designer…

SWITCH BEZEL DESIGN Aim-To create the switch bezel plastic component through the given class-A-surface and at the end performing the draft analysis on the model. Objectives- To ensure proper tree structure is followed. Geometrical sets should have a proper name based on the sketches present inside of it. All the sketches…

AIM- Draft analysis on a fan cover Objective- The objective of this project is to know how to create a tooling axis and perform a draft analysis. Theory Draft analysis The draft analysis helps to detect if your draft part is easily removable from the mold (in case of plastic component) or die (in case of sheet metal).…

Surface Modelling of Aston Martin One – 77 Car Objective – Our objective is to make a detailed surface model of Aston Martin One – 77 Car Introduction- The Aston Martin One-77 is a two door, two seater flagship sports car built by the British car manufacturer Aston Martin. This is a very beautiful car.…

Rendering Project Objective- Our aim for this project is to render all my created surface models. Introduction- After you have created objects, lights and shaders, you can bring these elements together in the final rendering process. Alias offers industry standard sizes and types of rendering with adjustable quality levels.…

Concept Modelling of a KIA SPORTAGE car Objective- To model the complete car and apply various surface creating techniques and achieve good quality surfaces. Introduction- We will make an entire model of kia Sportage, here we will be combing all the features and parts that we have made earlier. Front and rear bumper, side…

Concept modelling of seat Objective- To observe and experience the design of a seat and then perform required process to model the same. Introduction- Some of the most parameters of any car where comfort is taken care of, is sitting more specifically seats. Seat plays an important role in comfort in facts its overall significance…

Concept modelling of steering wheel Objective- To make the model of car steering wheel from one image by visualization which provided by skill-Lync. Introduction- Concept modelling is the modelling where 3d data starts to take shape. It is a crucial part of the process as every part involved in the design process depends…

  Concept modelling of side fender Objective – Our objective is to use the provided images and make a 3D surface model of side fender and car hood by visualization. Introduction – Almost every time automotive designs are representation and imagination of the designer which is shown on the plain seet, but…

Concept modelling of front and back bumper of car ABARTH 500 Objective: - My objective is to use the 2D images of the car and to make the 3d surface model of the car bumper. Introduction: - Auto desk ALIAS is a CAID software which helps in creating the Automotive models in form of surfaces where engineers and designer…

Concept modelling of Alloy wheel   Objective: - My objective is to make the surface modelling of car alloy wheel Image which is provided by skill-Lync Image which is taken by itself is to be done using Autodesk Alias. Introduction: - Autodesk-Alias which as an automotive design software deals with surfaces. Since…

Objective: - My objective is to make the surface model of Bugatti Veyron car through Autodesk-Alias provided by skill-Lync. Introduction: - Autodesk-Alias is basically automotive design software which deals with surfaces. Autodesk-Alias  is a family of Computer aided industrial design (CAID) software predominantly…