MODELLING OF AMERICAN CHOPPER ON SOLIDWORKS   INTRODUCTION: In this project we are to learn the entire modeling of an American chopper on solid works and solid works visualize. The different components of the motorcycle we deal with are:⦁ Chassis⦁ Engine with exhaust system⦁ Front wheel and Rear wheel with rims sprockets…

   Design, Assembly and Photo-Realistic Rendering of anAmerican Predator Yacht OBJECTIVE The objective of the project is to design and model all the parts of an American Predator Yacht and assembling it to create the Photo-Realisticrendering of the yacht. INTRODUCTION In this project the American Predator Yacht…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface: STEP 1: Check…

DRAFT ANALYSIS OF A SWITCH BEZEL   AIM: To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and also Create the Class B Surface & Class C Surface. At the end perform…

Coin Holder Design AIM: to make a model from the provided class-A surface. INTRODUCTION: CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface. CLASS-B SURFACE: a surface below a certain thickness from the class-A…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A surface…

AIM : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.The core is the part which forms the internal shape of molding. The cavity is the part which forms external shape of molding.Core isthe side of the tool where the plastic part is injected from; also known as the bottom half of…

Attachment Feature Creation (Ribs & Screw Boss) AIM: To Create the Door Handle Component from the given Class-A surface.To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle.To Attach B side Features in the component.To perform the Draft analysis on the model.   TOOLS…

DOG HOUSE DESIGN INTRODUCTION Dog house is a feature that helps you to avoid sink marks. OBJECTIVE To Create the Door Handle Component from the given Class-A surface.To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle.To Attach B side Features in the component.To perform…

OBJECTIVE Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators considering…

Design A Pillar Through Master Section Development Aim:- To Design Pillar Through Master Section Development And Write a Detailed Report.Given:-A-Surface-Master Sections Overview Design Life Cycle Automotive Industry The Stages Of Design Life Cycle Are-Concept Sketches:Concept Sketches Are Rough Idea Of Free Hand Sketch…

4 Bar Quick Return Mechanism: First we have to create the all parts of this mechanism and then assemble this. Creation of First part: Create the required sketch according to the given dimension.   Then pad it   Creation of second part:   Creation of third part: Creation of fourth part   Creation of…

AIM: Download following connectors & Connector clip cad data from given link & define it asElectrical Connector using Electrical Part design Workbench. Define all the necessaryproperties to Connectors & Clip.Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)Tyco 174357-2 (https://www.te.com/usa-en/product-2-174357-2.html?source=header-match)Tyco…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P-Clamp Wiring harness assembly structure-clip definition Following important parameters required for define clip. 1.Entry point & plane 2.base plane 3.Exit plane. Process:…

Aim:1) To Route the following harness layout in the Electrical workbench.2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors.Given:CAD data of the following Connectors:DT06-4SDT06-6SDT06-2SDT06-08SAConnectors Layout Design:   Steps to be followed: 1. Download connector 3D data…

BENCHMARKING Defination benchmarking in an automobile industry involves a structural comparision between similar products,services (or) processes on some dimension of performance. it is a technical word of comparision. it's about a study of existing product. by doing a benchmarking we can sorting of a one product respect…

 UNDERBODY COATING. - Underbody coating provides long term protection from corrosion to car's underbody. - It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible but are prone to corrosion. - Underbody coating is usually a dense cladding…

HOOD DESIGN Aim: To design car hood in NX using given master section and provided design parameters.   Hood and it’s components: Hood – Car hood/bonnet is a hinged cover that rests over the engine in a front-engine car. A latch is provided under the hood in order to prevent accidental opening during…

                                                             WHEEL ARCH STUDY Calculate the Wheel Arc area using the European standards. DEFINITION: An arch-shaped cavity in the body of a vehicle, which houses a wheel is termed as wheel arch. So the design of fender wheel arch should be in a manner which can protect pedestrian…

FRONT FENDER DESIGN Objective : The main object of this project is to design the BIW(Body in white) of front fender using the fender skin data and master section as the into data by using NX CAD. Introduction : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames…

Objective: To find the section modulus of the hood and optimisation to improve the overall section modulus. Section Modulus: The section modulus (S) is geometric property of the cross section used for designing beams and flexural members. It does not represent anything physically. Formula of Section Modulus: It may…

ROOF DESIGN USING GIVEN MASTER SECTIONS Aim- To develop the essential flanges and reinforcements with appropriate dimensions and checking draft by performing Draft analysis, Calculating Section inertia, Heat distortion and Snow load on the roof. Roof- An automobile roof or car top is the portion…

Design of Back Door Aim:                To design the Back door (Tail gate) of a car from the styling surface provided using NX CAD. The ultimate aim is to design the Back Door by following the Industrial Standards. Back Door:               …

OBJECTIVE : To design an advanced casing using the sheet metal application in siemens NX. Introduction  sheet metal design is a vast domain in the design of any sheet metal industry,it is used many sectors including the aeronautics & automotive sectors , in this sheet metal casing design we will look at the design…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Box Assembly. OBJECTIVE: To design a box assembly and create a drafting of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one…

ODD SHAPED ENCLOSURE  OBJECTIVE :- To design an odd shaped enclosure and create a draft of it using Siemens NX Sheet metal application.  INTRODUCTION :-       Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental forms…

Title of the project:- Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket Objective: To design a Bracket using Siemens NX Sheet metal application. Introduction:-   1. SIEMENS NX:- NX formerly known as "unigraphics", is an advanced high-end CAD/CAM/CAE, which has been owned since 2007 by Siemens PLM Software.…

METAL BRACKET USING NX SHEET METAL APPLICATION: OBJECTIVE: This is a project to learn the step by step procedure to create a Bracket with a gusset from the given 2D drawing. INTRODUCTION: A bracket is an intermediate component for fixing one part to another. It is used to support the weight. Brackets vary widely in shape,…