steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C.

parametric study on the gate valve simulation by setting the opening from 10 % to 80%.

For this challenge, you will have to provide answers to the following questions: Q1. Describe Ahmed's body and its importance. Q2. Explain the reason for the negative pressure in the wake region.  Q3. Explain the significance of the point of separation.  Expected Results: 1. Velocity and pressure contours. …

Simulation of the flow over a cylinder and explaination of phenomenon of Karman vortex street.

Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence model and justify the results.  Calculate the wall/surface heat transfer coefficient on the internal solid surface & show the velocity & temperature contours in appropriate areas. How would you…

Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence model and justify the results.  Calculate the wall/surface heat transfer coefficient on the internal solid surface & show the velocity & temperature contours in appropriate areas. How would you verify if…

Perform a steady-state conjugate heat transfer analysis on a model of a graphics card. You can use appropriate materials of your choice for the simulation. Make sure to properly define the correct solid and fluid zones. Refer the video for further clarification and the model is provided below the video. Run the simulation…

Research Papers: Numerical study of gas-solid flow in a cyclone separator A CFD Study on the Prediction of Cyclone Collection Efficiency

What are some practical CFD models that have been based on the mathematical analysis of Rayleigh Taylor waves? In your own words, explain how these mathematical models have been adapted for CFD calculations. Perform the Rayleigh Taylor instability simulation for 2 different mesh sizes with the base mesh being 0.5 mm. Compare…

Note:- 1. Use methane-air-2step as a mixture material than methane-air. [It allows to add water in the fuel or air] 2. Use a one-step soot model to calculate the soot formation. 

  S. No CASE STUDY: METHOD: NO. OF ITERATIONS 1.                   Implicit Steady State Jacobi 208   Gauss Seidel 112    SOR 75 2.               …

https://drive.google.com/drive/folders/1y5iqc7h7spvPDl5yYtTnGc8sxy0ZNDyA?usp=drive_link   theory is described in word file attached below. please refer it SCRIPT ON MATLAB:   close all clear all clc   % ANALYTICAL FUNCTION, f(x)=exp(x)*cos(x) %ANALYTICAL DERIVATIVE %f''(x) = -2*exp(x)*sin(x)   x =pi/3;…

.

Matlab code: close all clear all clc %Week 7 - Simulation of a 1D Supersonic nozzle flow simulation using macormack method L = 3; % Length of nozzle n = [31 71]; % Grid points on z and xory axis, % taken from anderson book 31 node nuber represents throat nt = 1:2000; %time steps cfl = 0.2; %CFL number for i = 1:length(n)…

please refer the attached word file  

  Please refer the word file attached below as there are 100s of images has taken up. Important images are inserted here.   Week 2 Challenge : Surface meshing on a Pressure valve       OBJECTIVE:   For the given model, check for the geometrical errors and perform Topology cleanup accordingly.…

Objective: For the given model, check for the geometrical errors to make appropriate volumes. Create and assign PIDs as shown in the video. Perform surface mesh with the given target lengths as per PIDs. Blade stage-1 = 1 mm Blade stage-2 = 1 mm Impeller = 2 mm Shaft rotor = 1 mm Turbo casing = 5 mm Compressor casing =…

Objective: For the given model, check and solve all geometrical errors on half portion and Assign appropriate PIDs. Perform meshing with the given Target length and element Quality criteria. After meshing the half model, Do symmetry to the other side. Target lengths for the different parts of a model are as follow: Body…

Objective: For the given models: Engine, gearbox and transmission models, check for the geometrical errors and delete surfaces which are unwanted for Surface wrap as shown in the videos. After clearing geometry, Merge all 3 models and perform surface wrap. Target length for Wrap = 3 mm  AIM: As we are doing surface…

OBJECTIVE: 1. For the given model, check and solve all geometrical errors and Assign appropriate PIDs. Perform meshing with the suitable Target length and element Quality criteria. 2. Target lengths for the different parts of a model can be decided by your own. Finer mesh will give good results and will compromise…